Search the record

EE WAS LINING UP PINS ON BREAK-OUT TOOL. TORQUE ARM OF TOOL FELL ON LEFT HAND MASHING HAND-LACERATION TO RING FINGER L HAND.

WHILE REMOVING STUFFING BOX FROM LOAT FEED PUMP, EE WAS HOLDING BAR TO BE HIT WITH HAMMER WHEN A SMALL CHIP FLEW OFF THE BAR AND STURCK HIM IN THE CHEST, PENETRATING UNDER THE SKIN.

EE WAS CUTTING A PIECE OF STEEL PIPE 4"X12' WHEN IT DROPPED STRIKING HIS RIGHT FOOT. THIS RESULTED IN A FRACTURE TO THE GREATER RIGHT TOE.

EE HIT SELF ON THE LEFT RING FINGER WITH A HAMMER WHILE CLOSING A CLAMP ON A SHOTCRETE HOSE

HIT LEFT THUMB WITH HAMMER

EE WAS SHOVELING IN A CLOSE QUARTER AREA WHEN HEHIT HIS ELBOW. THIS CAUSED IRRITATION/INFLAMATION.

EE WAS USING A PIPE WRENCH WHEN IT SLIPPED AND HIT HIS LIP. THE HOSPITAL DETERMINED THAT STITCHES WERE REQUIRED.

EE WAS PULLING ON A PRY BAR AND DOING SO STRAINED HIS LEFT SHOULDER ROTATOR CUFF.

PORTA POWER WAS PLACED UNDER PANTO FRAME TO STRAIGHTEN THE FRAME. DURING THE PROCESS THE PORTA POWER AND EXTENSION SLIPPED AND STRUCK EE IN CHIN.

EE WAS CHANGING FINGER GRIZZLY WEAR LINER. HE WAS TAPPING ON THE LINER WITH A DOUBLE JACK TO LOOSEN THE LINER WHEN A FOREIGN OBJECT STRUCK HIM IN THE EYE.

EMPLOYEE WAS ATTACHING A ROPE TO A PIECE OF EQUIPMENT WHEN HIS LEFT HAND SLIPPED AND HE HIT HIS LEFT THUMB. THIS RESULTED IN A CHIP FRACTURE OF THE DISTAL PHALYNX OF THE LEFT THUMB.

NO NARRATIVE.

EMPLOYEE WAS WORKING ON SWING GATE AT MIN ACCESS TO PROPERTY. HE AHD CHECKED STOP ON COUNTERWEIGHT BUT WITH WEIGHT ON IT. HE THEN GO UNDER COUNTER WEIGHT AND RELEASED CHAIN DRIVE HOLDING IT WITH PIPE WRENCH. HE REMOVED PIPE WRENCH AND COUNTER WEIGHT & GATE LOWERED ONTO HIS BACK.

EMPLOYEE WAS STANDING ON A LADDER TO TIGHTEN A NUT. HE TURNED HIS BODY FOR A BETTER POSITION AND FELT HIS KNEE POP. HE ASKED TO SEE A DOCTOR ON 12-29-95. ON 1-3-96 EMPLOYEE WENT TO DOCTOR A ND WAS PLACED ON RESTRICTED DUTY.

EE WAS USING A SPADER TO DRIVE 1 1/2 BOLTS OUT OF LINER IN PRIMARY MILL NO. 3 A GUIDE TOOL WAS BEING USED TO GUIDE THE SPADER BIT ONTO THE BOLT AND KEEP BIT IN POSITION ON THE BOLTS. WHEN THE BOLT WAS DRIVEN THRU THE SHELL OF THE MILL, THE EE S FINGER WAS CAUGHT BETWEEN THE SPADER AND TOOL GUIDE TOOL HANDLE.

EMPLOYEE WAS REMOVING A WORN GRIZZLY FINGE RON THE APRON FEEDER WHEN A CHIP OF HARDENED STEEL FLEW OFF AND STRUCK THE EMPLOYEE ON THE LEFT CHEEK BECOMING LODGED.

