Search the record

EE WAS USING A BELT KNIFE TO CUT A PIECE OF RUBBER OFF THE PIT BELT. THE KNIFE SLIPPED AND THE POINT OF THE KNIFE PUNCTURED HIS LEFT HAND BETWEEN THE THUMBE AND INDEX FINGER. EE WAS TAKEN TO T HE HOSPITAL AND WAS SUTURED.

EMPLOYEE WAS REMOVING THE DRAIN PLUG FROM A 100 TON HAUL TRUCK TRANSMISSION. THE WRENCH HE WAS USING BROKE CAUSING THE EMPLOYEE TO LOSE HIS BALANCE AND FALL AGAINST THE DRAIN BARREL. EMPLOYEE HIT HIS ELBOWS AGAINST THE BARREL WHEN HE FELL. HE IS SUFFERING INFLAMATION AND SWELLING TO HIS LEFT ELBOW.

AFTER SPLICING #25 BELT HE WAS REMOVING THE CLOAMPING TOOL AND THE THREADS BROKE OFF A BOLT HOLDING THE CLAMP TOGETHER LETTING CLAMP STRIKE EMPLOYEE ON HIS LEFT HAND AND BRUISED AND FRACTURING TIP OFF LEFT RING FINGER.

EE WAS TIGHTENING BOLTS ON CONE CRUSHER AND RATCHET BROKE AND INJURED FELL TO CATWALK.

EMPLOYEE WAS ATTEMPT ING TO LOOSEN JAM NUTS USING A SPUD WRENCH & CHEATER PIPE EMPLOYEE SUFFERED STRAINED MUSCLES IN HIS LEFT SHOULDER & BACK RESULTING IN TWO (2) DAYS LOST TIME

LIFTING STEEL PLATE USING A HOIST BUT AREA IS CONFINED AND RESTRICTED.

EE WAS CUTTING A CONVEYOR BELT WITH A KNIFE. THEKNIFE SLIPPED CUTTING EE ON LOWER LEFT LEG.

EMPLOYEE WAS USING A UTILITY RAZOR KNIFE TO OPEN A BOX. THE KNIFE SLIPPED EMPLOYEE SUFFERED A CUT TO HIS LEFT THUMB. THIS CUT REQUIRED FOUR STITCHES.

HE WAS USING A PRY BAR TO HOLD UP STEERING CYLINDER ON A 50 TON TRUCK WHEN THE BAR SLIPPED CATCHING HIS RIGHT HAND BETWEEN THE BAR AND CONCRETE FLOOR.

EE WAS CUTTING A RUBBER HOSE WITH A KNEE, THE KNIFE SLIPPED CUTTING THE LEFT HAND OF EE. THE CUT REQUIRED THREE STITCHES CUT WAS ON LEFT HAND BETWEEN THUMB AND FOREFINGER.

INJURED EE WAS USING AN EIGHT POUND SLEDGE HAMMER TRYING TO DISLODGE A PIECE OF METAL PLATE HE HAD JUST CUT. THE HANDLE BROKE, STRIKING HIM BELOW THE RIGHT EYE.

REPLACING SHEAVES ON SHAKER SCREEN WHEN SWING HOIST THAT WAS HOLDING UP SHAKER CAME LOOSE THUS FREEING 14" BEAM TO SWING AROUND AND STRIKE VICTIM IN THE BACK, KNOCKING HIM INTO OTHER METAL OBJ ECTS. THIS RESULTED IN INJURIES OR CONTUSIONS TO THE BACK AND SIDE.

EMPLOYEE WAS USING A HYDRAULIC JACK TO PUSH A PIN OUT OF A LOADER BUCKET WHEN THE HOSE CONNECTOR CAME LOOSE STRIKING EMPLOYEE ON RT LEG

EMPLOYEE WAS CLEANING OUT A PLUGGED DISCHARGE CHUTE FILLED WITH LIMESTONE ROCK. WHILE DOING SO, SOME OF THE MATERIAL FELL, STRIKING HIS RIGHT HAND. EMPLOYEE SUFFERED TWO BROKEN FINGERS ON HIS RIGHT HAND. THE MIDDLE FINGER AND THE RING FINGER ON HIS RIGHT HAND WERE BOTH FRACTURED.

EMPLOYEE WAS INSTALLING SCREEN CLOTH ON 8X20. EMPLOYEE WAS USING A 3/4" DRIVE RATCHET TO TIGHTEN J-BOLTS. EMPLOYEE'S SOCKET SLIPPED OFF NUT, HITTING FINGER ON J-BOLT BELOW ONE HE WAS TIGHTENIN G.

EE WAS HELPING INSTALL SCREEN CLOTH IN VIBRATINGSCREEN. HE WAS USING A PRY BAR TO ALIGN THE CLOTH. THE BAR SLIPPED, STRIKING EE IN THE MOUTH, CHIPPING TWO FRONT UPPER TEETH. EE REQUIRED DENTAL TREATMENT FOR THE INJURY TO HIS TWO UPPER FRONTTEETH.

