Buscar en el registro

Employee was removing the hyd. tank cover on the ex1800 Hitachi excavator. He dropped the cover on his left index finger. Fractured (small) to end of finger.

Employee was repairing the air conditioner on the PC1800 Komatsu excavator when his finger came in contact with the air conditioner fan blade.

Employee was removing a fuel pump on the service truck. The pump slipped and mashed/cut his thumb between tank and pump. (This was a Lincoln air pump located in one of the fuel tanks on the service truck bed).

Employee was repairing the transmission on the 992-C loader. The cover slid and cut the top of his left index finger. (Required stitches).

EE was changing the dust filters on drill #514. He failed to move his arm and the filter dropped out and struck his arm.

Employee were setting a new reel of drag cable dragline cable with a 992 c loader into the cable stand. As reel was lowered into stand employee got his left hand caught between the pipe holding the reel and the cable stand. Pinched palm of left hand.

Employee was moving the power cable feeding the 1300 BE dragline in order for the machine to walk back on the bench. He bent over to hook the cable to the machine & strained his lower back. *Did not go to Dr. or loose time until 12/02/05.

EMPLOYEES WERE REPLACING AN ELECTRIC MOTOR. INJURED EMPLOYEE WAS GUIDING THE MOTOR ONTO THE MOTOR STAND (FRAME) AND CAUGHT HIS RIGHT HAND BETWEEN THE MOTOR AND STAND. LACERATION REQUIRED 2 STITCHES. (EMPLOYEE WAS NOT REQUIRED TO WORK 11-5 AND 11-6).

Employee was changing the dust filters on the SKF Reed drill. One of the filters was stuck. When it came loose it fell on his right wrist causing his wrist to strike the frame of the dust filter housing.

During dragline repair, employee was lifting a metal house roller pin, strained abdomen. Later determined to be abdominal hernia. Did not loose time until 8/29/05 for hernia repair.

Employee was conducting pre-shift exam on loader. he was on the ground and turned around striking his left elbow against the side of loader.

EE HAD HELPED THE MECHANIC REMOVE AN IDLER FROM A D-10 DOZER. HE WAS LOADING THE JACK INTO THE MECHANIC'S TRUCK WHEN THE JACK SLIPPED AND CAUGHT HIS FINGER BETWEEN THE JACK AND EDGE OF THE VEHICLE LICENSE PLATE. LACERATION TO RIGHT INDEX FINGER (REQUIRED STITCHES.)

EMPLOYEES WERE REPLACING A DUMP CABLE ON 1300 DRAGLINE. WHEN BAND HOLDING COILED CABLE WAS CUT, EMPLOYEE WAS STANDING IN WRONG PLACE. END OF CABLE SLAPPED EMPLOYEES LOWER RIGHT LEG CAUSES BRUI SES AND CONTUSIONS (NO FRACTURE).

2 CUTS TO BACK OF RIGHT HAND, RESULTING FROM GETTING HAND CAUGHT BETWEEN PIECE OF PLYWOOD AND SHARP METAL EDGE (CREATED BY CUTTING TORCH) WHILE HELPING WELDER REMOVE PLYWOOD FROM WORK AREA.

EMPLOYEE WAS REMOVING RETAINER RING (LARGE) ON DRAGLINE (680 W). ONE HAND SLIPPED ALLOWING ALL WEIGHT TO BE TRANSFERRED TO OTHER HAND (LEFT). ARM WAS RAISED AND TWISTED SLIGHTLY DISLOCATING LE FT SHOULDER.

EMPLOYEE WAS LI0TING A TRAIL CABLE (DRAGLINE) TO HANG ON A HOOK SO THAT MACHINE COULD TRAVEL.

EMPLOYEE WAS PL5CING ROCKS IN SPILLWAYS AND DAMS FOR WATER CONTROL ON RECLAIMED AREAS. BACK INJURY IS UNDETERMINED.

RESTRAINING CHAIN HOLDING BELLY PAN OF D9L DOZER SLIPPED OR BROKE ALLOWING PAN TO FALL EMPLOYEE RIGHT HAND WAS UNDERNEATH PAN LACERATION AND BRUISES TO THE INDEX AND MIDDLE FINGER WERE SUFFERE AND THE TENDON OF THE INDEX FINGER WAS PARTIALLY SEVERED.

BACK STRAIN CAUSED IN MOVEMENT OF DRAGLINE TRAIL CABLE

EMPLOYEE WAS CLIMBING ON A DIESEL MOTOR AND HE CUT HIS HAND ON A HOSE CLAMP