Search the record

EE STRUCK IN STOMACH BY PORTA POWER HYDRAULIC PRESS RAM. BRUISED STOMACH.

WAS WORKING INSIDE SHOP. UNDER A CAT 773 #3 TRK.WAS USING A HAMMER & DRIFT PUNTCH TO REMOVE TIE ROD BEARING. A CHIP OF THE OUTER RACE HIT EE'S FOREHEAD ABOVE HIS SAFETY GLASSES.

IN BUCKET TRUCK CUTTING ELECTRICAL TAPE, KNIFE SLIPPED CUTTING LEFT WRIST AREA. REQURIGN 4 STITCHES.

EE WAS SPLICING BELT WHEN HE SLIPPED AND HIT HIMSELF IN HIS LEFT TESTICLE.

EMP WAS ENLARGING A CHAIN LINK TO SHOVE A WIRE CABLE THROUGH IT. WHEN HE STRUCK THE TOOL HE WAS USING, A CHIP CAME OFF AND LODGED IN HIS LEFT HAND.

EMPLOYEE WAS TIGHTENING A NUT WITH A RATCHET. THE SOCKET SLIPPED AND THE RATCHET HIT HIM IN THE LEG.

ATTEMPTED TO INSTALL CONVEYOR BELT, AND GRABED SPREADER CHAIN CRUSING BAR TO SLIDE DOWN CHAIN AND PINCHING FINGERS AND CUTTING OF TIP OF THUMB.

EMPLOYEE WAS TIGHTENING A NUT WHEN THE WRENCH SLIPPED AND HIT HIS FINGERS.

WHILE IN 13 STONE, EE WAS WORKING ON PUTTING A ROLLER IN PLACE. THE ROLLER WAS COCKED AND HE USED A PRY BAR TO PUT IN TO PLACE. FELT A POP IN THE RIGHT SHOULDER AND THEN FELT PAIN.

EMPLOYEE WAS TIGHTENING A BOLT.

EE AND EMPLOYEE WERE REMOVING AWEDGE FROM CROWS FOOT OF DRAY BUCKET. EE WAS USING A 10LB SLEDGE HAMMER, DRIVING IT AGAINST SPIKE MALL WHEN A PIECE BROKE OFF AND HIT HIM IN LOWER LIP.

EE WAS TIGHTENING A HYDRAULIC HOSE USING TWO WRENCHES. ONE OF THE WRENCHES WAS UP AGAINST CRUSHER FRAME WHILE TIGHTENING WITH THE OTHER. THE WRENCH AGAINST FRAME SLIPPED AND END OF IT HIT BETW EEN THE EYES AT TOP OF NOSE.

WHILE CHANGING SHOES IN THE V.S.I. EMPLOYEE USEDA HAMMER TO KNOCK SHOES CUT. WHILE DOING THIS A PIECE BROKE OFF HITTING AND STICKERG TO HIS NECK.

WAS PUTTING A CHUTE BACK ON THAT WAS REMOVED FOR REPAIR. USING A COME-A-LONG TO LIFT INTO PLACE. EMPLOYEE WAS GUIDING THE CHUTE TO ALIGN HOLES. A PRY BAR WAS USED TO MOVE. THE CHUTE SHIFTED AN D CAUGHT RING FINGER OF LEFT HAND. CRUSHED AND CUT THE FINGER FROM FIRST JOINT TO THE TIP.

EE WAS KNEELING DOWN NEXT TO I-BEAM FRAME. IT WAS WEDGED BETWEEN TWO I BEAMS. EE WAS TRYING TO ADJUST CHAIN HOLDING FRAME WHE COWORKER HIT THE FRAME WITH A SLEDGE HAMMER. THE FRAME CAME LOOSE AND STRUCK EE IN THE LEFT LEG ABOVE THE KNEE.

EMPLOYEE WAS ATTEMPTING TO REMOVE GREASE FITTING FROM CONVEYOR HEAD PULLEY BEARING WHILE USING A 12" CRESENT WRENCH. EMPLOYEE WAS HOLDING WRENCH IN LEFT HAND WHILE PUSHING AWAY FROM HIS BODY, WRENCH SLIPPED (EMPLOYEE IS RIGHT HANDED). THE WRENCH HANDLE HIT THE PULLEY AT A GLANCE FORCING FINGER DOWN BETWEEN FRAME AND PULLEY, IN TURN CAUSING LACERATION OF FINGER.

EMPLOYEE WAS CUTTING THE TOP OFF OF A 1 GAL JUG WHEN THE KNIFE SLIPED & CUT THE RT THUMB

EMPLOYEE WAS CUTTING A PIECE OF SKIRT RUBBER WITH A UTILITY KNIFE. HE WAS HOLDING SKIFT RUBBE RWITH HIS LEFT. HE HAD CUT TO DEEP THE BLADE WNE THROUGH THE RUBBER AND CUT HIS LEFT HAND BETWEEN THUMB AND 1ST FINGER.

