Buscar en el registro

Loading boulders into employees truck, rocking the truck and hurting their back, mid back pain.

Removing a bolt with air gun, bolt spun in the other hand causing the injury.

While using a die grinder, the grinding disk broke shooting a piece of the grinding disk into the employees arm.

Miner dropped an electric drill on his hand Thursday 5/24/2012. Results of his injury was a break to his hand. He did not tell his supervisor or seek treatment until he returned to work on 5/25/2012. Office was notified on 5/29/2012 that he will be off work until the hand is healed.

While working on hammermill, got cut on right hand. No accident report was filed. When injury healed, he realized there was metal stuck in his hand. He had surgery to remove it on 6/25/08 and was off work until 6/30/08. Missed 3 days of work.

Employee was helping to install a culvert at a crossing. He was adjusting chain and backhoe operator moved the bucket. Hand caught.

EMPLOYEE WAS REMOVING A BOLT FROM THE HEADRACK OF A HAUL TRUCK WITH AN IMPACT WRENCH. THE WRENCH SLIPPED & THE EE CAUGHT HIS RING ON METAL RACK, CUTTING HIS FINGER, REQUIRING (2) STITCHES.

While using a power washer to clean an oil cooler, employee slipped and the washing nozzle came in contact with the top of his left foot causing a burn & torn skin.

Employee developed a pain in the lower back after operating a Caterpillar D8 bulldozer.

EE WAS WORKING FROM WALKWAY AROUND BREAKER FEEDER USING A BAR TO DISLODGE ROCKS. A PIECE OF ROCK SHOT OUT OF BREAKER STRIKING EE ABOVE THE LEFT EYE. ROCK SHOT OUT THROUGH THE PROTECTIVE CHAINS . EE WAS WEARING SAFETY GLASSES.

EMPLOYEE WAS USING AN AIR CHISEL TO REMOVE BOLTS AND A PIECE OF SLAG BOUNCED BACK AND HIT HIM IN THE LEFT CHEEK. EMPLOYEE WAS WEARING PROPER EYEPROTECTION.

WHILE MOVING DRILL AND COMPRESSOR FROM THE BENCHEMPLOYEE RAN OVER A ROCK AND JOLTED HIS BACK RESULTING IN A PULLED MUSCLE AND LOWER BACK STRAIN.

EMPLOYEE WAS INSTALLING THE BELLY PAN ON THE CAT 325 EXCAVATOR UNIT 968 WHEN A BOLT HE WAS TIGHTENING BROKE AND THE AIR WRENCH FELL SMASHING HIS RIGHT HAND, NO BROKEN BONES. DR PACKED IT WITH ICE AND PRESCRIBED MEDICATION.

CRUSHING CREW WAS CLEANING THE HAMMER MILL THAT HAD PLUGGED ITSELF WITH ROCK AFTER THE HAMMER MILL DISCHARGE MOTOR HAD QUITR WORKING. AFTER SOME CLEANING ANOTHER EE TOLD EVERY ONE TO STAND CLE AR SO THAT HE COULD START THE DIESEL DRIVE OF THE MILL & REPOSITION HAMMERS FOR FURTHER CLEANING. EE REACHED IN MILL TO GRAB A LARGER ROCK & DISCARD IT. HAMMER FELL PINCH FOREARM, TORN ARTERY

EE WAS WORKING ON A IMPACT IN THE BAR AREA AND WHILE WELDING HE BUMPED HIS RIGHT ELBOW. THE ELBOW BECAME SWOLLEN AND INFLAMED.

EE WAS WORKING CLEANING UP PARTS ON BENCH GRINDER. HE WAS WEARING HIS SAFETY GLASSES. SOMEHOW A SMA;; PIECE OF WIRE MUST HAVE CAME OFF AND GOT BEHIND HIS GLASSES. THIS SMAL PIECE EVENTUALLY WA S FOUND FLOATING AROUND IN HIS EYE. IT WAS REMOVED BY A DR. EE WAS GIVEN EYE DROPS FOR THE DISCOMFORT. EE DID NOT MISS ANY TIME OFF.

