Buscar en el registro

EE was wearing work gloves and dropped the fuel nozzle which landed on right 5th digit causing a laceration and fractured 5th digit. EE is being sent to hand specialist for medical treatment.

EE was removing drive line on MP0227 so EE could repair parking brake. EE was knocking out U joint when a piece broke off and stuck in the left wrist. Sent to clinic and had piece removed and was given tetanus. Removal of foreign body. 30CFR50.20-3(a) 1(ii) EE was wearing PPE.

EE was unplugging the air hose from the hose reel, when EE's right hand was injected with metal, dirt, and air. EE was taken to the Hospital for care

Employee was changing a bin pulley on MJ-0201. When the pulley got stuck between two uprights. EE pulled on it causing it to swing back and strike EE's left hand causing restricted duty.

EE was checking the oil in a Komatsu WA600 when right hand struck the engine compartment door. 24-48 hours later EE was diagnosed with cellulitis of the hand. EE was prescribed Rx to treat the cellulitis.

Lifting a light fixture from shoulder height to ground felt a pop in lower back. Fixture weighed 30 - 40 pounds.

Employee was adjusting the mirror in his 924 Loader, and the lens broke cutting his right wrist. It was treated with first aid the next day reported he went to doctor to have it check. They cleaned it, and applied steri-strips for closure. i.e. similar to butterfly bandage.

EE was pushing up on conveyor roller and felt a sharp pain in right shoulder and elbow. Ice was applied and sent to OMP for medical evaluation. He is on restricted duty.

Employee was replacing compressed gas cylinders on the Oxy-fuel torch section on welding trailer, and smashed his fingers between the new bottle and the structural steel of the support rail of the trailer.

Employee went to lift a screen to help install screens and cut his thumb on the edge of the screen. Gloves were available and he chose not to wear them.

EE was filling and lifting 5" bags for powder truck. Felt twinge in back.

Employee was opening an aluminum can of welding rods and his hand slid across edge of can lacerating his hand requiring three stitches.

Employee was cut on his left hand while greasing a bearing on a cone crusher.

EE is our dredge operator and a mechanic, and he was repairing an outboard motor on the Jon boat when it "snapped" or broke free from boat's connection and his left hand was in the path of the fly wheel when the motor rose up/throttled out of the water during mechanical repair.

Equipment number MQ-0667 developed a hydraulic leak. Upon opening a spiral boom cover, hydraulic oil injected into the employee's left fifth digit.

While employee was climbing up his truck steps, he felt a sharp pain in his right groin.

Employee was changing a broken bucket cylinder. He was sprayed with hydraulic fluid on his body. While finishing the process of the job, hydraulic fluid dripped into his eyes. He was wearing proper personal protective equipment while the work was being done.

Upon the completion of cleaning with a wire wheel attachment, EE had discomfort in his right eye. He was sent to the doctor and a foreign body was removed. EE was given prescription eye drops.

Employee was helping carry a screen. The screen slipped from his hand cutting his left index finger.

WW was washing out around MK-509 feeder when a piece of mud got into his left eye. EE was wearing personal protective equipment.

Employee bent over to pick up a cable to hand it to someone. When he grabbed the cable and stood up, he felt something pull in his lower back.

Employee was removing a seal from a brake head. His hands slipped off while pulling on the seal, cutting both left and right thumbs.

EE was hanging conveyor belt for an air wall using an air impact and noticed an irritation in his eye. EE was wearing all appropriate PPE including safety glasses.

EE was assisting in the switching out of barges when the barge winch brake was left on, and the boat pulled out with the cable and brake still on. The cable broke and whip lashed back into EE's lower legs. Life Flight was called.

EE was performing accumulator check and steering adjustment, and bled off the pressure. He then removed the valve which still had pressure and it punctured his right arm. He is on light duty with restrictions.

Employee was removing a loader cutting edge out of the 924 loader bucket and smashed his finger. Open fracture and bruised nail bed.

Employee was removing barge wire off of cavel on dock when the wire had flipped under tension and jerked his arm straining his wrist. Wire rope has lay memory and when it stuck in clete the energy in the tensioned wire rope caused it to roll while he had it in his grasp. Doctor indicates strain.