INJURED WAS CUTTING THE BELT ON THE STACKER. HE CLIMBED BEHIND THE BELT CLAMP THAT WAS SECURED. WHEN HE COMPLETED THE CUT, HE LOST HIS BALANCE, FELL FORWARD AND CUT HIS RIGHT BICEP WITH THE KNIFE THAT WAS IN HIS LEFT HAND.

CRUSHER WAS PLUGGED. EMPLOYEE WAS USING A BAR TO PUSH STONE OUT OF THE CRUSHER. HE JAMMED HIS LEFT THUMB INTO THE EDGE OF MANTLE.

WHILE HOLDING END OF HOSE ON GREASE GUN WITH ONE HAND AND PUMPING GREASE GUN WITH OTHER HAND, THE GREASE GUN TURNED CAUSING HIM TO TWIST HIS WRIST.

WHILE CUTTING LAST BOLT LOOSE FROM DRIVE PULLEY ON FL WITH BOOM OF IT MACHINE HOOKED UP TO PULLEY THE LOAD SHIFTED CAUSING EE TO JERK AWAY FROM PULLEY & HITTING HIS HAND ON SIDE OF CONVEYOR FR AME

CLEANING BOLT WITH WIRE.

EMPLOYEE WAS TURNIGN A WRENCH TO BREAK LOOSE A NUT AND SLIPPED OFF THE WRENCH.

EMPLOYEE WAS CUTTING AROPE FROMT HE DRAGLINE CABLE. THE KNIFE SLIPPED CUTTING HIS LEFT THUMB.

MPLOYEE WAS CLEANING OUT SOME FROZEN STONE IN A HEAD BOX WITH A HAMMER AND CHISEL AND HIT HIS LITTLE FINGER ON LEFT HAND.

EE WAS OPENING THE GATES ON THE EAST 7 X 16 SHAKER. THE GATE WAS FROZEN. THE EE HOOKED UP A CHAIN HOIST & US RT. LET TO RATCHET HOIST & STRAINED HIP AND RT. LEG GETTING THE GATE LOOSE.

WEATHER CONDITIONS WERE DRY AND CLEAR WORK ASSIGNMENT WAS TO REMOVE SIDE PLATES FROM ROCK BOX. CHAIN ATTACHED TO HYDRAULIC HOISTING DEVICE, FAILED, CAUSING PLATE TO FALL ACROSS SCREEN, STRIK ING FOOT OF EMPLOYEE. PLANT WAS LOCKED OUT.

EMPLOYEE WAS HAMMERING ON A BUSHING AND A PIECE OF METAL FLEW OFF AND HIT HIS RIGHT HAND. AT THE TIME THE PAPERWORK WAS FILLED OUT, ON 8/30/93, EMPLOYEE'S HAND WAS A LITTLE SORE. ON 8/31/93, E MPLOYEE'S HAND BECAME SWOLLEN AND THEN EMPLOYEE WENT TO THE CLINIC. THE DOCTOR CUT OPEN EMPLOYEE'S HAND AND REMOVED A PIECE OF METAL.

EMPLOYEE WAS DOING REPAIR WORK AT J1 SPEED REDUCER. HE WAS USING A WRENCH TO TIGHTEN A NUT, THE WRENCH SLIPPED CATCHING HOLD OF MIDDLE FINGER OF LEFT HAND, BREAKING OFF EMPLOYEES FINGERNAIL.

EMPLOYEE WAS SERVICING THE 990. HE WAS IN A TIGHT AREA WHEN HE SCRAPED HIS ARM. THE EMPLOYEE'S ACCIDENT HAPPENED ON 8/11/93. EMPLOYEE DID NOT REPORT ACCIDENT TO HIS SUPERVISOR UNTIL 8/16/93. T HE SUPERVISOR THEN SENT EMPLOYEE TO THE CLINIC. NO WITNESSES WERE AVAILABLE. CANNOT SUBSTANTIATE WHETHER THIS WAS WORK RELATED BECAUSE IT WAS NOT REPORTED ON THE DAY OF THE ACCIDENT.

EMPLOYEE WAS ATTEMTPING TO REMOVE A BEARING HOUSING FOR BEARING REMOVAL EMPLOYEE WAS STRIKING THE BEARING WITH A HAMMER & A PIECE OF THE HOUSING FLEW OFF & STRUCK HIS LEFT FIFTH FINGER

WHEN EMPLOYEE CAME TO WORK THE GRIZZLEY WAS PLUGGED WITH ROCKS. EMPLOYEE PICKED UP SLEDGE HAMMER & CLIMBED UP GRIZZLY & STARTED KNOCKING ROCK OUT WHEN HE STARTED CLEANING ONE NEXT TO SIDE OF HOPPER HE HIT SIDE & HAMMER GLANCED OFF & HIT HIS LEFT FOOT.

