Search the record

Employee opened a door to clean out screw and piched his fingers when he swung it out. He got 5 stitches on his finger where it was cut. He is expected to get full recovery.

Operator had previous back injury 15 years ago. Operator was driving CAT 350 haul truck on rough road and complains of back pain. Operator is out pending examination and treatment for pain.

slipped in muddy conditions and hit back on tracks of parked excavator.

Operator was driving rock truck on 11-8-07 for about 2 hours. On 11-9-07 at noon he reported to his supervisor that he hurt his neck on 11-8-07 while driving rock truck.

Cut to little finger on right hand while putting a hydraulic pump back on an engine and it caught his finger between pump and engine. Engine was not running. Pump was not running. Unit was shut down and locked out.

Operator was declining the ramp to pit when he hit a pothole, jarring his neck.

Wrench slipped while working on valve and hit employee over the bridge of the nose.

Employee was stepping off loader ladder and claims he twisted right knee. Released to full duty 7/9/07.

EE was using length of pipe to hold tension on screen motor belts with prying motion on mounting frame pulling muscle near rib area.

Changing bearing on conv. belt. While taking old bearing off (515/16) bearing slipped & dropped onto EE's finger pinching it between bearing & frame work. Bearing as approx 15 lb.

EE was working on impact crusher trying to dislodge a piece of steel which was stuck with a pry bar. When the steel broke loose, he hit himself in the forehead.

Employee was splashed with diesel in eye when refueling. Employee has no damage or impairment, and has returned to duty.

Was loosening bolts, trying to take off roller to be replaced with a new one.

EE was changing roller and felt something bite him on right forearm.

While servicing the Cat D400 haul truck, employee fell to ground from the fender of the truck.

AFTER EMPLOYEE REMOVED A PIECE OF WOOD FROM UNDER THE CONVEYOR BELT HE TURNED TO GO TO THE CATWALK TO RESET THE TRIP CABLE. AFTER WALKING A FEW STEPS HE FELT A SHARP PAIN IN HIS CALF OF HIS LEFT LEG.

Dropping belly pan on D8R dozer. Bar slipped and pinched finger against bottom of dozer. 3 stitches in fourth finger, left hand.

While repairing Powerscreen 1400 employee slipped & lost footing. He then grabbed machine to hold his balance & caused injury to his right arm.

Ee was removing a frozen valve 3" to thaw it out once all bolts were removed the valve was stuck in place. He pulled on valve when it broke loose it. He did not have a good grip on it and it fell on his wrist the valve weighed approx. 40 lb.

EE WAS USING A PRYBAR TO MOVE A PIECE OF HEAVY STEEL WHEN THE PRYBAR SLIPPED PINCHING HIS FINGER BETWEEN THE PRYBAR AND A NEARBY I BEAM. ADEQUATE INFORMATION WAS NOT PROVIDED TO DETERMINE REPORTABLE TO THE MAIN OFFICE UNTIL 1-12-06.

Tripple and over water hose and fell on concrete landing on left knee.

While working on grizzly he was bitten by a spider on left leg calf muscle.

Employee was assisting co-worker to weld pipe together. He was not wearing safety glasses or safety shield to cover his eyes so he suffered welder's flash. He did not see a doctor but missed one day of work and then returned.

AFTER BEING LOADED WITH SAND, DRIVER WAS CLEANING THE TAILGATE WHEN THE TAILGATE FELL CATCHING HIS RIGHT INDEX FINGER BETWEEN THE GATE AND THE TRUCK BODY.

While stepping down off D6 dozer he slipped and fell.

Ee was assisting mechanic & dragline operator in changing dragline cable. Ee claims pain in lower back, reported to foreman on 7/28. Stated it will be ok in a few days, reported to work 7/29 & 7/30. About 11:00 a.m. on 7/30 ee advised he wanted to leave early to see doctor.

TRYING TO ADJUST FLASHING ON HOPPER BELT, PRYBAR SLIPPED & HIT HAND ON FRAME OF CONVEYOR.

WELDING SAND PIPE A.M. SAND OR METAL WENT INTO EYE. WAS WEARING ALL SAFETY EQUIPMENT. HOOD AND SAFETY GLASSES.

WHILE TRYING TO DISLODGE ROCK FROM CHUTE WITH BAR HIT THUMB BETWEEN BAR AND CHUTE. BROKE RIGHT THUMB.