EMPLOYEE AS ATTEMPTING TO REPLACE GRIZZLY BAR. THE MATERIAL WAS HOOKED WITH A CHAIN AND BEING PLACED BY A GROVE CRANE. THE GRIZZLY BAR SHIFTED IN THE CHAIN AND STRUCK INJURED'S LEFT THUMB.

EMPLOYEE WAS USING A PRY BAR TO POSITION A ELECTRIC MOTOR IN A SPEED REDUCER

EMPLOYEE WAS SPLICING CONVEYOR BELT WHEN THE BELT PUNCH BROKE & THE BOTTOM PART FLEW OVER & CUT THE THUMB OF RT HAND

EE WAS UNSCREWING NUT FROM BULT WITH BIG 30 LB WEIGHT ON IT. BOLT CAME OUT OF VICE ALLOWING THE WEIGHT TO FALL ON EE S RIGHT FOOT JUST BEHIND HIS STEEL TOE. BREAKING LITTLE TOE ON RIGHT FOOT.

EMPLOYEE WAS UNSTOPPING CHUTE OVER SPOKANE CRUSHER. EMPLOYEE HA DHIS LEFT HAND ON THE HANDRAIL WHEN A 4" ROCK FELL APPROIMATELY 10' STRIKING EMPLOYEES HAND.

EMPLOYEE WAS HOLDING A PIN TO BENT HAMMERS OUT OF HAMMER DRILL OTHER EMPLOYEE WAS HITTING PIN WITH A 20PD HAMMER THE HAMMER RICOHED OFF PIN HITTING EMPLOYEE HOLDING PIN ON THE FOREHEAD ABOVE R IGHT EYE

EMPLOYEE WAS TIGHTENING BOLT ON THE SKIRT BOARD OF THE RIVER CONVEYOR. THE BOLT BROKE, CAUSING THE RATCHET TO STRIKE EMPLOYEE IN THE LIPS AND CHIPPING ONE TOOTH AND CRACKING ANOTHER.

WORKING ON MUSTANG SKID LOADER BUCKET. HITTING BUCKET PIN WITH HAMMER -HAMMER SLIPPED AND HIT CONTROL ON LOADER CAUSING BUCKET TO FALL AND PIN ARM ON MACHINE.

INJURED WAS GREASING APRON FEEDER AND HAD FLASHLIGHT IN ONE HAND AND GREASE GUN IN OTHER HAND AND LOSTI FOOTING FALLING APROX. 5 FT.

EMPLOYEE WAS HOLDING PIN TO DRIVE PIN OUT OF HAMMERS IN THE HAMMER MILL. EMPLOYEE HITTING PIN WITH A 20LB HAMMER MISSED PIN AND HIT EMPLOYEE ON LEFT THUMB, CRUSHING THE THUMB.

EMPLOYEE WAS DOING MAINTENANCE REPAIR ON TAIL SKIRT OF #2 CONVEYOR HE WAS WORKING IN A TIGHT AREA WITH A KNIFE WHILE MOVING AROUND EMPLOYEE HIT HIS ARM AGAINST THE WALL & CAUSED THE KNIFE TO H IT HIS LEG EMPLOYEE REQUIRED FOUR STITCHES TO THE CUT ON HIS RT LEG

STEEL BAR ON SPUD CLAMP CAUGHT RIGHT INDEX FINGER AGAINST SPUD FRAME.

EE WAS WASHING FLOOR OFF IN LIME HOUSE. EE CUT LEFT THUMB LACERATION.

EE STATED HE WAS WORKING ON HEAD OF RIVER CONVEYOR. HE WAS CUTTING A HOLE IN RUBBER FOR THE CHUTE. KNIFE SLIPPED AND CAME ACROSS THUMB ON LEFT HAND CUTTING THUMB. WAS USING AN OLD TIMER POCKET KNIFE.

EMPLOYEE WAS HELPING CHANGE SCREEN. SCREEN WAS IN PLACE. EMPLOYEE WAS TIGHTENING DOWN J-BELT WITH RATCHET AND SOCKET. RACHET SLIPPED OFF NUT CAUSING EMPLOYEE TO HIT RIGHT HAND ON FRAME OF WASH ER SCREEN.

54736YEE WAS SHOVELING UNDER THE BARGE AND HIT HIS BACK ON THE BEAM UNDER THE BARGE.

EMPLOYEE WAS TIGHTENING BOLTS ON ROCK BOX. THE WRENCH SLIPPED OFF THE BOLT AND EMPLOYEE HIT THE SIDE OF THE ROCK BOX WITH HIS ELBOW.

