Search the record

Employee was holding a wedge used to remove a stuck sheave pulley on a motor shaft. Another employee was striking the wedge with a 4lb. hammer and the hammer missed the wedge and struck holding employee in top of left hand. Employees were wearing full PPE, but hammer strike resulted in fracture of left hand.

IE was holding the t-handle punch while co-worker was hitting it with a sledge hammer. Co-worker missed and the hammer hit the side of the crusher causing the hammer to ricochet hitting IE's hand.

Employee was hammering a wedge in on a screen, with a hammer and strained left shoulder.

Employee was using a pry bar to dislodge a rock in the tail pulley of a conveyor. After the rock was dislodged and employee was sliding out the pry bar, their hand struck a rock and resulted in laceration of their finger.

EE was cutting on a conveyor belt with a pocket knife slipped and caused the knife to fold cutting EE's left index finger. EE had 4 stitches. EE didn't use the proper tool to cut the belt, so EE was let go on 3/25/2021. EE was working through a temporary service.

Nailing stakes in the ground with sledge hammer when employee hit the top of right foot suffering a contusion.

IE was helping with changing v-belts. The belts were put back on but 1 belt was twisted, so another EE was using a pipe wrench on the shaft and it slipped off causing the belt to roll back pinching IE's thumb.

Employee was straightening up a clamp bar on a conveyor belt, using a hammer to line it up and hit thumb.

EE was holding metal piece while tightening bolt with other hand. When the bolt was tight ee moved left out of the way and finger was cut on a burr from the metal ee was holding. Left index finger

EE was shoveling out a feeder when EE smashed EE's finger between the shovel handle and the frame of the conveyor.

EE was working on a track hoe bucket and was hitting the bucket with a 4lb hammer when a piece of the hammer broke off going into left upper thigh.

EE was using a pry bar when it slipped and hit ee above right ear. EE was wearing hard hat.

Was changing v-belts when pipe wrench slipped causing his hand to go around the shive cutting his right hand little finger

He was adjusting v-belts on the main feeder with a wrench when the wrench came loose it smashed his finger between the I-beam and wrench.

He was cutting a piece of flashing when the blade came out of the flashing cutting his thumb.

Was using a crescent wrench when the wrench slipped and hit his mouth and tooth.

EE was holding the pin while another ee was using the hammer to drive the pin into the chain when a ee missed hitting ee finger.

Was using a 16lb hammer to strike the loader bucket to remove the shank, when a piece of metal came off, hitting him in the lower left leg. He was treated with just first aid, they said to just leave the metal in. Then the doctor decided to remove the metal on 4/29/11 and he was released to full duty.

Beating in a wedge when the hammer slipped off and smashed his finger between the shaker and hammer. Smashing his right index finger.

When he first went to the clinic they did first aid and said to leave the metal in that it would be ok. Now he has an infection and the metal has moved into a muscle, so now they will be doing surgery on 9/22/10. What had happen was he was removing a belt clam with a hammer and the chisel made for belt clams when a piece of metal went into his leg.

EE was drilling with the beetle drill. He moved the pipe wrench from the holding position around to break the steel from the power head smashing his finger between the wrench and the tracks on the drill.

He was taking out kingpins when his hammer slipped and smashed his finger.

The weld broke loose on piece of metal and the porta-power came up and hit him in the nose.

Employee was using wrench to remove hose and it slipped off of nut and left hand hit bottom of engine block. Laceration to 2nd knuckle of hand.

Metal sheave counterwight came loose from a come-a-long and fell across his lower leg and foot.

Tighten bolt on bottom of gear box at a head pulley with wrench when the wrench slipped off a cut his left elbow on a guard.

Was removing a big rock from the grizzley with a bar and pulled upward on the bar hurting his back

Was inside shaker changing screens and replacing bed rubber, when he was cutting a piece to install and cut his thumb.

Employee was beating on a piece of metal to close off chute when he hit a rock that came up and glanced his left eye.

Hammering norback when the material fell and a piece fell on his ankle and foot.

Unbridging SB2 bin when mud clot came down and bent left hand back hurting his wrist.

unplugging chute that had a piece of metal in it when the metal cut his right index finger.

Was unbridging the bottom of the Jaw and a rock fell and hit the bar mashing his finger against the wall.

Pulling motor back with come-along when the hook broke as he was pulling on the handle, causing him to slip and cut his hand on a piece of metal.

Cutting shrink wrap off motor with pocket knife and cut hand.

Contusion to the right shoulder when a port a power jack fell while squaring off the sprider on the gyro

Changing tire on water truck using a breaker bar to tighten lug nuts was pulling up when had a pain in lower back. He didn't report to worker comp. till 8/8/05. They felt that is wasn't compesable and went to court. Just settled that it was worker comp. Missed 33 day and still on restricted.

Cleaning tail pulley with shovel, he hit frozen dirt which kicked back the shovel putting pressure on his back.

Changing flashing on C4Y when his wrench slipped and he cut his arm on a piece of metal.

Driving a screen wedge with a 4 lb hammer on the left hand bottom deck 6x16 and missed the wedge and hit his finger on the bar grate cat walk.

HAND SLIPPED WHEN HAMMERING A WEDGE ON THE 6 BY 20 AND HIT THE GUARD.

WHILE INSTALLING BUSHING IN SHOVEL BUCKET HAMMERBROKE OFF AND STRUCK EE IN THE HEAD.

PULLING ON 18" CRESCENT WRENCH WHILE WORKING ON GYRO CRUSHER.