Buscar en el registro

Employee was cutting out a wear plate with a torch when hot metal dropped onto boot. The employee did not notice until it burned through boot

Miner was using a four inch grinder with a cutting wheel while cutting plate steel. Blade hung up in seam and shattered cutting miners left index finger. Miner received +/- 15 stitches in finger and was released back to duty.

Miner was preparing to cut the inner race of a bearing off of an overflow catch pan on a rip-rap machine, when pressure inside of catch pan forced adjacent bearing off of catch pan housing striking miner in left side causing contusion. Miner was taken to medical facility for observation.

Miner was burning holes under crusher for wear plate installation, when a piece of slag entered his right ear, causing a minor burn. This resulted in a trip to Urgent Care, at which point prescription antibiotics were prescibed.

Miner was cleaning stone from grizzlies when a stone slid from top of grizzlies smashing right ring finger between two pieces of stone.

Two employees were welding in close quarters and one employee suffered from flash burns to his eyes

EE WAS USING 3/8" DRIVE IMPACT TO REMOVE BOLTS FROM GAS TANKS STRAPS FOR REMOVAL OF TANK. BOLT HE WAS LOOSENING WITH IMPACT WAS SLIPPING. HE THEN NEEDED A WRENCH TO HOLD THE BACK SIDE. HE PLACED OTHER HAND ON BACK SIDE OF BOLT TO FEEL WHAT SIZE NUT IT WAS. AS HE PLACED HIS FINGERS ON THE NUT HE ACCIDENTALLY TURNED ON THE AIR GUN SPINNING NUT CUTTING FINGER.

INSTALLING STEP BRACKET ON REAR OF 980 F CAT LOADER. BRACKET HAD THREADED HOLES, PUT BOLT IN BRACKET AND TIGHTENED WITH AIR WRENCH, THE BRACKET ROTATED AROUND AND STRUCK EE ON LEFT THUMB.

GRINDING ON A STEEL PLATE WITH HAND GRINDER, WHEN GRINDER GOT CAUGHT. CAUSING IT TO FLIP BACK ACROSS THE TOP OF LEFT HAND.

EE WAS WALKING THRU SHOP AREA WHERE ANOTHER EE WAS GRINDING ABOUT 6' AWAY. AS HE WALKED BY DUST, DIRT OR STEEL GRINDINGS FLEW OFF INTO THE EE'S LEFT EYE.

ROLLED D-7 DOZER UP ON ITS SIDE DUE TO FROZEN SLOPE ICE CONDITIONS

HE WAS OPERATING PLASTIC STRETCH WRAP MACHINE. WHILE MACHINE WAS TURNING, HE REACHED IN TO ADJUST PLASTIC WRAP. THE PLASTIC CAUGHT ON HIS LEFT THUMB AND PULLED THE THUMBNAIL LOOSE.

EE STATED THAT HE WAS STRUCK BY GRINDER WHEEL WHEN GRINDER KICKED BACK AT HIM. EE WAS GRINDING WELDING SLAG OFF METAL.

EE WAS IN THE PROCESS OF VULCANIZING BELTS TOGEHTER ON CONVEYOR. HE USED AN AIR COMPRESSOR TO FILL AN AIR BLATTER TO APPLY PRESSURE ON BELTS. BOLT HOLDING METAL BEAM WAS NOT PROPERLY THREADED. PRESSURE BROKE BOLT THREAD ALLOWING BEAM TO FLYUP AND HIT HIS HEAD.

EE WAS USING DRILL TO DRILL HOLE IN METAL ANOTHER EE USED CUTTING TORCH TO HEAD METAL A PIECE OF SLAG WENT INTO EE EYE.

EMPLOYEE WAS CUTTING SOME CONVEYOR FRAME TO BE RE-USED WHEN THE PIECE HE WAS CUTTING FELL LOOSE & STRUCK HIM BEHIND THE STEEL TOE OF HIS BOOT. THE INJURY WAS A HAIR LINE FRACTURE TO HIS LEFT F OOT BEHIND THE TOE AREA.

EMPLOYEE WAS RUNNING A ST. REGIS BAG PACKER PACKING 50# BAGS WITH LIMESTONE. THE AUTO-SPRING LEVER TRIPPED STRICKING THE EMPLOYEE ON THE MIDDLE FINGER, RIGHT HAND.

EMPLOYEE WAS WORKING INSIDE THE CRUSHING CAVITY OF A 30 INCH CONE CRUSHER USING AN AIR ARC TO TRIM THE LOWER BELL ON THE CONE. DURING THE TRIMMING HE RECEIVED FLASH BURNS TO BOTH EYES.

EMPL WELDING IN PRIMARY CRUSHER HOPPER WHILE ANOTHER EMPL WAS USING ELECTRIC GRINDER.PIECE OF STEEL FROM GRINDER WENT BEHIND WELDING HOOD AND GOT INTO EMPL RIGHT EYE.