Buscar en el registro

Employee was removing charger cables from bobcat battery, when his right little finger contacted the fan blades causing a dislocation. A splint was applied.

Employee was removing a piece of brattice cloth from the heavy media vessel when he felt a sharp pain down his right leg and in his back.

Moving a welding machine using a forklift. He stopped the forklift, set the parking brake, and turned it off after he lowered the welding machine onto the ground. As he was unhooking a stabilizer chain the welder shifted on the ground pulling the chain and the tip of his index finger was mashed between the chain and the forklift mast. Was wearing leather gloves.

Employee was moving a piece of grated flooring material and it brushed against his forearm, causing a laceration.

Employee was removing a guard from a pump in the basement area when it shifted and the corner hit his left arm causing a gash requiring stitches.

EE WAS FITTING 14"PIPE, 20"LONG, WHEN HE SLID THE PIPE BACK TO CUT THE PIPE, THE PIPE STARTED TO FALL AND HE MOVED TO STEADY IT. AS HE DID SO, HE EXPERIENCED BACK PAIN, BUT CONTINUED TO WORK UNTIL 7-31-02. (HIS LAST WORKDAY WAS 7-30-02).

INJURED REPORTED FELLING PAIN IN LOWER BACK. NO OTHER REASON WAS GIVEN. NOTE: THIS WAS ORIGINALLY A FILE ONLY, BUT NOW HAS BECOME REPORTABLE AS OF MARCH 15, 2002.

WHILE TRYING TO COUPLE 8" PIPE TOGETHER, EE EXPERIENCED PAIN SPANNING HIS BACK AND RIGHT LEG. EE WORKED UNTIL 3-1-02, BUT COULD NOT DEAL WITH THE PAIN. THIS PROMPTED MEDICAL ATTENTION, AND IT WAS FOUND THAT HE HAD A TORN MUSCLE IN THE SCROTUM. REPAIRS AND RECOVERY ARE UNKNOWN. ORIGINALLYFILED AS A 'FILE ONLY', BUT HAS NOW BEEN DETERMINED AS AN LTA.

EE WAS ROLLING UP TARP ON HIS TRUCK & PULLED DOWN THE TARP BAR TO HOOK UP THE CHAIN & SEEMED TO HAVE CAUSED A LOWER LUMBAR STRAIN IN HIS BACK

EE WAS PULLING A SUMP PANEL UP INTO PLACE WHEN THE PANEL HUNG. AS IT WAS PRYED LOOSE, IT FLIPPED OVER AND CAUGHT HIS PINKY FINGER ON HIS RIGHT HAND BETWEEN THE PANEL AND CHAIN FALL. EE INDICAT ED HE WAS WEAVING METACARPAL GLOVES AT THE TIME.LACERATION RESULTED TO PALM SIDE AND SIDE OF PINKY FINGER.

EE HAD HIS LEFT HAND RESTING ON THE BOTTOM HALF OF THE REFUSE CYCLONE WHILE THE PUNCH PLATE AND SUPPORT WAS BEING CUT OUT AND REMOVED. WHEN THE LOAD WAS RAISED, IT SWUNG AND PINCHED HIS LEFT F INGER AGAINST THE CYCLONE.

THE EMPLOYEE WAS INSTALLING A WEAR PLATE ON AN ACLASS PUMP WHEN THE PALTE WAS CAUGHT ON THE SIDEOF THE PUMP. WHEN HE MOVED THE PLATE IT CAUGHT HIS LEFT HAND BETWEEN THE PLAT AND THE SUCTION LI NE CAUSING A LACERATION. HE WAS TRANSPORTED TO WILLIAMSON MOMORIAL HOSPITAL WHERE SUTURES WERE REQUIRED TO CLOSE THE WOUND. HE WAS WEARING GLOVES @ THE TIME OF THE ACCIDENT.

THE EMPLOYEE WAS TRAINING THE CONVEYOR BELT WHEN THE ACCIDENT OCCURRED. HE WAS LIFTING AN IDLER WHEN HE EXPERIENCED PAIN IN HIS LOWER ABDOMEN. EMPLOYEE DIAGNOSED WITH A HERNIA. SURGERY REQUIRE D TO REPAIR THE HERNIA.

