Search the record

Employee was attempting to dislodge a stone in a jaw crusher with a long steel rod. As EE used downward pressure to strike the stone, EE struck EE's right hand on the edge of a steel plate that surrounded the crusher.

Employee was doing maintenance on a conveyor belt. Employee was cutting rubber for a skirtboard with a utility knife. Employee cut themselves in the left hand through a leather glove. Employee required sutures to close the wound.

Middle finger hit with sledgehammer causing finger fracture & lacerations.

Two EEs were using tanker bars to adjust a radiator on a pallet to prepare it for shipping. As the two were both pushing on the bars, the injured EE lost control of bar and slipped off the radiator causing EE to fall to the ground. When EE fell, right knee impacted the concrete floor of the shop. EE immediately felt a pain in lower back, side, a leg.

Miner was attempting to remove a rock that was in the collection box at the top of conveyor #3 at the primary before plant start-up. Employee was prying a rock with a bar that was about 6" that was wedged against other material. While the miner was pulling the bar, the rock became free and the bar pinched EE's pinky finger on the left hand between the top of the box and the bar.

Employee slipped and struck knee with a wrench causing a small cut. Injury became reportable on 9/14/2016 when employee went for medical treatment and was give restrictions and prescription medication for infection.

Employee was using chipping hammer while doing maintenance on stone plant Deister screen. Employee's hands were sweaty and slipped down shaft of chipping hammer, hitting screen and causing small laceration, bruise and swelling. On 7/7/2016 employee sought medical attention for the swelling that had not receded. Diagnosis was broken bone in left hand.

Employee was pulling on a wrench when he felt pain in his shoulder. Employee went to the Chiropractor on 10/28/14, this is the date the injury became reportable.

EMPLOYEE USING UTILITY KNIFE TO CUT CONVEYOR BELT. KNIFE SLIPPED, CUTTING THROUGH SAFETY GLOVE, LACERATING LEFT INDEX FINGER.

EMPLOYEE CUTTING AND SPLICING CONVEYOR BELT AT CRUSHING PLANT, USING UTILITY KNIFE AND T-SQUARE - CUT RIGHT HAND WITH UTILITY KNIFE REQUIRING STITCHES AT LOCAL EMERGENCY ROOM.

Employee hit finger with a hammer while changing screen.

While loosening bolts to remove screen, felt a pop in his groin area.

Pry bar slipping, impact on left elbow causing surgery for torn bicep tendon.

EE was changing worn screen panel. Because of rain and very tight quarters inside the screen, EE slipped with a razor knife, cutting through his gloves into this finger.s

Employee was prying material out of bin when pry bar slipped and crushed 4th finger on left hand.

Struck with metal chip while removing a bearing race.

EE was cutting rubber belting when the knife (box cutter) slipped cutting his left index finger on the side.

WHILE REMOVING FITTING FROM SUMP PUMP, THE EMPLOYEE CRUSHED THE MIDDLE FINGER ON HIS LEFT HAND WHEN THE PIPE WRENCH SLIPPED FROM THE VISE AND HIT HIS FINGER.

Cut left thumb with utility knife.

EMPLOYEE HOLDING HAMMER WRENCH AND HIT WITH SLEDGE BY OTHER EMPLOYEE.

CLEANING HOPPER UNDER 5 SCREEN WITH SCRAPER. HIT HAND BETWEEN HANDLE OF SCRAPER AND ANGLE IRON BRACKET.

EE WAS SEATED USING LARGE WRENCH TO PERFORM MAINTENANCE ON CRUSHER. WHEN EE STOOD UP HE FELT PAIN IN LOWER BACK & LEG. HE WAS ASSISTED OFF CRUSHER AND AWAITED MEDICAL ATTENTION.

EE WAS USING PICKAXE TO CLEAN FROZEN CHUNKS OF STONE OFF GRATES ON STONE HOPPER. EE STRAINED BACK MUSCLES WHILE DOING SO.

EE WAS CRANKING THE HANDLE OF THE LANDING GEAR ON A TRAILER. HE LET GO OF THE HANDLE, THE HANDLE THEN REVERSED DIRECTION, SPUN AROUND AND STRUCK HIM IN THE FACE (MOUTH CHIN AREA)

EE WAS SHOVELING STONE AND WHEN HE DREW BACK THE SHOVEL IN HIS HAND, HIS RIGHT HAND BRUSHED AGAINST THE GUARD CAUSING A LACERATION.