Buscar en el registro

Employee was repairing a swamp cooler when EE injured EE's left-hand pinky finger needing stitches.

Employee was cleaning the firebox at the dryer and had his fire boots on. Once cleaning was completed and employee removed his fire protective boots he noticed a blister on bottom of right foot.

Working with another EE on pump. EE placed a bar to hold sheave and the other EE asked him to move the bar so he could check the threads on the shaft. When the other EE tried to screw on the impeller the EE had not replaced the bar and tried to hold the sheave by the belts. EE's fingers were caught between the drive belt and sheave.

Dark, windy night. Employee was washing sand from dryer pad with pressure hose. Hose became kinked and the employee tried to move hose around to get the kink out. Hose was full of pressure and he lost control. The nozzle portion came up and struck employee in the face.

Unknown. EE finished his shift, went home and later found both hands swollen. EE was fine and in no pain while at work. EE had been painting and cleaning parts with WD-40 while at work.

Employee went to check water in radiator. Hot water spewed out, burning him.

While removing caustic line that goes to the seal tank some caustic got into his boot. While removing protective equipment EE failed to wash his gloves before removing his boots or suit & goggles. Caused chemical burn on right foot. EE told supervisor @ 8:00PM that this happened. Super visor told him to remove boot.EE told supervisor not a problem only small amount.

EE WAS OPERATING LOADER. SAND PILES ON ROAD. ALSO SAID HE HIT HIS HEAD WHEN HE WENT TO GET OUT OF THE CAB.

EE was draining oil from equipment. When he removed oil plug, hot oil, sprayed onto his face causing oil to go into eyes.

WHILE ATTEMPTING TO REPLACE THE DRIVE BELT ON THE ASH SCREW BY ROLLING THE NEW BELTS, EMPLOYEE'S FINGERS GOT CAUGHT BETWEEN THE BELTS & THE SHEAVE CUTTING HIS MIDDLE & RING FINGER ON RIGHT HAND.

WHILE SHOVELING OUT FIREBOX, EMPLOYEE SWUNG BACK TO GET ANOTHER SHOVELFULL WHEN HE HIT THE SIDE OF THE FIREBOX ON A SHARP EDGE CUTTING HIS LEFT HAND.

EE WAS REPLACING STARTER IN HAUL TRUCK. THOUGHT HE HAD BOLT STARTED WHEN STARTER FELL AND SMASHED HIS FINGER.

WORKING ON ROD DECK COUNTER WEIGHT CROSS MEMBER HAD SHARP EDGE AND CUT LEFT WRIST.

EMPLOYEE PINCHED RIGHT HAND WHILE WORKING ON FORK ON FORKLIFT MAST.

EMPLOYEE WAS CHANGING COVERALLS AND HIS HARD HATOFF WHEN HE STOOD UP HE HIT HIS HEAD ON TRACK ADJUSTER.

LIFTING A GEAR BOX FROM THE GROUND TO A PICK-UP BED.

EE WAS CHANGING SWITCH ON RAILROAD TRACKS. HE STOPPED OVER TO RAISE HANDLE ON SWITCH AND AS HE WAS MOVING SWITCH HIS BACK STARTED TO HURT.

ASSISTING IN REPAIRS WHEN A 2" HOSE RELEASED FROM HOOK ABOVE AND FELL ON HAND. THIS WAS HER LAST DAY AT WORK.

EE WAS OPENING THE TOP DOORS ON RAILCARS. THE CUFF ON HIS GLOVE CAUGHT ON THE EDGE OF THE DOOR AS IT WAS WALLING OPEN. THE PALM OF HIS HAND WAS PINCED BETWEEN THE DOOR & THE TOP OF THE CAR.

EMPLOYEE WAS WASHING RAILCARS. HE CLIMBED DOWN INSIDE CAR TO RINSE OFF THE ROOF. HIS FOOT SLIPPED OFF THE RUNG OF THE LADDER AND HE STRETCHED HIS SHOULDER MUSCLE WHEN HE HELD ON WITH ONE ARM.

CLOSING TOP DOOR ON RAIL CAR, DOOR BOWED UP AND WOULD NOT CLOSE. STRAINED LOWER BACK.

WHILE MOVING DRISCO PIPE FROM #26 PICK UP TRUCK TO #23 CREW CAB PICK UP TRUCK. HE STRAINED HIS LOWER BACK.

EE & EE WERE CHANGING A TRACK ROLLER ON A D9 DOZER EE WAS ON H IS KNEES UNDER THE DOZER LIFTING ON ONE END OF THE ROLLER TO MOVE IT INTO POSITION WHEN HE HURT HIS BACK

HE WAS PERFORMING NORMAL MAINTENANCE, HANDLING METAL AND WORKING ON A SHORT BELT. HE GOT A PIECE OF METAL IN HIS EYE.

HE WAS GETTING OUT OF A HAUL TRUCK & HIS HARD HAT HIT THE TOP OF THE DOOR FRAME & JAMMED HIS NECK DOWN

HE HAD THE GREASE HOSE ON THE LUBE TRUCK PULLED OUT GREASING A LOADER. THE CATCH ON THE HOSE REEL CAME LOOSE WINDING THE HOSE UP. IT GAVE HIS RIGHT ARM A JERK, TWISTING HIS ELBOW.

WHILE HE WAS WIPING OFF A TRUNION ON A LOADER HE GOT A METAL SLIVER IN HIS CENTER FINGER ON HIS RIGHT HAND.

HE WAS CLIMBING UNDER GRIZZLEY AND HE BUMPED HIS LEFT KNEE ON A CROSS MEMBER.

HE WAS CHANGING ROLLERS ON A CONVEYOR. WHEN HE WENT TO THROW THE OLD FRAME DOWN, IT HIT AN ANGLE BRACE ON THE STRUCTURE AND HIS FINGERS WERE BETWEEN THEM. THIS CUT HIS INDEX AND MIDDLE FINGERS ON HIS RIGHT HAND. HE ALSO GOT A PIECE OF METAL IN HIS FINGER.

HE WAS LIFTING A PUMP OUT OF A BARREL AND PULLED A MUSCLE IN LOWER BACK.

INSTALLING V-BELTS ON PULLEY ,RING & LITTLE FINGERS GOT CAUGHT BETWEEN BELT AND PULLEY RESULTING IN LACERATIONS AND BROKEN NAILS.

WHEN REMOVING V BELTS FROM WET SCREEN MOTOR SWINING MOTOR BASE SUPPORT BROKE OFF ALOWING MOTOR TO FALL STRIKING EMPL'S LEFT FOOT.

AGGRIVATED A PRE-EXISTING HERNIA CONDITION WHILE OPENING DOOR ON RAILROAD CARS.

CHANGING BEARING ON SCREEN FEED CONVEYOR GOT SMALL PIECE OF METAL IN EYE.

EMPLOYEE WAS REMOVING A COLLAR FROM PULLEY SHAFT. ANOTHER EMPLOYEE PUT A TENSION ON PULLEY WITH COME ALONGS SHAFT PULLED THROUGH PULLEY FROM TENSION APPLIED, CATCHING J LEFT MIDDLE FINGER BETW EEN COLLAR & BEARING CUTTING OFF TIP OF FINGER BEHIND NAIL.