EE WAS LIFTING A COMPRESSED ACETYLENE CYLINDER APPROX 60PDS-WHEN HE REPORTED EXPERIENCING A PAIN IN LOWER ABDOMEN. THE INJURY WAS DIAGNOSED AS A HERNIA TO THE LOWER ABDOMEN. EE UNDERWENT SURG ERY 10/13/97 TO REPAIR THE HERNIA. HE WORKED ON HIS NEXT REGULAR SHIFT FOLLOWING THE ACCIDENT 1ST DAY MISSED WAS 10/13/97 THIS IS A DEGREE 3 CLASSIFICATION 09-HANDLING MATERIAL ACCIDENT

EE WAS UNLOADING A CAR OF GARBAGE FROM A MINE CAR INTO THE BUCKET OF A 988D FRONT-END-LOADER. WHILE PERFORMING THIS TASK, A BONDING STRAP (METAL BAND) CONTACTED THE EE'S RIGHT ARM AND CAUSED A LACERATION REQUIRING SUTURES. EE REUTRNED TO WORK ON THE SAME DAY AND COMPLETED HIS SHIFT.

EE AND A COWORKER WERE ENGAGED IN PLACING TROUGHING IDLERS ALONG THE BELT ENTRY IN PREPARATION FOR A BELT MOVE. THE EE REPORTED EXPERIENCING PAIN IN HIS UPPER BACK. WHILE ASSISTING TO LIFT ON A TROUGHING IDLER. HE WAS UNABLE TO WORK ON 4-23-97 AS A RESULT OF THIS INJURY.

EMPLOYEE WAS REMOVING GUARD TO REPLACE ROLLER ON BELT. AFTER TURNING BLOWER AROUND IT KICKED BACK AND FELL OFF STAND. IN TRYING TO CATCH THE BLOWER WITH HIS HAND, IT BENT HIS WRIST BACK, SPRAI NING WRIST.

EMPLOYEE WAS BUILDING A CRIB. AS HE REACHED TO GRASP A CRIB BLOCK, A CO-WORKER PITCHED ANOTHER CRIB BLOCK AND IT STRUCK EMPLOYEE'S LEFT FINGER RESULTING IN A LACERATION. EMPLOYEE WAS WEARING M ETACARPAL GLOVES AT THE TIME. HE CONTINUED HIS SHIFT. HE THEN WENT TO THE HOSPITAL AND 4 SUTURES WERE APPLIED TO CLOSE THE LACERAITON. MEDICAL TREATMENT ONLY. DID NOT MISS AND DAYS OF WORK.

EE AND A COWORKER WERE ATTEMPTING TO MANUALLY EXTEND SLIDING EXTENSIONS ON ATRS T-BAR JUST PRIORTO BEGINNING ROOF BOLTING OPERATIONS. EE REPORTED EXPERIENCING A SUDDEN PAIN IN HIS LOWER ABDOME N AS HE EXERTED UPWARD PRESSURE. HE COMPLETED SHIFT BUT FAILED TO REPORT ON 10-15-96. THE INJURYWAS DIAGNOSED AS A HERNIA.

EMP WS REMOVING SPEED REDUCER FROM MOTOR SHAFT OF THE CLEAN COAL BELT DRIVE, WHEN REDUCER FELL, STRIKING EMPS LEFT HAND.

EMP WAS OPERATING A JOY CONT. MINER REMOTELY TRAMMING FROM ONE ENTRY TO ANOTHER. STOPPED THE MINER AND LIFTED THE 1 1/2" WATER LINE AND THE TRAILING CABLE TO PLACE THEM ON THE CABLE HOOK ATTAC HED TO THE MACHINE. EMP REPORTED THAT HE STRUCK HIS HARD HAT AGAINST THE MINE ROOF WHEN HE STOODUP WHILE LIFTING THE CABLE AND WATER LINE. REPORTED PAIN IN HIS NECK.

