Buscar en el registro

Employee was welding, cutting, and grinding plate metal and got a small metal flake in his eye. Employee reported that his eye felt irritated, so it was washed with an eye rinse solution. Employee was then sent to the doctor, and the metal flake was removed. Employee is expected to make a full recovery.

EMPLOYEE WAS CUTTING METAL WITH TORCH, WHEN SOME MOLTEN METAL WENT INSIDE HIS GLOVES, BURNING WRIST AND ARM.

Common procedure of installing PVC slip-joint pipe was being done when excavator was being used to push a 4x4 block against the pipe to put together. The 4x4 block broke and was propelled through the air and struck employee in the leg.

EMP WAS USING A BENCH GRINDER TO SMOOTH THE EDGE OF A FLAT BAR WHEN BAR KICKED UPWARDS PULLING HIS RIGHT THUMB INTO THE GRINDING WHEEL RESULTING IN HIS THUMB NAIL BEING 2/3 SNATCHED OFF ALONG WITH FLESH.

Another employee was cutting rebar on cutoff saw when a piece of rebar flew off striking injured employee on right arm causing laceration requiring stitches.

Employee and co-worker were removing motor from shelf with a hoist. Injured employee was holding motor guiding it down to level when co-worker pushed wrong switch causing motor to drop on injured employee's left little finger crushing it.

EMPLOYEE WELDING AND FOREIGN MATERIAL BLEW INTO LEFT EYE.

Employee was trouble shooting problem with low water pressure when high pressure hose knocked him down causing his hard hat to come off. He hit his head on concrete floor resulting in concussion.

While operating excavator, operator suddenly complained with back pain. After examination, Dr. prescribed rest for back strain.

Employee was cutting wood on a table saw when the wood kicked back cutting right hand requiring stitches.

MAKING WELDING REPAIRS ON A PUGMILL LID & HOT SLAG POPPED IN RIGHT EYE.

WHILE GRINDING ON BAG PACKER SOMETHING FELL IN EYE BEHIND FACE SHIELD. ANOTHER EMP WAS GRINDING IN THE SAME AREA.

EMPLOYEE WAS WELDING AND GRINDING IN THE SHOP. HE NOTICED HIS RIGHT EYE GETTING IRRITATED. HE WASHED IT SEVERAL TIMES AND TOOK SOME SOLUTION HOME TO WASH OUT ALSO. HE WAS WEARING SAFETY GLA SSES AND A FACE SHIELD. HE WENT TO DOCTOR THE NEXT DAY.

EMPLOYEE WAS THREADING CONDUIT IN RIGID 300 THREADING MACHINE. HAD THREADED CONDUIT, WENT TO REMOVE BUT DID NOT WAIT FOR MACHINE TO STOP. PIPE HUNG IN JAWS OF MACHINE, CAUSING PIPE TO CATCH HIS RIGHT HAND BETWEEN MACHINE AND CONDUIT MASHING 4TH FINGER.

EE WAS RIDING IN GOLF CART IN EARLY MORNING AND DID NOT SEE ROPE BARRIER. GOLF CART WENT THROUGHAND UNDER ROPE BARRIER CAUSING IT TO CUT AND BRUISE LEFT EYE AND CHEEK REQUIRING 6 STITCHES.

CUTTING STEEL PLATES WITH TORCH WEARING GOGGLES WHEN FIRE (METAL) GOT IN EYE CAUSING IRRITATION.

EE ALONG WITH OTHER CO-WORKERS WERE CHANGING A SHAFT IN A BLUNGER. THEY HAD TO USE A HYDROLIFT TO LIFT SHAFT THEN TRANSFER IT TO A CHAIN HOIST. THE SHAFT SLIPPED THROUGH THE HOIST AND THE BLAD E OF THE SHAFT HIT EE'S RIGHT LEG CUTTING IT REQUIRING FIVE STITCHES.

EE WAS INSTALLING SUPPORT BRACKETS TO HOLD WATER LINE. HE WAS USING GRINDER AND GRINDING OVERHEAD AND PARTICLE OF METAL GOT IN LEFT EYE. HE WAS WEARING SAFETY GLASSES WITH SIDESHIELDS.

REMOVING MOTORMOUNT OFF ENGINE OF BACKHOE #75. AIR WRENCH DIDN'T TURN OFF; BOLT CAME OUT CAUSING MOTORMOUNT TO SLASH RIGHT INDEX FINGER. SUTURES REQUIRED.