PUTTING BELTS ON CRUSHER GOT LEFT INDEX FINGER BETWEEN BELT & SHEVE, CUT TIP OFF FINGER.

EE WAS GETTING A SAMPLE OF #8 GRAVEL FROM THE STOCK PILE AT PLANT IN A THREE GAL BUCKET AFTER PUTTING APPROX 15 OB OF GRAVEL IN THE BUCKET HE LEANED OVER TOOK A COUPLE OF STEPS WHEN HE FELT A SHARP PAIN IN HIS BACK.

EE WAS TRYING TO STRAIGHTEN A BENT SPUD BAR BY PULLING IT AGAINST THE BEND HE PULLED TOO HARD & HURT HIS BACK.

WHILE CUTTING CONVEYOR BELT CUT MIDDLE FINGER ONLEFT HAND. REC'D 3 STITCHES

PULLED BACK MUSCLES WHILE SLIPPING OFF LADDER. HAD MUD ON HIS BOOTS.

WHILE LOADING WATER TRUCK HE WAS UNCOUPLING HOSE& COUPLING HIT HIS HAND & SPRAINED FINGER.

EE WAS ENTERING HIS TRUCK TO START SHIFT WHEN HIS FOOT SLIPPED OFF THE STEP INTO HIS TRUCK. HE LOST HOLD WITH HIS RIGHT HAND & TWISTED HIS BACK. STEPS WHERE WET FROM HEAVY RAIN.

GOT OUT OF MY CAR AFTER CHECKING THE FUEL LEVEL IN THE FUEL TANK. MY FOOT WENT OUT FROM UNDER MEON THE SNOW AND I LANDED WITH MY LEFT LEG UNDERNEATH ME.

CUSTOMER ON MINE SITE TO GET A LOAD OF GRAVEL BUT BEFORE DOING SO HE RAISED THE BED OF HIS TRUCK TO CLEAR IT OF DEBRIS. THE BED WAS UP APPROX 18" TO 24" WHEN A PROBLEM WITH THE HOISTING MECHAN ISM CAUSED THE INJURED TO REACH IN BETWEEN THE RAISED TRUCK BODY AND THE TRUCK FRAM (THE TRUCK BODY WAS NOT BLOCKED AGAINST MOVEMENT) WHEN THE TRUCK BED FELL ON HIS ARM.

OPERATOR CLIMBED OFF LOADER TO WASH BUCKET OUT AND SLIPPED ON LOOSE GRAVEL AND TWISTED LEFT ANKLE.

REMOVING WEDGED ROCK FROM JAW CRUSHER USING SPUD BAR. COWORKER LOST GRIP ON SPUD BAR, STRIKING EMPLOYEE IN HAND. THE SHAFT OF THE SPUD BAR FIRST STRUCK HEAD CAUSING HARD HAT TO FALL OFF EXPOSI NG HEAD WHEN BUTT THEN STRUCK HEAD.

WASHING OUT CHUTE, BIG ROCK BOUNCED OUT OF SHAKER HIT RIGHT HAND, PALM REQUIRING STITCHES.

PULLING ON WRENCH TO GET TIGHT BOLT LOOSE.

EMPLOYEE GOT OUT OF VEHICLE AND SLIPPED AND FELL ON ICE AND TWISTED RIGHT ANKLE, WAS TAKEN TO HOSPITAL FOR X-RAYS TO FIND TIBULA WAS BROKEN.

EE STOPPED TO TALK TO EXCAVATOR OPERATOR STEPPEDOVER A SMALL BERM WALKING BACK TO THE TRUCK CAMEDOWN ON FOOT WRONG & TWISTED ANKLE

EMPLOYEE WAS STEPPING DOWN FROM TRIAXEL WHEN HISFOOT PLANTED ON UNEVEN GROUND WHICH TWISTED HIS RIGHT KNEE AND BACK. EMPLOYEE FINISHED OUT HIS SHIFT.

EE WAS LOSENING BOLTS ON THE LID OF PRIMARY CRUSHER TO DO MAINTANCE INSIDE WHEN THE WRENCH HE WAS USING SLIPED OFF CAUSING EE TO LOSE HIS BALANCE AND FELL BACKWARDS APPROX. 3 FT LANDING ON A S UPPORT TOWER FOR THE CRUSHER LID WHICH INJURED HIS LEG HE CAUGHT HIS FINGER TRYING TO STOP HIS FALL.