THE EMPLOYEE AND CO-WORKER WERE RECOVERING 60 POUND RAILS FROM AN ABADONEL PANEL. A WHEEL OF A BATTEYR-POWERED SCOOP STRUCK ON OF TH ERAILS INADVERTENTLY CAUSIN GHT ERIAL TO SWING AORUND AND STRIKE THE EMPLOYEE ON THE OUTSIDE OF THE LEFT LEG RESULTIG IN A CONTUSION. THE EMPLOYEE WAS WALKING APPRXO 12' INBY THE SCOOP AT THE TIME OF THE ACCIDENT.

EE WAS LIFTING A 8" PLASTIC WATER LINE OVER ROCK WHICH HAD LINER CRIMPED. PIPE STARTED TO SLIDE DOWN ROCK, CAUGHT EE'S HAND AND SMASHED FINGERS.

EMPLOYEE WAS ATTEMPTING TO SPLIT A HALF-HEADER WOOD BLOCK BY STRIKING IT AGAINST A RAIL.THIS CAUSED THE HALF-HEADER BLOCK TO RICOCHET,STRIKING THE EMPLOYEE'S MIDDLE AND RING FINGER OF HIS LEFT HAND RESULTING IN A FRACTURE TO HIS RING FINGER.THE EMPLOYEE DID NOT MISS WORK AND THE EVENT SHOULD BE CLASSIFIED AS A DEGREE 6 AND CLASS 20.

EMPLOYEE & A CO-WORKER WERE ATTEMPTING TO SUSPEND CONTINUOUS MINER TRAILING CABLE FROM THE ROOF WHEN THE EMPLOYEE REPORTED PAIN IN HIS LOWER BACK HEIGHT 64IN 2/0 TRAILING CABLE-WATER LINE NOT ATTACHED THIS INCIDENT SHOULD BE CLASSIFIED AS ADEGREE 3 (CASE INVOLVING DAYS AWAY FROM WORK) & CLASSIFICATION 09 (HANDLING MATERIAL) EVENT

EMPLOYEE AND A CO-WORKER WERE INSTALLING A 48" BOTTOM BELT ROLLER ON AN IDLE CONVEYOR. WHILE PERFORMING THIS TASK THE EMPLOYEE REPORTED EXPERIENCING A PAIN IN HIS LOWER BACK.

EMPLOYEE & CO-WORKER WEREE REPLACING A PANEL COVER (APPROX 150#) ON A JOY 10SC SHUTTLE CAR. CO-WORKER INADVERTENTLY DROPPED 1 END & CAUSED ADDITIONAL WEIGHT TO BE TRANSFERRED TO THE EMPLOYEE'S END CAUSING A PAIN IN HIS LOWER BACK. THE SHUTTLE CAR WAS IDLE-MAINTENANCE BEING PERFORMED-AT TIME OF ACCIDENT. THIS EVENT SHOULD BE CLASSIFIED AS DEGREE 3, CLASSIFICATION 09-HANDLING MATERIA

EMPLOYEE STATED HE DROPPED A BUNDLE OF TEN 6" ROOF BOLT PLATES AND THAT STRUCK HIM ON THE CALF OF HIS RIGHT LEG. NO VISIBLE INJURY WAS DETECTED. EMPLOYEE STATED HE WAS LOADING SUPPLIES ONTO TH T TOP OF A ROOF BOLTING MACHINE WHEN THE ALLEGED ACCIDENT OCCURRED. THIS EVENT SHOULD BE CLASSIFIED A DEGREE 3, CLASSIFICATION 09-HANDLING MATERIAL ACCIDENT.

EMPLOYEE AND FOUR CO WORKERS WERE LOADING 60 LB RAILS FROM MINE FLOOR ONTO A FLAT CAR. AS THEY PLACED ONE RAIL ON THE FLAT CAR, THE RAIL TURNEDOVER AND CAUGHT THE EMPLOYEES MIDDLE AND RING FINGERS RESULTING IN A LACERATION. ACCIDENT SHOULD BE CLASSIFIED AS A DEGREE 3 CLASS 9 HANDLING MATERIAL. SUTURES WERE REQUIRED TO CLOSE FINGER WOUNDS.

