Buscar en el registro

IW & coworker were installing a roller and IW pinky got caught underneath, causing a laceration and fracture.

IW pulled a tool tray out and strained EE's back.

IW was performing maintenance; carrying a guard and EE pulled a groin muscle.

Retrieving a tool from truck bed. 5" drill bit slipped out of hand landed on left foot just above steel toe tip of boots.

IW working on a tarp and little finger got caught between rope and shaft.

Worker thought digging bar was clear of two pipes, and began to lift and walk away with it. The bar got jarred and as EE pulled, the motion over extended EE's shoulder. Worker denied care at time of incident. EE worked at full capacity until EE requested and went for an initial evaluated on 11/23/22.

Injured worker was struck in the head when a drum dolly became dislodged.

Employee was putting roller in and was struggling to get the roller to stand up next to another roller and while doing so, the hand rolled into the roller and got pinched between the two rollers.

Lifting rock out of the cone crusher chute. It slid out and ripped skin and nail of right pinky finger.

Employee said that they were working down in the hole, there was a roll of plastic liner on a rack being. As they were rolling out the plastic liner, the plastic liner slid down the rack and crushed employee's left hand between the liner and the rack.

EE was working on the tail pulley adjuster to provide slack for the conveyor. While removing the plug from the adjuster, the plug struck EE's left index finger, palm and thumb.

Employee was climbing up the steps to the Haul truck while holding on to the hand rail. Employee heard a pop in right middle finger.

A piece of plate steel hit and bent thumbs backward.

Throughout the day when working ee felt calf muscle giving out. When ee stepped into truck to leave at end of work day, ee heard a pop and felt intense pain.

Employee was changing screens and the screen fell, causing a laceration to left middle finger.

He was pulling a roll a way chute closed. He strained his upper back.

Employee was welding a loader bucket and took his gloves off to use a sledge hammer and accidently grabbed the hot spot on the loader bucket. He received a second degree burn on his right hand palm.

Lifting 12" x 6" steel beam that was 8' long into loader bucket

Employee was installing a steering wheel lock on a loader and lifted the ram of a 20 ton porta power and tore something in his left elbow.

Changing rollers at the Secondary crusher area on the 2-A (S-3) conveyor. While removing old roller frame, twisted left shoulder, treated at WorkNet for shoulder injury from time of accident. Went for arthroscopic surgery 7-30-12, had been working up until now.

Employee said he was attempting to roll a rock off to the side of the haul road.

Employee was removing a flip gate at the wet screen of the crushing plant and strained his lower back

It was cold, raining and damp, EE stepped on wet platform of his trailer. He slipped and fell, twisting ankle.

Employee was setting a pin press tool into its case and the press rolled onto his left pointer finger and punctured it.

EE was cleaning out chute under D-1 scren behind primary crusher on top of D-2 conveyor.

Employee was changing a cable on a dragline and a strand of cable punctured his right forearm. He was sent to the emergency room for a tetanus shot.

The injured employee and another employee were carrying a piece of angle iron. One employee dropped his end of the iron causing it to cut the other employee's hand. The laceration required stitches.

Climbing onto truck #060076 to check the fluid levels before starting it for the day, while climbing up ladder he felt a twinge on his right shoulder upper arm.

Employee slipped from a ladder on a loader and sprained his ankle.

Working on primary crusher he dropped his wire brush onto D4 conveyor. He climbed down to get the wire brush. As he climbed out and off the conveyor he went to jump over the railing and his right knee locked up & he could not bend it.

On 11-23-05 employee reached for truck door and banged finger on door. On 12-13 employee went to personal physician & was given a prescription. On 12-27-05 he went back to physician and was put out of work for six weeks to prevent further dust exposure and cure finger.

Employee caught foot between two pieces of steel. Twisted right knee.

Employee was cleaning a wall air conditioner and cut his left index finger.

EMPLOYEE WAS HELPING PULL A 400 LB. PART (REDUCER) OFF DELIVERY VAN AND STRAINED HIS BACK.

REPAIRING DRIVE SHAFT IN A 988 LOADER, STRAINED LOWER BACK.

BLOCK SLID OFF PALLET DUE TO ICE ON BLOCK WHICH HIT EE IN THE LEFT SHIN. HE WAS MANUALLY HANDLING BLOCKS ON PALLET ON FORKLIFT.

EMPLOYEE WAS LIFTING A WINDOW ON A DRAGLINE, LEFT FOREARM BECAME SORE.

CLIMBING AND WALKING ON CONVEYORS, CRUSHER, AND SCREEN DECK.

EMPLOYEE PINCHED HIS FINGER BETWEEN A SCREEN ANDSCREEN CLOTH. INJURY REQUIRED STITCHES.

INJURED WAS REMOVING A SPROCKET FROM THE SHAFT OF AN APRON FEEDER TO FACILITATE THE CHANGING OF THE SHAFTS BEARING, INJURED HIS LOWER BACK. HE WAS IN A BENT OVER POSITION AND WHILE REMOVING A HEAVY SPROCKET FROM THE SHAFT, TWISTED TO THE SIDE. HE REPORTEDLY FELT A SHARP PAIN IN HIS LOWER BACK WHILE PERFORMING THIS ACTIVITY.