EMPLOYEE WAS HELPING TAKE A BEARING OUT OF 8X20 SCREEN ANOTHER EMPLOYEE (WITNESS) HAD CUT BEARING.EMPLOYEE USED A 2 PD BALL PIN HAMMER TO KNOCK OUT BEARING.WHEN EMPLOYEE HIT BEARING A 1/8" PIE CE OF LOOSE AND LODGED IN HIS LEFT CALF.

EE WAS USING A 16 LB SLEDGE HAMMER TO DRIVE CUTTERHEAD OFF OF THE SHAFT IN ORDER TO REPLACE OIL SEAL A SMALL PIECE OF METAL CHIPPED OFF THE HAMMER AND WAS EMBEEDED IN TOP OF EE RIGHT FOOT EE WAS WEARING TENNIS SHOES.

DURING ROUTINE MAINTENANCE EMPLOYEE WAS INT EH CRUSHER BELOW THE HAMMERS, FELLOW EMPLOYEE WAS ROLLING THE HAMMERS WITH SPOTTER, DEBRIS FELL FROM THE HAMMERS INTO THE EMPLOYEE RIGHT EYE. EMPLO YEE SUFFERED EYE IRRITATION AND REMOVAL OF FOREIN OBJECT FROM HIS RIGHT EYE BY PHYSICIAN.

WHILE WORKING ON #2 SCREEN EMPL WAS CUTTING SCREEN RUBBERS WITH A UTILITY KNIFE.IT SLIPPED CUTTING EMPL ON WRIST.CUT REQUIRED 3-4 STITCHES.

EMPLOYEE WAS USING A UTILITY KNIFE TO CUT A PLASTIC SCREEN PANEL KNIFE SLIPPED AND CUT HIS LEFT HAND.

I.NAME CLEANING DEBRIS FROM RAIL CAR FROM BOTTOM DOORS AND PULLED MUSCLE IN BACK.

EMPLOYEE WAS DRIVING A PIN BACK IN HAMMERMILL WHILE CHANGING HAMMERS & A PIECE OF THE PIN CAME OFF STICKING IN HIS LEFT THIGH

EMPLOYEE WAS SHOVELING UNDER THE DUST POT ON A DRILL RIG. EMPLOYEE PULLED OR STRAINED SOMETHING IN HIS RIGHT SHOULDER WHILE TRYING TO REACH BACK UNDER THE DRILL RIG WITH HIS SHOVEL. EMPLOYEE S UFFERED CERVICAL WITH RIGHT ARM RADICULTITIS SPRAIN.

EMPLOYEE WAS REPLACING A STABALIZER BAR PIN ONT HE WATER TRUCK. HE WAS STRIKING THE PIN WITH A HAMMER WHEN A PICE OF METAL CHIPPED FROM THE PIN, STRIKING THE EMPLOYEE IN THE LEFT ARM. EMPLOY EE RECEIVED PUNCTURE WOUND REQUIRING TWO STITCHES.

EMPLOYEE WAS CUTTING INSULATION TAPE FROM MOTOR LEADS WITH AUTILITY KNIFE. EMPLOYEE WAS CUTTING TOWARD HIS BODY RATHER THAN AWAY FROM IT. UTILITY KNIFE SLIPPED AND CUT EMPLOYEE ON HIS LEFT A RM. EMLOYEE REQUIRED 5 STITCHES.

KNOCKING BEARINGS OFF SHAFT IN SPEED REDUCER.PIECE OF METAL CAME OFF,WENT INTO CHEST.DR MADE SMALL CUT,REMOVED METAL,CLOSED WITH 3 STITCHES.EMPL RETURNED TO WORK.

INSTALLING FRICTION BANDS ON DRAGLINE PLACE DHAND ON BAND OTHER EMP HIT BAND WITH HAMMER

WORKING ON PUMP HIT RING FINGER ON L HAND SCRAPING FINGER

EMPLOYEE WERE FINISHING UP FROM MAKING REPAIRS TO A CONVEYOR TAIL PULLEY. IN THE PROCESS OF REMOVING A COME-ALONG, THE INJURED EMPLOYEE DROPPED IT ON HIS FOOT.

TIGHTENING VISE HAND SLIPPED OFF HANDLE STRUCK HIS THUMB ON HANDLE

EMPLOYER WAS USING A SMALL BAR TO UNWEDGE A STEEL PLATE THAT WAS IN THE DUMP BOX OF A CONVEYOR.THE EMPLOYEE JUST BARELY TOUCHED THE PLATE WITH THE BAR AND THE PLATE SPRUNG UPWARD WITH FORCE ST RIKING THE EMPLOYEE ON THE HAND.

A FELLOW EMPLOYEE WAS USING A PARTS CLEANING GUN, WHEN THE GUN BECAME STOPPED UP HE REACCHED TO PULL THE HOSE FROM THE CONTAINER. THE FELLOW EMPLOYEE PLACED HIS FINGER OVER THE END OF THE GUN , BACK-FLUSHING THE HOSE. THE CLEANING LIQUID SPLASHED ONTO HIS FACE, GETTING INTO HIS EYES.