2 ee were replacing cutting edge of Hitachi bucket and dropped the cutting edge on ee 4/5 phalanges smashing them. He had it braced with cribbing and it moved dropping 3 inches onto the deck of the dock. 11 sutures.

Employee was handling material to line a chute and felt discomfort in his lower back. He was sent to OccMed for evaluation and was diagnosed with low back strain. Returned to work with restrictions.

Employee was assisting with putting the sheave back on the screen shaft. Employee's finger got caught between the sheave and the shaft resulting in a laceration and a fracture on the right middle finger.

EE had a part of a bucket get caught on a bucket elevator, and the part slipped hitting him in the mouth. They were jogging (maintenance)the elevator looking for a pin that had lost its cotter key to repair it. The wear of the pin caused the bucket to move lodging under a lip of the elevator and jogging it caused the bucket to spring hitting him in the mouth as he watched it.

Employee climbed up in his truck after doing some work at the primary while the plant was down and when he sat down his back/right shoulder was hurting. Employee did not report this accident until 1/25/2012.

Employee was digging out a plug up in the hopper when he felt a burning sensation in his back.

EE was moving a fan in the dry dock area when dust/rust blew from surrounding fans around his PPE and landed on his eye. He naturally rubbed it which resulted in a small scratch on his eye. It was removed and he was prescribed an prescription antibiotic. Released immediately to full duty no restrictions.

EE was shoveling to clean up area. He pulled something in his back but is unsure of exactly when it happened.

EE closed the door of the loader on his thumb and smashed it.

Employee was lifting a gate up under crusher and pulled a muscle in his lower back.

Employee was assisting with a maintenance task of re-assembling an auger when he lifted a blade and felt a discomfort in his abdomen that did not go away. He was sent for medical evaluation and has been diagnosed with an inguinal hernia on his left side. He has restrictions that can be met as of now, and is being scheduled for surgical repair.

EE was getting ready to put the right rear wheel hub on an R-85 haul truck. As he picked up a stack of shims he cut his right little finger on a 0.005 thick shim. He went to the doctor and received stitches.

Employee was replacing a wear plate inside MI-0503 when the plate slipped he instinctively tried to catch it. The plate weighing 70# smashed his finger (3rd digit on left hand)between the plate and the ground. He was immediately sent for medical evaluation.

EE is claiming an injury that supposedly occurred back in October or December that involves a strain to his left shoulder. A sprain occurred while opening flapper gate on rip rap flapper lever hopper. It is being investigated. We were first notified on 2-14-11 when injury supposedly happened on 12-6-10. I will forward any additional info as we are notified.

EE was retrieving a piece of expanded metal out of rack, and caught his right calf on a piece of metal. It cut through his jeans, and lacerated his leg requiring a few stitches to close the wound. He was wearing all required PPE.

Employee was assisting with changing screens, and while removing screen from hoist gravity brought the screen down striking the back of her left hand resulting in a laceration needing sutures to close the wound. Gloves are provided but were not being used.

EE was installing a troughing roller and he smashed his fifth finger on right hand between frame of conveyor and roller. He had assistance available, but tried to perform job without assistance, resulting in a smashed finger. He is on light duty.

EE released the locking mechanism on the tag line for the cable crane bucket, and it uncoiled and it violently struck him in the left shoulder / shoulder blade a couple of revolutions. He was wearing all his equipment and a life jacket took a majority of the energy. He was sent to doctor for examination and treatment for some bruises/abrasions.

Shoveling rock with a long handle shovel and strained his back.

Stepping out of backhoe to the ground. When he stepped to the ground, he twisted his ankle, resulting in a sprained left ankle.

removing hydraulic swivel from trackhoe. One bolt was in a hard to reach area. when the bolt came loose he hit his elbow on the swivel causing a bruised elbow

hooking up a lift chain to remove a loader bucket. The loader bucket had a burr on it that caused a cut to his right little finger, requiring sutures.

Removing frozen material from a return roller guard. The material fell and struck him on the left foot striking his steel toed boot causing a broken big toe.