HE WAS CLEANING UNDER A CONVEYOR WITH A HOE AND FELT A TWINGE IN HIS BACK AND HAS SINCE FELT THE NEED TO SEE A DR. AND CHIROPRACTOR.

EMPLOYEE WAS REMOVING METAL BANDING FORM BUNDLE OF ROCK BOLTS. STRAP SPRUNG AND STRUCK EMPLOYEE ACROSS THE ARM.

EE & CO-WORKER WERE TIGHTENING A CLAMP ON A PIPE. CO-WORKER WAS STRIKING CLAMP WITH A WRENCH WHEN EE REACHED AROUND BACKSIDE & HIS FINGER WAS HIT.

EMPLOYEE WAS WORKING ON A LINER CHANGE IN THE MILL.THERE WAS A STEEL BALL STUCK BETWEEN THE GRATE AND A SHELL LINER.ANOTHER EMPLOYEE POPPED THE BALL OUT WITH A DOUBLE JACK HAMMER.THE BALL FELL HITTING THE EMPLOYEE'S FINGER AND SMASHING IT BETWEEN THE BALL AND A BOLT ON THE LIFTER BAR.

EMPLOYEE WAS USING KNIFE TO STRIP WIRE THEEMPLOYEE PRCEEDED TO PULL BACK INSULATION WHILE HOLDINGTHE KNIFE AND CUT HIMSELF.

EMPLOYEE WAS USING A DOUBLE JACK HAMMER. HE SWUNG THE HAMMER & HIT HIS FOOT.

EMPLOYEE WAS INSTALLING E-CLIPS. HE WAS HOLDING THE E-CLIP AND THE HAMMER GLANCED OFF THE PLATE, CAUSING THE HAMMER TO STRIKE HIS HAND.

EMPLOYEE WAS REMOVING A PRS SWITCH WHEN THE TARCHET HE WAS USING SLIPPED & HIT HIS HAND AGAINST THE RAIL.

REMOVING A 1 1/4" P TRAP FROM AN OLD MILL DRY WATER COOLER TO USE AS A REPLACEMENT FOR ONE IN THE OPEN PIT SHOP. THE CHANNEL LOCKS SLIPPED AND HE CUT HIS LITTLE FINGER ON A SHARP EDGE. THE LAC ERATION REQUIRED 4 STITCHES. THIS WAS ON HIS RIGHT HAND.

EE WAS DRIVING A PIN WITH A SINGLE JACK A METAL SLIVER BROKE OFF STIRKING EE IN THE ARM REQUIRED STITCHES.

EE WAS USING DOUBLE JACK TO INSTALL E CLIPS WHEN FELT PAIN IN HIS LEFT WRIST.

EMPLOYEE WAS ATTEMPTING TO REMOVE A BIT FROM A BOLTER USING A HAMMER. HAD A PIECE OF METAL EMBEDDED INTO LEFT HAND.

EMPLOYEE WAS USING SLEDGE HAMMER TO DRIVE SPILLING IN AN APRON FEEDER.A SMALL PIECE OD STEEL CHIPPED OFF AND STRUCK HIM IN THE NECK.

EE WAS BARRING DONW TURNED WRONG AND TWISTED HIS BACK.

54736YEE WAS WORKING ON A MACHINE. METAL STRIP SLID DOWN THE BAR HE HAD IN HIS HAND STRIKING HIS RIGHT THUMB.

EMPLOYEE WAS STRIPPING INSULATION FROM ELECTRIC CABLE WITH A KNIFE. THE KNIFE SLIPPED, CUTTING THE EMPLOYEE'S HAND.

USING WRENCH IT SLIPPED STRUCK IN MOUTH

EMPL USING A METAL TAPE MEASURE. PULLED ON IT TO EXTEND IT AND CUT RIGHT THUMB.

EE WAS CHIPPING SOME ZINC OFF OF FLOOR AROUND A BOWL, AND PRYING WITH A BAR. WHEN THE ZINC BROKE, THE BAR SKIPPED AND HE CUT HIS LEFT FINGER. HE RECEIVED SOME STITCHES.

