Buscar en el registro

Tire service tech, operating a IMT tire service crane/manipulator. Pick up a 3300-51 haul tire in a scrap pile. Lifted tire approximately 6'ft, tire slipped out of tire clamp, impacting the ground and rolled onto service tech operating controls. Pinned by weight of tire, causing several broken bones. Wet weather..

Employees were replacing teeter tubes inside the hydrosizer. There were filings left inside tubes from drilling out nozzles. While lowering teeter tubes filings fell onto employee getting into left eye. Employee flushed eye and thought debris was cleaned out. On 5/31/18 employee was taken to the doctor and a small fragment of metal was removed.

Employee reported to work on 6/23/16, knee was swollen so employee left to see doctor. Employee was admitted into the hospital with a staph infection. Employee had some old welding burns on arm and possibly one on leg. It's unclear as to what caused the infection and waiting for doctors report.

Employee was Using an air arc, had face shield and safety glasses on. Employee lifted shield, had not pushed the air release button on gouging torch which blew debris into the air. Employee did not feel anything in the eye until that night and did not seek medical attention or report until the next day. The eye doctor removed a small particle of rust from the eye.

Employee was using a saws-all to cut a 2x6 stud with a plywood sheet attached to the back. The saw kicked back when it hit a knot or a screw in the wood, cutting left 5th digit and requiring stitches.

Employee was using a drill press to drill 1-1/2 inch hole, bit was slipping so employee was using a chuck to tighten. Employee stepped to the right to get a better position and hit the foot actuator, turning the drill bit and chuck. Employee had two stitches in hand as a result.

Employee was using a pressurized grease system on 2085 lube truck to get a small amount of grease to put on the o-ring on a hyd. filter while servicing a D10 dozer. The grease system injected grease through the gloves and into the right hand, 3rd joint of middle finger.

Employee became entangled in the rotating drill steel on the air track drill when he left the cab for some unknown reason.

Mechanic was using a wire feed welder when he missed and the wire went through the seam of his welding glove and hit his finger. The finger later became infected and the individual had to have his finger lanced and be treated with IV antibiotics on 12/26/2006.

Employee claimed he was driving motor grader and hit a rock. He did not report accident until next day after he went and saw a chiropractor for neck and shoulder discomfort. A Workers Compensation claim was made 8/7/07.

Employee was being loaded by an excavator when a large rock rolled in the bed striking the side of the truck bed. Employee was bounced around in the cab causing possible whiplash.

Employee was sitting in cab of haul truck being loaded by excavator when a large rock rolled off the bucket, hitting headache rack on the truck. Jarred their back.

EE was prepairing metal for welding. The grinding wheel caught on the edge and sprayed paricles in the left eye. The EE was wearing a facesheild and safety glasses.

Employee removed the top cover on the radiator housing to see why the cap was leaking. When the Employee reached to remove the cap it blew off spraying the employee with hot antifreeze.

EE was operating a dozer in rough terrain all day, causing stiffness in lower neck and upper back.

Employee was removing snow from the mine haul road with a motor grader and hit a rock jarring lower back.

Removing rocks with a Jack Hammer on mine access road. Strained back when moving Jack Hammer.

EE HIT A LARGE ROCK BURIED IN MUD WHILE BLADING HAUL ROAD. WHEN HE HIT THE ROCK, HE SUFFERED AN INJURY TO THE LOWER BACK.

AIR COMPRESSOR WAS BEING CHECKED FOR FUEL LEAKS.EE HAD LEFT HAND ON ENGINE FRAME WHILE CLIMBING.HE SLIPPED & LEFT HAND WENT INTO FAN CUTTING RING FINGER. SURGERY REQUIRED TO REPAIR TENDON.

AFTER WELDING ON A PIECE OF EQUIPMENT, INDIVBIDUAL WENT TO HAVE LUNCH AND NOTICED SOMETHING IN EYE. A FOREIGN OBJECT WAS REMOVED FROM EE'S RIGHT EYE AT HOSPITAL.

EMPLOYEE WAS REPLACING A DOOR ON 21210. IT REQUIRED GRINDING A RIVET OFF. A LIVER OF ALUMINUM BECAME EMBEDDED IN HIS RIGHT EYE.

GRINDING A WELD - RESULTED IN FOREIGN OBJECT IN RIGHT EYE.

REMOVING BALLMILL LIFTERS WITH A 1" IMPACT WRENCH

EE WAS BEING LOADED BY 11260 SHOVEL, A ROCK FELL OUT OF SHOVEL BUCKET & HIT ON THE BACK OF TRUCK BED, CAUSING TRUCK TO BOUNCE & JAR THE DRIVER.

