Search the record

CHAIN BROKE AND HEATER FELL ON HIS LEG.

EE WAS BETWEEN A MINING MACHINE CONNECTED TO A MOBILE GENERATOR WITH A CHAIN, NEITHER EQUIPMENTOPERATOR NOTICED HIM THERE. WHEN THE MOBILE GENERATOR OPERATOR PIVOTED HIS MACHINE, THE CHAIN TIGHTENED AND STRUCK THE EE ON THE RIGHT LEG CAUSING A MUSCLE STRAIN AND EXTENSIVE BRUISING

WHILE ROOF BOLTING, A LARGE ROCK FELL FROM THE ROOF TO THE GROUND AND THEN FELL OVER ONTO EMPLOYEE'S RIGHT UPPER LEG CAUSING A LARGE BRUISE AND ALSO CAUSING PAIN IN THE RIGHT HIP AND LOWER BAC K.

EE WAS OPERATIONG A FLETCHER ROOF BOLTER; HE WAS GUIDING THE BOLT UP INTO THE BACK, PLATE ON THEBOLT DID NOT SLIDE DOWN, PINNING HIS HAND UNDER THE CENTRALIZER. LEFT MIDDLE & RING FINGER WERE BRUISED & LACERATED.

EE AND A COWORKER WERE PUTTING UP CHAIN LINK ON THE RIB. WHEN THE COWORKER TRIED TO REPOSITION THE CHAIN LINK WITH THE PICK ON THE BOLTER BOOM, IT SLIPPED OFF THE PICK, CAUSING THE DRILL STEEL TO COME LOOSE, STRIKING THE EE ON THE HEAD. THE EE SUSTAINED CUTS AND BRUISES TO THE HEAD, AND WAS DIAGNOSED WITH A CONCUSSION.

EMPLOYEE WAS OPERATING A FLETCHER BOLTER WHEN A PIECE OF DRILL STEEL BECAME PINCHED IN THE CLAMP LEVER, RESULTING IN BRUISING AND SWELLING.

EMPLOYEE WAS OPERATING A RAMCAR WHEN A LARGE ROCK BECAME CAUGHT BETWEEN THE TAIL OF THE MINING MACHINE AND THE BACK. THE ROCK FELL ONTO EMPLOYEE'S RIGHT SHOULDER, CAUSING BRUISING.

EE STATES THAT THIS IS A REPETITIVE MOTION INJURY.

EE HAD BEEN WASHING GREASE FROM LARGE METAL SWING CASE COVER AND WAS WASHING HIS BOOTS BEFORE GOING TO BREAK. HE APPARENTLY PLACED THE END OF THE WAND TO CLOSE TO HIS RUBBER BOOTS AND THE COMB INATION OF PRESSURE AND HEAT TORE THRU THE BOOT ALLOWING HOT WATER AND STEAM TO BURN HIS RIGHT ANKLE.

EMPLOYEE WAS HOLDING SPUD WRENCH ON THE HEAD OF A BOLT THAT WAS HOLDING TWO PIPE FLANGES TOGETHER AS COWORKER WAS TIGHTENING OUT ON THE BOLT WITH AIR POWERED IMPACT WRENCH THE SPUD WRENCH SLIP PED OF THE BOLT AS IT WAS BEING TURNED BY IMPACT WRENCH CAUSING SPUD WRENCH TO FLIP BACK HITTING EMPLOYEE

EMPLOYEE WAS USING A 2 1/2" IMPACT WRENCH TO REMOVE BOLTS FROM HOIST CABLE ON DRAGLINE. SOCKET WAS ATTACHED TO IMPACT WRENCH WITH A PIECE OF THREADED ROD AND A NUT ON EACH END. SOCKET SLIPP ED OFF OF BOLT AND THE END OF THE THREADED ROD CUT EMPLOYEES ARM. LACERATION REQUIRED FOUR STITCHES. EMPLOYEE RETURNED TO THE SAME JOB WITHOUT ANY LOST TIME.

ANOTHER EE WAS USING A 3/4 IMPACT WRENCH. THE IMPACT MALFUNCTIONED AND SPUN THE NUT OFF CAUSING IT TO FLY OFF.

WORKING IN MILL AREA EYES BEGAN TO BURN AND WATER.

WORKING IN MILL-FLOTATION AREA EYES BEGAN TO BURN AND WATER.

WORKING IN MILL AREA- EYES BEGAN TO BURN AND WATER.

WORKING IN MILL AREA AND EYES BEGAN TO BURN AND WATER BY THE END OF SHIFT UNABLE TO WORK.

WHEN COMING OUT OF THE HOLE AND BREAKING DRILL PIPE LOOSE, CABLE BROKE ON TONGLINE, HITTING HIM IN UPPER CHEST AND KNOCKING HIM DOWN.

EE WAS USING A GRINDER TO CUT A PIECE OF FLAT METAL THE GRINDER GRABBED JERKED OUT OF HIS HAND AND HIT HIS RIGHT WRIST.

USING IMPACT WRENCH, SAND BLEW IN FACE.

CUTTING METAL OVER HEAD PIECE OF SLAG FELL INTO LEFT EYE.

EMPLOYEE ALLEGES THAT AFTER WELDING FLANGE ON JACK STAND SLIPPED AND FELL STRIKING RIGHT GREAT TOE SUSTAINING FRACTURE.EMPLOYEE WAS WEARING STEEL TOED BOOTS.

CUTTING DUMP CABLE.HOT CABLE CAME BACK AND STRUCK LEFT ARM BURNING IT.

BAGGING PRODUCT FAN BLEW MATERIAL OFF TABLE IN EYE

WIND BLOWING EMPLOYEE DOING VERTICAL CUT WITH TORCH LEFT HAND SLIPPED & TORCH CAUGHT IN COAT SLEEVE

HE WAS CLEANING PUGMILL WITH AN AIR GUN. SOMETHING GOT CAUGHT IN HIS EYE.

