Search the record

EE was removing large rock from catwalk and smashed finger between handrail and rock. The EE was wearing gloves.

Tech was working on installing new piece of glass, when they were pulling they hit their front tooth and knocked it out

Cut on left pointer finger.

Employee was carrying cutting edge and tripped causing a laceration to the palm of the left hand that required three sutures.

EE was cutting zip tie off end of "down the hole" measuring tape. Cutting away from themself. When the zip tie was cut the knife became uncontrolled and cut another EE. The cut was in EE's hand. The cut required 6 stitches.

Employee was performing maintenance on conveyor when employee injured elbow

Miner was closing a leaking water ball valve when the valve assembly disconnected from the mount striking the miner in the forehead.

Employee was walking under a conveyor when a rock fell from the conveyor striking EE above EE's upper lip. Ee was wearing hard hat and eye protection.

Employee was changing a return roller on conveyor 2 when EE injured EE's left pinky finger. EE was wearing gloves at the time of injury.

The employee was leaving EE's desk when EE struck the corner of an open desk drawer with EE's leg

EE was walking in the surge tunnel and saw a snake. EE turned around to get away from the snake and in the process twisted their right ankle.

Employee was changing a 60 inch conveyor idler when right hand was pinched between the idler and the frame resulting in a laceration requiring 6 stitches.

Employee was using a utility knife to cut skirtboard rubber and the knife slipped and cut employee's left thigh.

Employee was operating a 730 Caterpillar haul truck when ee felt pain in back.

Employee was operating 772 haul truck and the employee smashed middle and ring finger on right hand between the frame and the seat.

Pulling a cable along the framework of conveyor and stepped in hole in grating. Associate fell and impacted knee, back and arm on grating.

A metal cover fell down and struck employee on the right side of the face/jaw as ee held the ladder for another employee to perform the work.

Ee was lifting toggle rods above head when ee felt a pain in right shoulder. EE was placed on restricted duty.

Employee was hitting a striking wrench with a 2 pound sledge hammer and inadvertently hit left hand thumb.

Employee was using a razor knife to cut skirt rubber when he accidentally cut his left wrist.

Miner was performing routine maintenance on a conveyor to remove gear reducer. Miner sprained right ring finger while doing so.

Cut right hand ring finger while exiting corrugated metal building.

Lost balance after lifting 55lbs of flocculant. Injured back.

Employee injured back trying to turn bucket wheel with the assistance of other employees during bucket wheel installation. Accident was not reported until 5/7/13.

Ee was removing pin on 972G loader. The bucket and link were removed. Ee was pulling pin out of the top z-bar link where it attaches to the tilt cylinder. Ee pulled pin out and the z-bar shifted because pin was slightly over center. The Ee's thumb was caught between the head of the pin and the bucket leveler bracket.

Ee lost footing while installing j-bolt on screen. Ee slipped scraping his right shin and hit his right hip on 2" channel piece of channel.

EE was assisting in removing pin from a Caterpillar 944 bucket when the pin came out unexpectedly and crushed left hand index finger between pin and bucket.

Ee was pulling on water hose to wash off concrete pad when he stated he felt his wrist pop and noticed pain.

Employees left foot slipped from walkway platform to step causing shin to contact step. Conditions: flat walkway with one step up to another level.

Employee was changing screens. Sprained wrist.

Ee was using sledge hammer on plate to press large bushing into loader (equipment) link. A small piece of metal came off of plate and punctured Ee's left forearm.

Employee was installing plates on track crusher. Employee was distracted and plate struck the employees hand on the guardrail. Right hand received small deep abrasion.

Employee was trimming grass around the main gate when he hit a bee/wasp nest. Employee was stung several times. Employee was sent to the doctor as a precautionary measure.

Employee sprained ankle climbing off equipment after a pre-shift exam.

Employee was clearing off a screen that was overloaded with material, when a rock fell off and struck his right foot.

Employee was replacing panel on bottom deck of screen. Employee was removing old screen, when employee felt a pull in his lower back.

Employee made contact with a hot piece of metal (area that he previously welded) when reaching for welding rods resulting in a second degree burn on his arm. Burn became infected on the evening of 4/29/09 and employee sought medical treatment.

Employee was installing a 4" valve on a waterline when some loose material slid down the slope and hit the employee's ankle.

Employee was using sledge hammer to remove pins from cylinders on a cone crusher. Employee stated right hand was hurting yesterday evening after he left work. Employee reported the injury on 4/15/09 at beginning of shift.

Employee lacerated his thigh with a power tool while cutting screen cloth. Injury required five stitches and medication for infection.

Employee sprained ankle on unstable ground (loose gravel) while walking down stairs at scale house.

Employee was turning over the cutting edge of a 972G CAT loader. As he was loosening the right nut/bolt of the cutting edge the center bolt broke free causing the edge to drop suddenly to the ground on his right foot.

Bolt was being knocked from pin on EC 240 LR Excavator. A punch was struck by another employee to remove pin when the working end of punch broke off and hit employee in the neck.

Employee was installing electrical wire. Employee was attempting to roll wire reel to the side when reel slid and pinched his thumb between reel and pipe.

Employee was conducting preshift examination on his front end loader, when he missed/slipped on the first step. Frost was on the ground and equipment.

He was tubing holes so that they would not fill up with water if it rained and was cutting them to fit holes and he accidently cut his leg.

The injured miner was dismounting a haul truck when he slipped and started to fall. As he was falling he was able to regain his grip with his left hand and the weight of his body caused him to strain his left shoulder.

While walking with his supervisor, the injured miner slipped on a rock, caught himself mid-fall, and felt a sharp pain in his lower back.

Employee was removing parking brake assembly from heavy equipment when the parking brake assembly shifted and pinched the right ring finger between the parking brake and the frame of the machine.

The injured miner failed to maintain three points of contact and slipped while climbing the ladder of an intregated tool carrier and the tailbone of his lower back contacted the machine. He reported this accident on the following day and refused medical treatment. Medical attention was requested on 3/14/07.