EMPLOYEE WAS STANDING ON A LADDER TO ADJUST A TAIL PULLEYE. THE EMPLOYEE WAS USING A SOCKET & RATCHET. TO MAKE THE ADJUSTMENT THE SOCKET SLIPPED AND EMPLOYEE LOST HIS BALANCE AND FELL TO THE GROUND. HE PUT HIS HAND OUT TO BRAKE HIS FALL AND FRACTURED HIS WRIST.

EMPLOYEE WAS USING A HAMMER & HOLE PUNCH IN RAINY CONDITIONS. EMPLOYEE MISSED HOLE PUNCH AND HIT HIS LEFT THUMB WITH HAMMER.

EMPLOYEE WAS UNPLUGGING THE JAW CRUSHER WHEN HE USED THE SPUD BAR AT THAT TIME HIS HAND WAS JERKED TOWARDS THE CHUTE. THIS CAUSED CONTUSIONS TO HIS LEFT HAND.

EMPLOYEE WAS SHOVELING UNDER #2 CONVEYOR. WHEN SHOVELING SAND, SHOVEL STRUCK TIMBERS THAT PORTABLE LEGS SIT ON. IT IN TURN JARRED SHOULDER AND BACK.

EMPLOYEE USING A PRY BAR TO PRY ROCKS OUT OF OVERLOADED SCREEN,WHEN BAR SLIPPED AND EMPLOYEE CUT HIS FINGER ON SCREEN,REQUIRING STTICHES TO CLOSE CUT.

WORKMEN WERE LIFTING HEAD PULLEY BY SUING A PRY BAR WHEN SHAFT SLIPPED OFF BAR PINNING VICTIMS FINGER UNDER BEARING(THERE WAS EXCESS GREASE ON SHAFT.

EMPLOYEE WAS USING HIS RIGHT HAND FOR SUPPORT WHILE USING HIS LEFT HAND TO KNOCK MATERIAL OFF CONVEYOR PAN. HE HIT HIS RIGHT THUMB WITH THE HAMMER IN HIS LEFT HAND.

EMPLOYEE WAS HELPING TO REMOVE AN OLD BEARING FROM A HOUSING. HE WAS HOLDING A STRIKE MUAL WHILE ANOTHER EMPLOYEE STRUCK IT WITH SLEDGE. A PIECE OF THE BEARING RACE FLEW AND HIT 1ST EMPLOYEE IN THE RIGHT LEG. EMPLOYEE HOLDING STRIKE MUAL WAS INJURED. HE WAS STANDING 4" TO 5" AWAY WITH A BEARING ON SAW HOURSE 3' HIGH. EMPLOYEE HAD PIECE OF METAL REMOVED AT HOSPITAL.

USING KNIFE IT SLIPPED FROM UTTING AREA PULLED THE KNIFE TO HIM IT ENTERED L KNEE AREA

EMPLOYEE WAS HELPING CHANGE THE BEARINGS ON A SHAKER AT THE STONE PLANT, AND WAS USING A BAR TO PRY OFF THE COUNTER WEIGHT. THE BAR SLIPPED OFF AND HE HIT HIS ELBOW ON THE SHAKER.

RATCHET SLIPPED OFF BOLT HEAD BUMPING CHIN ON HANDRAIL CAUSING JAW TO SHUT & CHIPPED TEETH VERY SMALL CHIPS FROM THREE TEETH

EE WAS WORKING ON 2 CONVEYOR SPEED REDUCER TAKING THE BOLTS OFF THE MOTOR TO REMOVE THE BELTS THE WRENCH SLIPPED OFF HE LOST HIS BALANCE AND FELL BACK ACROSS THE HEAD BOX WITH HIS RIGHT LEG HU NG UNDER THE BELT. HE HAD BEEN STADING IN OIL EARLIER.

EE WAS PRYING THE BOTTOM SCREEN UP ON THE 6X16 SHAKER WITH A PRYBAR AND THE PRYBAR SLIPPED AND HIT HIM IN THE LEFT EAR KNOCKING HIS HARD HAT OFF.

BRUSHING OFF RUST WITH A WIRE BRUSH. A FOREIGN OBJECT WENT INTO HIS EYE. (RIGHT EYE)

EMPLOYEE REMOVING CHUTE LINER WITH BAR & HAMMER LINER CAME LOOSE & SLID INTO EMPLOYEES RT LEG-CALF AREA SHARP EDGE OR POINT LACERATED CALF

EE WAS ATTEMPTING TO LOOSEN RUSTY BOLT WITH BOX END WRENCH WRENCH SLIPPED OFF OF BOLT CAUSING HIM TO JERK PULLING MUSCLE ON RIGHT SIDE.

WHILE LIFTING CRUSHER BOWL WITH OUTER SHELL WITH HOIST RIGHT FOOT WAS CAUGHT BETWEEN PROTRUDING HOLD DOWN PIN & CRUSHER FRAME.