EE WAS REPLACING END CAPS IN TROUGHING ROLLERS. HE WAS USING A SMALL CUTTING TORCH TO HEAT UP END CAPS AND ALSO HAD A 8" PRY BAR TO POP CAPS OUT AS HE HEATED END CAP WITH ONE HAND THE WOULD TH EN USE THE PRY BAR IN HIS RIGHT HAND TO POP IT OPPED OUT AND WENT IT DID THE TORCH IN HIS OTHER HAND CAME ACROSS THE BACK OF HIS RIGHT HAND. BURNING HIM.

EE WAS WORKING ON A CAT A-FRAME. HE NEEDED TO ROLL FRAME OVER SO HE HOOKED A-FRAME TO A CHAIN HOIST & PROCEEDED TO LIFT & ROLL FRAME OVER. AS HE SET FRAME DOWN ON THE FLOOR, HIS ONE FOOT WAS I N A POSITION THAT IF THE FRAME ROLLED BACK IT WOULD PIN HIS FOOT. THIS IS WHAT HAPPENED WHEN THE CHAIN WAS LOOSENED. A-FRAME WAS NOT SET & BLOCKED PROPERLLY. EE BRUISED TOP OF LEFT FOOT.

EMPLOYEE WAS BULDING UP THE WORN IMPELLER BARS IN THE CEDAR RAPIDS IMPACT BREAKER. HE WAS WELDING WITH HELMET DOWN & RAISING IT UP TO CHECK WORK. THIS WAS IN TOTAL DISREGARD TO HIS OWN SAFETY. REFLECTION OF THE ARCH IS WHAT DIRECTLY CAUSED THE SLIGHT BURN TO HIS FACE. HELMET WAS IN GOOD CONDITION.EMPLOYEE RECEIVED A FULL RELEASE TO RETURN TO WORK.

EE WAS REBUILDING A LIME GRATE THAT SEPARTES FROZEN CHUCKS OF LIME FROM FINE MATERIAL.AS EE WAS GRINDING SMALL PARTICLES WENT UP AROUND HIS SAFETY GLASSES. IT WAS NOTED THAT HE WEAR A CLEA R FACE SHIELD OVER SAFETY GLASSES. TIGHTER FITTING SAFETY GLASSES WILL BE PURCHASED TO STOP ANY AND ALLPARTICLES.

EMP WAS HELPING MECHANIC REPAIR STINGER THAT FITS ON CAT. EMP WAS USING GRINDER ON STINGER IN PREPARATION FOR SOME WELDING. AS EMP WAS GRINDING, GRINDER SLIPPED OUT OF HAND AND STRUCK HIM ON L EG. GRINDER IS LARGE AND POWERFUL. IT WAS DISCOVERED THAT BETWEEN THE WIEHGT, THRUST AND LOOSE GRIP OF GRINDER, THAT THIS ACCIDENT WAS BOUND TO HAPPEN. EMP SUFFERED LACERATION APPROX 2" LONG.

EMP WAS DRILLING HOLES IN ROCK LEDGE AND WAS PREPARING TO MOVE DRILL TO NEXT LOCATION. AS EMP MOVED DRILL STEP ON WHICH HE WAS STANDING RAN OVER 8" ROCK CAUSING STEP TO BE THRUST UPWARD AND TH EN CAME DOWN SHARPLY. AS EMP CAME DOWN KNEE WAS SOMEWHAT TWISTED. THIS CAUSED A SPRAIN TO RIGHT KNEE. LEDGE WILL BE FREE OF ANY LOOSE OR FOREIGN MATERIAL BEFORE DRILLING.

EE AND A FELLOW EE WERE ADJUSTING DRIVE BELTS ON THE BREAKER BELT. EE WAS USING A TORCH TO HEAT UP THE ADJUSTER BOLTS. AFTER HEATING THE ADJUSTER BOLTS, THE TORCH WAS LAID ON THE BELT STILL LI T. EE STEPPED BACK CLOSE TO THE TORCH AND BURNEDHIS LEFT FOOT. HE HAS BEEN INSTRUCTED NOT TO SET TORCH DOWN WHILE LIT.

OPER CAT AND PULL SCRAPER PC OF STEEL CAME OFF CABLE HITTING IN EYE

THE INJURED PERSON WAS STARTING A WATER PUMP WHEN THE DISCHARGBE HOSE RELEASED FROM THE PUMP. THE FORCE OF THE WATER CAUSED HIM TO FALL TO THE GROUND LANDING ON HIS RIGHT ARM.