EMPLOYEE AND TWO CO WORKERS WERE PULLING THE TRAILING CABLE OFF THE CABLE REEL OF A FLETCHER DD0-15CD ROOF BOLTING MACHINE. THE CABLE HAD BECOME FOULED IN THE REEL. WHILE PULLING /TUGGIN G ON THE TRAILING CABLE. THE EMPLOYEE REPORTED EXPERIENCING PAIN IN HIS LOWER BACK. ACCIDENT SHOULD BE CLASSIFIED AS FOLLOWS: DEGREE 3, CLASSIFICATION 09-HANDLING MATERIAL. ROOF BOLTER

IMPROPER LIFTING OF MATERIALS.

EE WAS HANGING THE TRAILING CABLE AND THE WATER LINE FOR A CONTINUOUS MINER AGAINST THE MINE ROOF WHEN HE REPORTED A SHARP PAIN IN HIS LOWER BACK. HE WAS UNABLE TO RETURN TO WORK ON HIS NEXT R EGULARLY SCHEDULED SHIFT.

EMPLOYEE BENT OVER TO PICK UPA HYDRAULIC JACK WHEN HE EXPERIENCED A SUDDEN PAIN IN HI LOWER BACK. THE HYDRAULIC CYLINDER WAS APPROX 6' IN DIAMETER BY 3' IN LENGTH AND WAS LAYIN GON THE MINE LFOOR. THIS ACCIDENT SHOULD BE CLASSIFIED AS A DEGREE 3, ACCIDNET CLASSIFICATION 09. HANDLING MATERIAL. THIS EMPLOYEE HAS A HISTORY OF BACK PROBLEMS.

EMPLOYEE AND TWO CO-WORKERS WERE LOADING 60 LB. RAILS FROM THE MINE FLOOR ONTO A FLAT CAR. THE EMPLOYEE EXPERIENCED A SUDDEN SHARP PAIN IN HIS LOWER BACK. HE CONTINUED TO WORK FOR SEVERAL MINU TES BUT WAS FORCED TO STOP BECAUSE OF THE INCREASING PAIN. HE DID NOT WORK ON HIS NEXT SCHEDULED SHIFT (MAY 9, 1994). THIS ACCIDENT IS A DEGREE 3, CLASSIFICATION 09 (HANDLING MATERIAL) ACCIDE

EMPLOYEE WAS ATTEMPTING TO MOVE A PIECE OF ROCK BY HAND WHEN HE EXPERIENCED A PAIN IN HIS LOWER BACK. THE ROCK THE EMPLOYEE WAS ATTEMPTING TO MOVE WAS APPROX 34' L X 16' W X 1/2" TO 2" THICK. THIS ACCIDENT SHOULD BE CLASSIFIED AS A MATERIAL HANDLING EVENT. THE ACCIDENT OCCURRED IN THE #4 ENTRY NEAR STATION SPAD #9706. EMPLOYEE BEGAN MISSING WORK ON HIS NEXT SHIFT.

EMPLOYEE WAS CARRYING A 5 GALLON BUCKET OF GREASE IN BELT ENTRY NEAR #9 BELT HEAD. HE BUMPED HIS HEAD AGAINST THE MINE ROOF & REPORTED AN INJURY TO HIS NECK. EMPLOYEE COMPLETED HIS REGULAR S HIFT & WORKED ON NEXT SCHEDULED SHIFT. HE BEGAN MISSING WORK ON 2/5/94. THIS ACCIDENT SHOULD BE CLASSIFIED AS A DEGREE 3 ACCIDENT CLASSIFICATION 20. (STRIKING OR BUMPING).

LIFTING A CARRYING GEAR REDUCER APPROX. 75 YDS. TO THE THICKENER AT THE PREP PLANT. SEVERE PAIN IN LOWER BACK.

INDIVIDUAL HAD CUT LEFT HAND BREAK, HE WAS POSITIONING CONTINUOUS MINER TO SQUARE BLOCK ON LEFT SUMP. HE WAS IN THE PROCESS OF PULLING THE CONTINUOUS MINER CABLE AND WATER LINE OUT OF THE ROA DWAY. WHILE PULLING THE CABLE AND WATER LINE HEFELT A PAIN IN HIS LOWER BACK.

INDIVIDUAL WAS LIFTING A BOX OF RESIN GLUE AND FELT SOMETHING PULL IN HIS SHOULDER.

