Search the record

While the employee was cleaning M-14 Crusher, a rock impacted EE's middle-left finger.

At approximately 6:15 pm, EE was working on the platform at M280 head pulley area, during the replacement of M281 tail pulley. While removing compartments and metal plates to access the work area, one of the plates became stuck, as EE attempted to free the plate, the metal plate suddenly came loose and struck the inside of EE's left knee, causing a laceration.

When placing the hose on the connection, the end of the hose that connects to the water hose hit employee.

EE was working / cleaning around M216 conveyor area with a water hose, when suddenly and unexpectedly EE felt a pain on EE's left knee.

Working on loader assembling the center hitch, was setting rear frame on to jack stands 25 ton with 3' tubes, was adjusting the tube that sets the height, as they pulled pin that adjusts this left hand ring finger was caught in the hole of the jack stand, as tube slid down it slid onto the finger caught in the jack stand hole.

While working on M20 conveyer, a rock bounced of the empty conveyer impacting the employees hard hat.

Employee threw welding connector, looks like a clamp, it bounced back at their nose.

Employee was cleaning with a water hose, the hose became tangled causing them to twist left arm.

While working on the DL the EE had water drip onto forehead. The water ran under EE's safety glasses and into eye. When the EE woke up the next morning the eye was irritated. The EE was taken to the DR. EE's eye was flushed out. DR prescribed antibiotic eye drops. EE returned to work.

EE was working on M-11 using the pressure washing truck, as EE stepped down from the truck EE's fingers got stuck between the handrail and taillight causing a laceration of the small finger in the right hand.

While hosing off excess material from a portable crusher a piece of foreign matter entered employee's eye.

EE lacerated the palm of left had on the belt support bracket of the Pioneer Crusher, while retrieving the belt support cross member.

Employee was replacing the wire spool of the wire feeder, when the guard/cover closed impacting their head.

The day following shoveling fine material, employee said they felt soreness in their back but refused a medical exam or treatment. A medical checkup was not requested until 6/27/2017 at which time they received an appointment on the 28th.

EE was working on a conveyor belt when the connector (clip) came off striking ee on the little finger of the left hand.

Employee's right thumb was crushed and nail bed damaged (nail avulsion) when EE placed their hand in the door jamb that closed unexpectedly. Diagnosis: Avulsion fracture of rt thumb; laceration of rt thumb.

As employee attempted to insert one of the retaining pins ee felt a pain in left shoulder.

EE hit his left knee against the dozer track while he was dismounting the Cat D6 after he had fueled the dozer. The accident occurred on 10/8/2015 but ee did not request medical attention until 10/29/2015.

EE was moving a plate liner to work with it when his finger was caught between the liner an another piece of metal injuring his finger.

Employee was pulling a hose from the service truck to the portable crusher diesel tank. The hose became entangled on the stairs. As he pulled on the hose it became entangled causing his elbow to strike the diesel tank.

The day following employee's work assignment to change a motor for a lube oil pump, he felt a pain in his lower back.

EE was removing a screen from the M31-31 shaker when it slipped down striking his right index finger.

Employee felt a pinch in his lower back as he dismounted the pressure washer truck.

Employee dropped a tool inside a chute. He cut his forearm on a piece of flat bar while reaching to the tool.

EE attempted to lift the engine compartment door to gain access to the radiator when he strained his back.

While lubricating heavy equipment using latex gloves employee developed dry hands which lead to lacerations on his hands.

EE's finger was caught between a chain holding the pitman and the pitman itself when the toggle plate shifted.

While turning the Hammer on crusher M-48 employee's finger was caught in between the hammer and the wall.

When employee was setting up a pull cable, the cable fell hitting and cutting his right leg.

When moving crusher hammer he felt a pain in the groin area.

Miner was clearing material from tail pulley area, when he hurt his back.

Mounting and dismounting a loader EE further irritated a pre existing strained back. He also assisted in the removal of a wall air conditioning unit further straining his back.

Finger was injured while installing a track roller on a dozer.

Open fracture of L-hand middle finger distal phalanx (tip) resulted after screen shaker pulley being replaced by IE slipped and fell over IE's injured body part. IE is being treated by physician. He is working under restricted duty (no use of L-hand). Contributing cause: IE failed to use proper mechanical devices (come-a-long) to hold pulley in place while being replaced.

EE was on a conveyor belt that slide down, which caused him to twist and he injuring his ankle.

EE WAS ATTEMPTING TO REINSTALL AN AIR CONDITIONING VENT IN EE LOADER CAB WHEN EE FINGER WAS CAUGHT BY THE FAN

While landing a section of conveyor, set down on top of foot.

A WATER HOSE WHICH HAD JUST BEEN TURNED ON SLIPPED FROM THE HANDS OF AN EMPLOYEE AND THE WATER STRUCK VICTIM IN THE EYE.

EMPLOYEE WAS TURNING THE ROTOR SHAFT IN ORDER TO CHANGE THE HAMMERS. WHEN THE ROTOR SHAFT MOVED FURTHER THAN INTENDED HE TRIED TO GET OUT OF THE WAY, BRUISING HIS RIGHT LEG AND DISLOCATING HIS LEFT SHOULDER. NOTE: SHOULDER HAD BEEN DISLOCATED PREVIOUSLY. DOCTOR SAID SHOULDER WAS UNSTABLE PRIOR TO ACCIDENT.

CLAMP ON HOSE CUT HIS HAND WHEN THE HOSE SLIPPED FROM HIS HAND.

THUMB WAS CAUGHT BETWEEN A ROCK AND THE TIRE OF THE STACKER.

SAFETY LATCH ON THE RAIL CAR DOOR RELEASED, CATCHING THE FINGER BETWEEN THE LATCHES AND THE RAIL CAR DOOR.

WHEN THE SHAKER WAS BEING REMOVED FROM THE ROAD ROCK CRUSHER , EMPLOYEE'S LEFT HAND WAS PINNED BETWEEN THE SHAKER AND A STEEL BEAM.

AFTER COMPLETING THE WELDING TASK EMPLOYEE FED THE EXCESS WIRE BACK THROUGH THE WIRE FEED MACHINE ONTO THE WIRE REEL ASSEMBLY, EMPLOYEE'S FINGERWAS CAUGHT IN THE WIRE FEED GEARS.