Search the record

Employee was jack hammering during clean up and felt a piece of material or dust fall in EE's eye. Immediately washed-out eye but swelled up overnight and following morning took EE to the clinic to be seen and employee had a scratch to EE's eye. "Abrasion of left cornea"

Employee was performing housekeeping on a spill in an open tunnel when coworkers observed pale, heavy sweating and abnormal behavior within 15 to 20 minutes. Supervisor was notified and then EHS manager was called. Manager rushed the employee to the ER nearest to plant job site as employee was showing seizure like symptoms, the cause was determined to be dehydration.

Employee was de-icing sidewalk flatfooted on both feet. EE slipped on ice and landed on EE's back. EE was wearing EE's hard hat and as EE fell the hard hat bill forced EE's head to go forward straining EE's neck.

Sharp piece of metal after grinding

Stepping off of ramp picking up air lance hose

Employee was grinding with a corded 4 1/2" grinder on a dust collector manifold replacement at the maintenance fabricating shop and got a piece of metal in their eye due to flying debris after removing their auto darkening hood and safety glasses.

Employee was cleaning out discharge end of quencher and hurt their ankle in the process, tripping over clinker balls.

While installing a deflection shield for under the redimat, employee was notching the belt to fit correctly around the gate foot with a box cutter. Cutting towards the foot/body, the box cutter slipped and cut employee through EE's work boot and cut into inside part of EE's R foot. Seeked medical care and no stitches or restrictions.

As employee was completing their normal job duties, they were walking up the stairs and they lost their footing and at the same time their knee buckled and went backwards causing their knee to hyperextend back.

Employee was trying to move impact dolly when EE strained EE's Right shoulder

Pinched middle finger between packer roller and mounting of roller

Shoulder sprain during cleanout of ball charge hopper pit

Employee was trying to get the Gypsum feeding unplugged on the bottom of Silo #17. EE was working from a small portable platform. As EE performed the task EE slipped and EE's mouth on the silo cone, causing EE to break EE's Left front tooth.

Suspended load of kiln feed pipe slipped in strap and came in contact with employee's shoulder

Employee was helping unchoke south side air slide at the packhouse. EE climbed up on the handrail to hit the side of the air slide box with hammer. The handrail broke causing employee to fall and catch self with right hand. Causing employee to tear/rupture the bicep.

Cut to middle finger on left hand during installation of clay pump housing

Vibration from running jackhammer caused strain to right wrist

Lifting of heavy object causing sprain/strain to lower back

Miner was shooting cardox in kiln, inserted the drill bit into the port and when the air valve was turned on hot clinker dust blew back into the miner's face and arms. The miner received first, and second degree burns to face and arms. Miner was treated at ER Clinic and returned to work the same day.

Employee caught hand in pinch point of seat mechanism of forklift while trying to adjust seat. Received cut/crushing injury to left hand ring finger and finger nail.

Miner was walking by the bag house and slipped in the wet dust and twisted left ankle when trying to catch self. Weather was cold and wet.

Blowback of natural gas from kiln ignition

Hot meal from kiln operation coming in contact with employee's neck

Stepped off of ladder pulled knee

Employee was in the quencher dryer are helping clear a choke up in the kiln throat. Employee was using a sledgehammer to hit the side of the chute. When they struck the chute they felt a discomfort in their upper body.

The miner was removing duct tape from a coupling for KWF-1 using a knife and when the shaft accidentally rolled EE cut EE's left knuckle on EE's index finger and EE needed stitches

The injured employee was walking down the stairwell of the finish mill building when EE fell landing on their right hand.

Use of sledgehammer to drive shim hit thumb

Cut to the hand from a utility knife

Annual hearing tests resulted in employee experiencing reportable hearing loss.

Lifting strain on lower back muscles.

The injured miner was removing broken bags from under the palletizer area when EE injured EE's lower back.

The injured miner was jack hammering out a choke up in the throat that goes into the quencher dryer when received chemical burns from clinker dust. EE did seek immediate medical attention but the pain got worse later on and they went to an urgent care clinic the next day.

Employee was repairing part of stretch hood at palletizer for packaged cement production line. Knife blade used to cut bags over top of pallets cut into employee's hand.

Employee was descending staircase and tripped and fell down three subsequent steps landing on their knee. Knee sustained a sprain.

The Injured Miner (IM) was striking a air line when a build up of mud fell striking the IM's hard hat and right shoulder causing neck trauma and chipping a tooth.

The injured process foreman was assisting in shooting out a ring in the kiln with a shot when some material got into right eye.

The injured process attendant IV was washing down the raw mill basement area floor when they slipped on green algae injuring their right knee.

Employee was carrying large clinker ball removed from clinker discharge. When they stepped off of clinker drag they felt a sharp pain in lower back and pain shooting down both legs following with numb feet. Employee sought medical attention and incurred lost time as of 8/20/19

Employee was returning excess sampled cement back into finish mill via 5 gallon bucket. Employee lifted bucket full of cement up to reclaim screw and strained shoulder in process. Employee sought medical care and had physical therapy. Recent MRI indicated tear in shoulder and employee was referred to surgeon. Employee underwent surgery 10/9/19 and began losing time from work.

Employee got loader stuck in kiln dust and when EE exited the cab stepped into a mixture of kiln dust and water which entered both boots causing an alkali burn to the top of the feet and the ankle.

The Injured employee was assisting with removing screens from a raw ball mill when the screen dislodged fell and struck EE's right foot and wrist.

The Miner was removing bars from a cement mold when the screwdriver ee was using slipped and struck left thumb and nail.

The Injured Employee was opening a rail hopper car door with a bar when the bar slipped causing the IE to fall to the ground landing on right wrist.

The injured miner was jackhammering in the quencher dryer and removing the loose material with a shovel. When EE bent over and twisted to remove the material, EE felt a pull in lower back. EE did not seek medical attention until 10/07/2018.

The consultant was eating breakfast in a small conference room when the consultant suddenly collapsed in the chair. CPR was administered until emergency responders and EMS arrived.

The Miner was working on the finish mill chute choke up with a rivot buster. The air hose of the rivet buster moved knocking a 6' bar over striking miner's back causing a bruise. Miner did not seek medical attention until 6/13/2018.

Employee was removing discharge head liner when the liner slid causing the employee to move and lose balance causing EE to fall over on left side. Employee received a laceration to left leg below the knee.