Search the record

When rotating the classifier wheel pinched his finger between wheel and an obscure lip on the classifier body behind the wheel.

While employee was working on mill, he pinched palm of his left hand causing a laceration which required sutures.

While employee was installing shims in the ACM Mill classifier wheel he cut his thumb on one of the shims.

While employee was putting supplies away his hand brushed across the sharp edge of a bracket causing a gash to back side of left hand.

Employee was using shovel to rake garnet away from screen. The shovel caught in the pulling motion which caused employee's back to twist in the opposite direction. (Lost time began 7/21/06)

EE states that he slipped on steel stairs and struck his right shin on edge of step causing laceration.

Employee was changing bags in the dust collectors and the repetitive motion of using a screwdriver and ratchet may have caused the swelling. Note: Lost time began 8/26/05.

Employee states that while getting ice cubes out of the ice machine in Plt 2 lunchroom he noticed the ice bucket was overflowing so he dumped some ice out of the bucket. In doing so some ice fell out of the bucket onto the floor. EE then stepped on the ice and his feet went out from under him. he landed full weight on his shoulder.

Employee states that while he was working on the tail pulley bearing on elevator 015 he went to turn around and ran his knee into a piece of steel jutting out.

Employee states when he was coming around corner from ACM mill to check on #6 F-1 mill he slipped on a patch of ice on floor.

EE STATES THAT HE WAS CHANGING THE AIRLOCKS ON LINE 2 (PLT. 2). WHEN HE LIFTED AIRLOCK HE HURT HIS BACK.

EE STATES THAT WHEN HE WENT TO DUMP A WHEELBARROW OF PRODUCT HE FELT SOMETHING PULL IN HIS BACK.

EMPLOYEE STATES THAT BELT 001 WAS FROZEN TO TAIL PULLEY AND ROLLS AND THAT HE WAS PRYING BELT LOOSE WHEN HE STRAINED HIS BACK.

EE STATES THAT HE WAS GETTING A GAS TANK FOR A FORK LIFT AND AS HE WAS CARRYING IT INTO THE PLANT HE SLIPPED ON SOME ICE AND PULLED SOMETHING ON THE BACK SIDE OF HIS LEFT KNEE.

WHILE DRAGGING THE HI-VAC HOSE (WITH ANOTHER EMPLOYEE) OVER TO THE TRANSPORTER, EMPLOYEE TRIPPED ON THE HOSE AND TWISTED HIS LEFT KNEE.

EE WAS CHANGING SEAT AND FLOP GATE ON VAC., VALVE ACTIVATED AIR PISTON AND END OF FINGER ON RT. HAND GOT CAUGHT.

A PALLET STOPPED BETWEEN A CHAIN CONVEYOR AND ROLLERS. AN EE GOT UP ONT HE CHAIN CONVEYOR TO PUSH THE PALLET OUT. HE DID NOT LOCK OUT THE CONVEYOR. ANOTHER EE CAME ALONG, SAW THE PALLET STOPPE D, AND WENT TO HIT THE BUTTON TO START THE CONVEYOR. WHEN HE HIT THE BUTTON, THE CONVEYOR SUCKED THE FIRST EE'S LEG BETWEEN IT AND THE ROLLERS. THE FIRST EE HAD GOTTEN BEHIND THE PALLET WITHO

WHEN EMPLOYEE LIFTED ROLLS UP FOR SCALE THE STRAP SLIPPED ON FORK AND CAME DOWN ON RIGHT FOOT BEHIND THE STEEL TOE.

EMPLOYEE STATES THAT WHILE BRUSHING SCREENS HE FELT A SPASM IN HIS LOWER BACK. STATES THAT HE STOPPED UNTIL SPASM WENT AWAY. HE STARTED BRUSH-ING SCREENS AGAIN AND THE SPASM CAME BACK. THIS TIME IT DIDN'T STOP.

WHILE EE WAS GETTING DOWN FROM THE HEATER PIPE WHICH HE WAS STANDING ON TO TRY AND UNPLUG THE DRYER INLET PIPE, WHEN GETTING DOWN HIS FOOT SLIPPED AND HIS LEFT KNEE CAME INTO CONTACT WITH THE ANGLE FROM FLANGE.

WHILE EE WAS OPENING A PALLET OF BAGS WITH A UTILITY KNIFE, THE KNIFE SLIPPED AND CUT THE INSIDEOF HIS LEFT FOREARM.

WHILE TWO OTHER EMPLOYEES WERE PULLING EE OUT OF #1 PEBBLE MILL (ONE ON EACH ARM), THE MAN ON HIS LEFT ARM PULLED TOO HARD.

WHILE EMPLOYEE WAS DUMPING 99 LB. BAGS OUT BACK, HSI SHOULDER PULLED OUT.

WHILE EE WAS WORKING ON #2 PEBBLE MILL--NEW FEED SPOUT--DUST WAS FALLING AND GOT INTO HIS EYES.

EE WAS NOT WATCHING WHERE HE WAS STEPPING AND WALKED INTO A PIECE OF PLYWOOD CAUSING A BRUISE TO HIS LEFT KNEE/SHIN AREA.