Every injury and fatality MSHA has on file. Filter by state, year, sector, classification, experience, or any keyword from the investigator's narrative.
Email me when a new incident matches these filters. One confirmation email; unsubscribe anytime.
A customer truck driver fell off the passenger side of the trailer while closing the trailer hatches. No witnesses to the actual fall.
Employee was working on a screen and experienced worse than normal pain in back. EE was sent to the doctor for an x-ray and MRI but no treatment was received. EE back did not improve with first aid type treatment so ee received medical treatment from a physician on 5/25/18.
Employee sprained ankle while stepping off buggy in rail yard.
While cutting plate in maintenance shop, plate fell to the floor. Out of reaction employee scooted feet back quickly. Roughly five minutes later ankle/foot started to hurt.
12/21/2016, employee informed the Company that EE has had ongoing shoulder issues. Allegedly, shoulder hurt/aggravated while doing clean up work in late August or early September. Employee provided documents showing that EE first saw personal physician on 9/7/2016 and further states that MRI shows bone spurs and some corresponding issues.
Employee mashed finger between a counterweight and flange on the side of the chute, causing laceration, while clearing a chute.
Employee alleged that cladosporium previously found, tested and cleaned, was causing EE shortness of breath. Employee was taken to the hospital where all tests were clear/normal. Employee followed up with personal doctor, who took EE off work (normal spirometry/PFT). Workers compensation claim was initiated and was determined compensable on 8/3/16.
After removing the retaining screw, the lock ring on the fines screw was still stuck. The employee used a chipping hammer and a 4lb sledge hammer to tap it loose. When the employee struck the chipping hammer with the sledge hammer, a piece of metal broke off the tip of the chipping hammer, went through his leather glove and into his left thumb.
Employee and 2 helpers were changing screens and screen rubber in vibratory screen. Employee was working in a reclining position and reaching across the work surface for an extended period. When he exited the screen and began cleaning up, he experienced soreness in lower back.
Employee manually turned a full 55-gal drum of oil on a containment pallet so that the pump would fit into the opening. He experienced immediate sharp pain in the back. Employee was seen by physician on 5/31/12 and diagnosed with lumbar strain. After an MRI was performed, employee has been prescribed a treatment plan of physical therapy along with pain block to begin 06/29/12.
During lime kiln outage, employee opened door to cooler to inspect for ash buildup on grates while system was down. Dust blew into his right eye. Employee immediately washed out eye thoroughly but sought medical aid the next day and was prescribed ointment for the eye.
Employee approached a plugged air pipe at compartment A of the kiln main bag house for repairs when the bag house pulsed and the temporary plug blew off. The plug struck the employee in the mouth knocking his upper front left tooth out.
Employee was removing a bearing race that was "galled" to the shaft. The metal had been burned/cut with a torch in two places. The helper proceeded to strike the race with a 4-lb hammer to release it from the shaft. A small piece of metal flew off and struck employee in the left thigh which resulted in a puncture wound and the metal being lodged in his leg.
During restart of kiln system following a power failure, a barrier valve had to be repositioned. The air pressure was bled off to reset the valve. Upon reactivating, a burst of air/lime dust was exhausted into employee's face/eyes.
Employee assisted in lifting hydraulic cylinder and over time began to develop symptoms of strain including tingling, numbness. Physician visit on 1/27/2011.
Allegedly, employee was stepping over a vacuum hose and felt a pop in his left knee resulting in a sharp pain. Employee was under care of personal physician to determine treatment for existing condition to same knee at the time of the incident.
Employee was knocking the wooden pegs out of a C200 compressor coupling using a hammer and a chisel. The employee struck his left thumb with the hammer causing swelling and pain.
Brick dropped on finger and cut it.
Employee was using an air hose on preheater, blowing out compartments. Dust flew out of the port hole into his face causing an abrasion to the employee's right eye.
Employee was working on 220 screen firing building when the torch he was working with failed. The acetylene hose separated from fitting and ignited. A fire fall burned the screen, the fire was controlled immediable by other employee's working around. However the flash caused a burning in right face side and neck which required a medical attention/prescription.
Truck driver slipped and fell onto the ground after exiting vehicle. The ground was wet from several rainy days. The driver suffered a fractured right ankle and contusion to the right leg.
Employee was cutting a piece of vacuum pipe with a utility knife. Knife slipped causing laceration to right index finger.
Employee was opening the dribble chute when hot line dust came out and burned his chest, neck, side and ear.