EMPLOYEE WAS USING A WRENCH TO TIGHTEN A CLAMP ONTO A HOSE. TURNED THE WRENCH FELT HIS WRIST POP, FOLLOWED BY EXTREME PAIN IN THE WRIST.

EMPLOYEE WAS REMOVING PIN FROM Z-BAR. WHEN HE SWUNG THE HAMMER HE FELT PAIN IN HIS BACK.

WHILE REPLACING TRANSFORMER AT LEAL ST SUBSTATION SKINNING INSULATION FORM CABLE KNIFE SLIPPED & CUT LEFT INDEX FINGER ABOVE MID-JOINT. THREE STITCHES WERE GIV EN TO EMPL. HE WAS WEARING GLOVE S AT TIME OF ACCIDENT.

USING KNIFE TO CUT PC OF RUBBER HOSE KNIFE SLIPPED SLICING R THUMB

EMPLOYEE WAS PULLING 210 ELECTRICAL CABLE THROUGH A TRAY USING 1/4" NYLON ROPE AND WRAPPING IT AROUND THE HARPOST ON THE MANTRIP.HE WAS MAKING THE LAST PULL TO GET OUT SLACK.POSSIBLE LOOP IN R OPE CAUGHT HIS FINGER.

EMPLOYEE WAS INSTALLING DUMP PADS ON A HAUL TRUCK.THE HAMMER SLIPPED AND HIT HIS LEFT ATHIRD FINGER.

EMPLOYEE WAS REMOVING A BEARING WITH A DOUBLE JACK, A PIECE OF METAL (SLIVER) FLEW UP, IMBEDDEDING ITSELF IN HIS CHEEK.

EE WAS PLACING E CLIPS WITH A DOUBLE JACK MISSED THE CLIP AND STRUCK HIS LEFT HAND WITH THE HAMER.

EMPLOYEE WAS TAKING APART A GD 83 DRILL FOR REPAIR, WHEN HE FELT SOMETHING SHARP GO INTO HIS FINGER. FINGER BECAME INFECTED & EMPLOYEE WAS REFERRED TO A DOCTOR, EMPLOYEE HAD SURGERY ON 2-12-9 1.

EMPLOYEE WAS PULLING UP A DITCH GRATE WITH A GRATE HOOK THE GRATE POPPED FREE STRIKING THE INSTEP OF THE OPERATOR RIGHT FOOT

EE WERE PATCHING A HOLE IN 4 INCH WATER PIPE IN 319 BY SAFETY ROOM WITH 4 INCH CLAMP AND RUBBER. THEY HAD PIPE WEDGED AWAY FROM TIMBER POST AND PARTNER WAS BARRING CLAMP WHILE EE WAS TRYING TO START NUT ON LOWER BOLT. THE BAR SLIPPED, WEDGE FELL OUT AND PIPE SPRANG BACK AGAINST THE POST. THE CLAMP CAUGHT THE TIP OF LEFT INDEX FINGER BETWEEN IT AND POST.

EMPL WAS USING SCREWDRIVER TO LOOSEN SCREW AT FACE LEVEL. EMPL TURNED HEAD TO LOOK AT SOMETHING STRIKING MOUTH WITH SCREWDRIVER & CHIPPING TOOTH.

EMPLOYEE WAS REMOVING A PIECE OF 8" PIPE FROM A LINE, WHEN THE PIPE SLIPPED, STRIKING EMPLOYEE ON TOP OF HIS HARD HAT.

EMPLOYEE WAS REMOVING PUMP PARTS WITH HAND HOIST & TROLLEY TROLLEY STOPS IN USE WERE DESIGNED FOR DIFFERENT SIZE OF WHEEL WHICH ALLOWED TROLLEY TO COME OFF END OF BEAM & FALL STRIKING EMPLOYEE S HARD HAT WHICH RESULTED IN A LACERATION TO SCALP

EMPLOYEE WAS WORKING ON A HYDRAULIC HOSE UNDER A MUCKER. HE HAD A WRENCH IN HIS HAND ABOVE HIS HEAD, THE WRENCH SLIPPED HITTING HIM IN THE MOUTH.