Search the record

EE WAS REMOVING A SEAL SPRING FROM 1 ROD MILL. SPRING CAME LOOSE CAUSING EE TO FALL BACKWARDS STRIKING HIS RIGHT ELBOW ON A HOSE REEL.

POSITIONING PORTAPOWER RAM,EMPL HOLDING RAM AND STEEL BAR TAKING PIN OUT OF 988 LOADER,BAR KNUCKLED AND STRUCK EMPL IN CHIN.

EMPLOYEE WAS USING POCKET KNIFE TO SPLIT POLE, KNIFE SLIPPED CUTTING LEFT INDEX FINGER.

EMPLOYEE WAS CUTTING A PIECE OF RUBBER STRIPPING FROM A SECTION OF CONVEYOR BELTING USING A POCKET KNIFE. KNIFE SLIPPED AND EMPLOYEE CUT HIS LEFT THUMB.

EMPL WAS TIGHTENING A 1-1/2" HOSE FITTING ONTO A CHARGING PUMP HIS WRENCH SLIPPED AND PINCHED AND MASHED HIS L INDEX FINGER BETWEEN THE WRENCH AND CONVERTER BRACKET

EMPL WAS STANDING ON LADDER PRYING ON PAN FEEDER WITH 6' LONG STEEL PRY BAR. BAR SLIPPED & EMPL HIT ELBOW ON BAR.

EMPLOYEE WAS USING A BAR TO UNPLUG A FURNANCE COOLER LEG WHEN THE CLUSTER OF PELLETS BROKE LOOSE AND PINNED THE EMPLOYEES RIGHT INDEX FINGER BETWEEN THE BAR AND A NIPPLE ON THE FURNACE, MASHIN G IT.

EMPL WAS HOLDING BOX END WRENCH WITH LEFT HAND WHILE ANOTHER EMPL WAS LOOSENING NUT WITH IMPACT WRENCH. BOX END WRENCH TURNED & CAUGHT INJURED EMPL'S RIGHT LITTLE FINGER FRACTURING IT.

EMPLOYEE WAS CHANGING A DRILL MACHINE ON A FAN DRILL. HE BENT OVER TO TIGHTEN NUT ON FEED MOTOR AND FELT A PAIN IN HIS LOWER BACK.

CHANGING 150 HP MOTOR ON #3 TOP GAS FAN EMPLOYEE WAS USING A 2" X 6" WOODEN BOARD TO PRY MOTOR INTO POSITION THE BOARD SLIPPED AND HIT EMPLOYEE ON THE RIGHT KNEE

EMPLOYEE WAS CL9ANING WHATS CALLED A GOONEY BREAKER AT THE DISCHARGE END OF THE PELLET ROLLER SCREENS HE WAS USING A STEEL BAR TO BREAK UP THE CLODS OF PELLETS THE BAR SLIPPED AND EMPLOYEE JAM MED HIS RT THUM6

EMPLOYEE WAS CL9ANING OUT LUMPS AND CLODS FROM A FURNACE LEG USING A BAR AND HAMMER. HAMMER SLIPPED AND MASHED LEFT HAND BETWEEN COOLER LEG STEEL AND HAMMER HEAD.

EMPL LOOSENING 1IPE FITTINGS ON REAGENT PUMP AND GOT REAGENT IN HIS EYES.RX ONLY.

CUTTING ROPE WI7H POCKET KNIFE, HAND SLIPPED CUTTING KNUCKLE OF LEFT RING FINGER

EMP WAS TIGHTEN3NG BOLTS ON #2 TAILS PUMP BASE PULLING HARD ON W RENCH AND STRAINED BAKC

EMPLOYEE WAS RE4OVING DOOR ON BOTTOM OF BUCKET ELEVATOR USING SHOVEL TO CLEAN OUT ELEVATOR & SHOVEL GOT CAUGHT IN ELEVATOR & HIT EMPLOYEE IN THE MOUTH

EMPLOYEE WAS USING A 10# HAMMER TO DRIVE WEDGES ON A SECONDARY CRUSHER.THE HAMMER MISSED THE WEDGE ADN THE HANDLE JAMMED EMPLOYEES RIGHT MIDDLE FINGER BETWEEN HE HANDLE AND THE CRUSHER SUPPORT BEAM.

EMPL HAMMERED DRILL STEEL RODS TO LOOSEN COUPLINGS TO UNSCREW RODS.A ROD BROKE OFF IN COUPLING CAUSING STEEL TO FALL AND STRIKE MAN ON SIDE OF RIGHT FOOT.

EMPLOYEE WAS REMOVING AXLE FROM REAR DIFFERENTIAL OF FAN DRILL BY DRIVING CHISEL BETWEEN AXLE & BACKING PLATE WHEN A PC OF CHISEL BROKE OFF IMBEDDING IN EMPLOYEES LEFT MIDDLE FINGER

EMPLOYEE WAS CHANGING CONVERTER TO TRANSMISSION HOSE. MAN WAS USING POCKET KNIFE TO CUT PLASTIC TIE WHICH WAS HOLDING BAD HOSE. AS HE CUT THE TIE, THE KNIFE BLADE CUT MAN S LEFT FOREARM.

INJ MAN WAS HOLDING ROUND BAR IN LEFT HAND TO DRIVE A BRASS BUSHING OUT OF A HOUSING THE BAR SLIPPED OFF OF BUSHING CAUSING MAN TO STRIKE HIS LEFT THUMB WITH HAMMER MAN FRACTURED TIP OF THUMB LEFT HAND

EMPLOYEE WAS CLEANING THE PELLET SPLITTER USING A LONG MINING BAR AS SHUTTLE CAR WAS MOVING TO THE NORTH END OF THE FURNACE BAR HIT SPLITTER AT WRONG ANGLE AND GLANCED OFF AND HIT INJURED UNDE R CHIN CUTTING IT AND CHIPPING A TOOTH

HELPING WELDER BOLT HINGE PIN IN SKIP.USING BAR AND ...BAR SLIPPED,CUTTING RIGHT INDEX FINGER.

EMPLOYEE WAS IN THE PROCESS OF USING A WRENCH TO REMOVE STUDS FROM LINERS ON BACK OF PUMP AS HE WAS BENDING OVER TOWARD HIS RIGHT WHILE PULLING ON THE WRENCH THE WRENCH SLIPPED OFF THE NUT INJ URED FELT PAIN IN HOW LOWER BACK IN THE AREA OF THE RIGHT HIP