RUNNING A DOZER ON ORE PILE DOOR OPEN WIND BLOWING ORE BLEW IN TO EYES CORNEAL ABRASIONS BILATERALLY

EMPL WAS GRINDING WELD JOINT WITH 9" GRINDER. GRINDER BLADE CAUGHT CAUSING GRINDER TO KICK BACK AT HIM. GUARD ON BLADE STRUCK HIM ON CHIN & NEC K AREA.

FELT SOMETHING IN RT EYE 5/14ON THE WAY HOME FROM WORK HAD BEEN WORKING ON A PUMP USING AN IMPACT WRENCH

ROLLING AN 18 INCH PIPE ON ROLLER WELDING PULLED MUSCLES IN LOWER BACK

EMPLOYEE WAS INSTALLING AN AGITATOR IN DECA PLANT CRYSTALLIZER BODY RIGGING ON WHICH THE AGITATOR WAS BEING HOISTED CAME LOOSE & FELL ABOUT 2-3 FT ONTO EMPLOYEES RT FOOT APPROX 75LB FX THREE T OES

PREPARING TO LEAVE WORK SOMETHING IN EYE, USING IMPACT WRENCH POSS METAL IN HAIR FELL IN EYE

IN MINE PIT WELDING ON PIPELINE. WHILE IN SQUATTING POSITION A PIECE OF WELDING SLAG FELL AND BURNED THROUGH PANTS.

AT THE MILL-EMPLOYEE STATED HE WAS CUTTING WITH A TORCH AND HOT SLAG DROPPED INTO HIS SHOE.

AT BUCKETWHEEL PATIENT STATES WHILE MOVING A MODULE UNIT AND STANDING APPROX. 20 FT FROM A BACKHOE A STEEL ROLLER WHEEL SHATTERED STRIKING RIGHT MEDICAL FOREARM.

EMPLOYEE WAS USING AN IMPACT WRENCH TO LOOSEN THE BOLTS HOLDING A CUTTING EDGE IN PLACE. THE BOLT STARTED TO TURN IN THE HOLE AND HE REACHED UP TO HOLD IT. THE SHARPENED EDGE OF THE BOLT HEAD SPUN IN HIS HAND, CUTTING THROUGH HIS LEATHER GLOVE AND CUTTING HIS LEFT PALM.

STARTING IMPELLER ON PUMP SHIFT.USING BELT PULLEY TO TURN SHAFT.CAUGHT LEFT RING FINGER BETWEEN PULLEY AND BELT.

EMPLOYEE WAS STRAIGHTENING THE TOPS OF FILLED POLYBAGS TO GOT THROUGH THE SEALER. HIS LEFT HAND WAS CAUGHT BETWEEN THE MOVING BAG STABILIZER AND THE STATIONARY STABLIZER VEE BELT.

HH & CO-WORKER WERE USING HYDRAULIC COUPLING PULLER POWERED BY AN ELECTRICALLY DRIVEN PUMP. WHILE PRESSURED UP, A FITTING FAILED AND STRUCK HIS LEFT FOREARM.

EMPL WAS USING AIR LANCE IN PREHEATING COMPARTMENT. WHILE BLOWING OUT HOLE HOT ROCK FELL DOWN RIGHT SLEEVE.

OUTSIDE FAB SHOP-WORKING ON A 72 YARD BUCKET, A CONTRACTOR WAS OVERHEAD AND BEHIND HIM CARBON ARCHING-A PIECE OF HOT DIRT BLEW BACK AND HIT THIS EMPLOYEE'S NECK.

CUTTING CABLE WITH A WELDING MACHINE HOT SLAG FLEW ONTO LEFT WRIST.

REACHING ABOVE MANWAY TO RETRIEVE FLASHLIGHT STEAM & WATER FROM WATER LANCE STRUCK LEFT WRIST.

CLEANING OUT #1 CYCLONE ON #2 CALCINER USING AN AIRLANCE. HOT ROCK AND STEAM GOT INTO THE EMPLOYEE'S GLOVE WHILE HIS ARM WAS STICKING INSIDE THE DUCT ON THE #1 HOT CYCLONE.

EMPL HOLDING PIECE OF PLATE TO BE TACKED UP.WHEN INITIAL ARC WAS MADE BALL OF SLAG ROLLED OFF AND HIT EMPL ON LEFT SIDE OF HIS NECK.

WORKING ON 8200 DRAGLINE WELDING BRACKETS FOR LIGHT FIXTURES. HOT SLAG FELL AND HIT LEFT ARM. THE SLAG BURNT THROUGH THE CLOTHING AND BURNED THE LEFT INNER FOREARM.

HOLDING PC OR IRON FORM WELDER HOT SLAG FELL INSIDE HIS BOOT.

MOVING DRISCO PIPE ON THE #6 PILE, A PIECE OF PIPE HIT THE EMPLOYEE AND THREW HIM IN THE AIR. WHEN HE HIT THE GROUND HE INJURED HIS RIGHT ANKLE.

CUT A METAL PLATE OFF A TRUCK BODY & SET IT DOWN IN THE BED OF THE TRUCK THE PLATE THEN FELL OVER ON THE EMPLOYEES RIGHT FOOT

DRILLING A HOLE THROUGH AN ALUMINUM BOX AND DRILL BROKE TRHU, THE DILL GRABBED AND SPUN DRILL MOTOR.

SITTING INSIDE A TEREX TRUCK,A BACKHOE HIT THE SIDE OF THE TRUCK CAUSING JARRING AND SHAKING OF THE TRUCK.