EE WAS OPERATING #15830 WHEEL DOZER WITH THE DOOR OPEN. HE HAD HIS HAND ON THE DOOR JAM, THE DOOR SWUNG SHUT AND SMASHED HIS LEFT THUMB.

RUNNING MANLIFT FOR ANOTHER EMPLOYEE WHO WAS WELDING ON AN OVERHEAD. WELDING FLASH BURN TO THE EYES.

SLAG IN RIGHT EYE. EE WAS WELDING ON A TRUCK IN A CONFINED SPACE.

CUTTING MAIN SUPPORT BOLT ON SPOOL OF NEW TAILS THICKNER - FELL AND TRAPPED ARMS BETWEEN FLANGES - CRUSHED BOTH ARMS

WELDONG ON BUCKET WITH 3 OTHER GUYS RECEIVING FLASH BURNS TO EYES.

CUTTING FINGER WHITH PORTA POWER SAW.

CLEANING UP IN WAREHOUSE, LIFTING A BEARNING ASSEMBLY WITH THE OVERHEAD CRANE. BEARNING ASSEMBLY SLIPPED AND PINCHED RIGHT HAND BETWEEN ASSEMBLY AND MOTOR RESULTING IN A SMASH RIGHT RING FINGE R.

WORKING WITH GRINDER

CLEANING HOT ORE OUT OF TOWER, HOT ORE BROKE LOOSE AND SLID DOWN CHUTE, CAUSING FIRST AND SECOND DEGREE BURNS TO BOTH LEGS FROM THE KNEE TO FOOT.

WORKING ON ED-33 THE SOCKET ON THE AIR IMPACT WRENCH CAME OFF AND HIT LEFT FRONT TEETH.

SEAT KEEPS BOTTEMING OUT LOWER & UPPER BACK.

JARRING OF SHOVEL RESULTED IN SPRAINED BACK

THE ROTATING SHAFT END HAD BEEN MODIFIED TO ALLOW FOR MANUAL ROTATION. THIS HAD BEEN DONE BY WELDING A BOLT TO THE END. THIS BOLT HAD EDGES FROM PIPE WRENCHES THAT SNAGGED A CLOTH GLOVE THEREF ORE PRECIPITATING THE ACCIDENT. DAMAGE WAS TO THE LEFT HAND INDEX AND MIDDLE FINGERS, LACERATIONS TO MIDDLE. AT TIME OF WRITING, NOT KNOWN IF INDEX WILL BE AMPUTATED.

IN THE NORMAL OPERATION OF PUSHING UP TO A LOADER, THE SEAT THE OPERATOR WAS SITTING ON BROKE LOOSE AND THE OPERATOR WENT FORWARD HITTING THE DASH.

OPERATING A HYDRAULIC SHOVEL IN NORMAL MANNER AND COMPLAINED OF PAIN IN LOWER BACK.

USING GRINDER PARTICLE WENT BEHIND GLASSES INTO RIGHT EYE

NORMAL CONDITIONS,OPERATING A DOZER.

ANOTHER EMPLOYEE WAS USING A METAL GRINDER WHEN SPARKS FROM THE GRINDER ENTERED HIS EYE THROUGH THE SIDE OF HIS SAFETY GLASSES

CUTTING PIPE 6 3N PIECE CUT OFF FELL ROLLED INTO LEG

GRINDING ON DIS5 CUTTER TABLE-PIECE OF COLD ROLL STOCK FELL OFF TABLE-HIT FOOT ABOVE SAFETY TOE ON BOOT.

OPERATOR WENT O0F SITE TO PULL STUCK TRUCK/TRAILER (SEMI) UP TO MINE SITE WHILE HOOKING UP RUBBER TIRE DOZER ROLLED BACKWARDS PINNING OPERATOR BETWEEN MACHINE AND TRUCK

OPERATIRN A SCR5PER CROSSED A SNOW FILLED DITCH HARD BUMP STRUCK MOUTH ON STEERING WHEEL

CUTTING A PLATE OFF SHOVEL BUCKET & OTHER SIDE DIDN\T HOLD AFTER CUTTING HIS END. PLATE CAME DOWN & HIT HIM INSIDE OF LEFT KNEE STITCHES & BRUISED UP.

BUFFING WITH GRINDER WIRE WHEEL CAUGHT GRINDER SPUN DOWN AND TWISTED R/WRIST

EMPLOYEE WAS SETTING CAB WITH A HOIST HE PUSHED BUTTON TOO HARD CAB DROPPED HAND WAS IN BETWEEN CONSOLE AND CAB - CAB CANOPY CRUSHED FINGERS ON LEFT HAND SECOND FINGER ON LEFT HAND WAS SEVERE D AT FIRST KNUCKLE