EMPLOYEE WAS ATTEMPTING TO LIFT A HYDRALIC CYLINDER WHEN HE EXPERIENCED A SUDDEN PAIN IN HIS LOWER BACK. HE MISSED WORK ON 7-16-93 AND REMAINED OFF UNTIL HE RETURNED ON 8-2-93(15DAYS OFF). HE WORKED FROM 8-2-93 UNTIL 8-10-93 FIRST DAY OFF ON RECURRENCE. HE REMAINS OFF WORK. THE OVERSIGHT IN REPORTING THIS OCCURRENCE WAS DISCOVERED DURING AN INTERNAL RECONCILATION OF ACCIDENTS.

LIFTING ON 4"X8" HEADER TO LOAD INTO SCOOP BUCKET TO BUILD OVERCAST AND STRAINED HIS LOWER BACK.

INDIVIDUAL WAS BOLTING TOP AND WENT TOT HE REAR OF THE ROOF BOLTING MACHINE TO GET SOME RESIN GLUE. HE CARRIED EIGHT STICKS OF RESIN GLUE TO THE FRONT OF THE MACHINE. HE THEN PROCEEDED TO IN STALL TWO RESIN BOLTS. AFTER DOING THIS, HE COMPLAINED OF PAIN IN HIS LOWER BACK.

INDIVIDUAL WAS HELPING LOAD 42" BELT ONTO FLAT CAR. THE INDIVIDUAL WAS ON TOP OF THE BELT HOLDING IT DOWN. THE BELT CAME TO THE END OF THE OF THE ROLL, IT BECAME FOULDED PULLING THE BELT OF TH E FLAT CAR. AS THE BELT CAME OF THE FLAT CAR, THE INDIVIDUAL FELL TO THE GROUND.

INDIVIDUAL WAS ATTEMPTING TO MOVE THE BELT ROLLER AROUND SO THE END OF THE SHAFT WOULD BE POSITIONED TO PLACE THE BEARING ON IT. AFTER PULLING ON IT, THE PERSON COMPLAINED OF PAIN IN HIS BACK AND LOWER STOMACH.

INDIVIDUAL WAS HELPING ELECTRICIAN LIFT DRILL POT FROM A 3-WHEELER OVER TO THE DRILL BOOM OF THE FLETCHER ROOF BOLTER, WHILE LIFTING THE DRILL POT HE EXPERIENCED PAIN IN HIS LOWER BACK AND ADO MEN. THE INDIVIDUAL DID NOT START MISSING WORK DUE TO THE INJURY UNTIL 3/18/93.

INDIVIDUAL WAS IN MAN BUS LIFTING ONE END OF SCOOP CHARGER AND ANOTHER PERSON WAS PULLING ON ONE END OF THE CHARGER. HEAVY END CAME OUT OF MAN BUS (LIGHT END OF CHARGER TIPPED UP) AND JERKED T HE PERSON TO ONE SIDE. (ACCIDENT OCCURRED IN TRACK ENTRY)

INDIVIDUAL WAS LOADING ROCK DUST INTO ROCK DUSTER, HER PICKED THE ROCK DUST BAG OFF THE GROUND AND TURNED TO PUT IT ON TOP OF THE TRACK DUSTER, HE FINISHED ROCK DUSTING AND STARTED HIS REGULAR SHIP AS SHUTTLE CAR OPERATOR. HE WORKED UNTIL 6:16 WHEN HE WAS TRANSPORTED OUTSIDE BY THE BELT EXAMINER.

INDIVIDUAL WAS UNLOADING BELT BOX FROM ROLL BACK TRUCK AND HIS CHAIN FOULED UNDER THE POWER BOX, HE STEPPED DOWN FROM THE FORK LIFT AND TRIED TO PULL THE CHAIN STRAINING HIS BACK.

INDIVIDUAL STOPPED MAN BUS (SURFACE) AT SUPPLY YARD. INDIVIDUAL GOT OUT OF MAN BUS TO LOAD FLY PADS (ABOUT 75-80 LBS). INDIVIDUAL STRAINED HIS BACK. (TOSSED ROLL OF FLY PADS ON MAN BUS)

HAD ROCK IN HIS HAND TOSSED THE ROCK THRU LINE CURTAIN HIT HIS HAND AGAINST RIB REQUIRING SEVEN STITCHES.