Buscar en el registro

While unclogging FD5 back mixer, operator was trying to move the stuck turbulizer to get it to rotate and continue cleaning. The turbulizer broke free and the paddle struck the operator's right palm resulting in a laceration that required medical attention. The operator needed 12 stitches.

Employee was using a grinder to prepare surface when a fragment of the wire wheel struck EE in EE's eye. Employee was wearing EE's PPE for the task which included Hard Hat, Safety Glasses, Face Shield and Gloves. Employee used the Emergency Eye Wash station on site and after the rinse EE still felt that there was more in the eye. Sent for medical evaluation

Drilling steel with a reamer. Reamer caught and spun the drill around.

Sparks from grinding activities above EE got into EE's eye. EE was wearing safety glasses.

An employee went to clear a bag that was stuck in-between the discharge conveyor belt and idle roller on Roto Packer C, while the equipment was energized and still moving, in clear violation of procedures . When EE tugged on the bag it dislodged and pulled EE's hand and arm into the pinch point. The employee received bruising to EE's hand and arm.

Employee welding pipe in an awkward position, causing the employee to get a strained neck.

While an employee was using a parts washer, the hose for the brush disconnected, spraying the cleaning solution onto the employees torso and face. Some of the solution went behind his safety glasses and into his right eye. The employee received eye irritation with no damage.

While using a right angle grinder on a flange that had been cut off. individual lost control of the grinder. Individual received a cut to his right forearm.

Employee cut back of left index finger with hand-held grinder.

Employee was working in the fab shop grinding. He slipped and the grinder hit his hand.

Employee was putting a filter back into service after filter sock change. The filter lid gasket leaked upon the introduction of slurry product. Hot slurry released onto the back of the employee's head/neck/behind ear area. 1st degree burn to approximately 6" x 6" area and 2nd degree burn to approximately 1" x 1" area.

Employee operating overhead hoist. The control pendant slipped from his grasp and struck his knee causing a contusion.

EE WAS HAND-SPOUTING EVERY OTHER SPOUT ON ROTO PACKER WITH PLASTIC BAGS. EE FOUND HIS ARM/SHOULDER TO BE SORE WHEN SHIFT WAS OVER.

APPLYING TENSION VIA HAND TO REEL OF PAPER BAGS, HAND GOT CAUGHT BRUISED, BUT NO BROKEN BONES.

GRINDING A NUT ON A BENCH GRINDER HE GOT METAL ABRASION IN RIGHT EYE.

HOLDING PUMP FOR TEST WHAN PUMP WAS TURNED ON. EVERYONG KNEW THE PUMP WAS TO BE TURNED ON. HOSE SLIPPED AND HIT EMPLOYEE IN THE HARD HAT. HE WAS KNOCKED TO THE FLOOR. HAD A LEFT SHOULDER ABRAS ION FROM THE HOSE.

EMPLOYEE WAS CUTTING STEEL AROUND THE AREA INJURED WAS WORKING IN. A PIECE OF STEEL FLEW IN THE AIR AND HIT INJURED IN THE BACK.

HE WAS REMOVING A SCREW FROM METAL STUDS AND APPLING PRESSURE TO THE RIGHT AND THE SCREW GUN SLID OVER ALLOWING HIS HAND TO HT A SHARP EDGE.

WHILE USING PORTABLE PIPE THREADER CENTRIFUGE BOWL ROLLED BACKWARD CRUSHING MIDDLE FINGER. OPERATOR WAS UNPLUGING CENTRIFUGE

GRINDER CAUGHT AND PUSHED LEFT HAND BETWEEN TWO RAILS.

HE WENT TO SHUT OFF BULK BAGGER AND HIS ARM GOT HOOKED ON I-BEAM DISLOCATING ELBOW.

HE WAS RUNNING A JACKHAMMER AND IT SLIPPED , SMASHING HIS HAND AGAINST A CONCRETE WALL. HE RECEIVED A FRACTURED LEFT RING FINGER AND 7 STITCHES TO REPAIR A LACERATION.

EE WAS USING CUTTING TORCH REMOVING STEEL. THE STEEL WAS ZINC COATED GALVANIZED. EE INHALED TO MANY FUMES AND HE BURNED HIS LUNGS SLIGHTLY.

HE WAS CUTTING HOLES IN EXISTING SIDING AND THE SAWZALL JUMPED BACK HITTING HIS FINGER.

HE WAS GRINDING METAL AND HE LIFTED HIS FACE SHIELD. A METAL SHAVING FELL FROM THE SHIELD BEHIND HIS GLASSES INTO HIS RIGHT EYE.

AIRHEATER JAMMED CLOGGING TURBOU 2ER/BADMIXER.EEWAS ATTEMPTING TO FREE BLADE & BLADE CAUGHT THUMB. LACERATION RIGHT THUMB REQUIRING 13 STITCHES

LOWERING A SPOOL FOR REPLACEMENT OF AN EMPTY WITH A CRANE, THE EE ATTEMPTED TO GUIDE IT AWAY FROM FENDING. SPOOL LOWERED ON EE'S FINGER BECAUSE THERE WAS NO ROPE TO STEADY LOAD.

EMPLOYEE HAD JUST COMPLETED A CUTTING OPERATION. THE TORCH, WHILE STILL LIT, SPUN IN EMPLOYEE'S HAND, BURNING HIS FACE AREA OF THE LEFT EYE, CHEEKBONE AND BROW.

EMPLOYEE WAS WELDING AND CHIPPING STEEL THROUGHOUT THE DAY. A PIECE OF STEEL APPARENTLY FELL FROM HIS HAIR OR CLOTHING INTO HIS EYE.

GRINDING 10" JOINT EMPLOYEE SET GRINDER ON LEG BEFORE IT HAD COMPELTELY STOPPED.

DRILLING HOLE IN BEAM, WHENCOMING DOWN LADDE RNOTICED IRRITATION IN LEFT EYE.

STEPPED IN DEPRESSION IN GROUND WHILE JACK HAMMERING AND STRAINED BACK.

EMPLOYEE WAS DRILLING HOLES IN A W36 BEAM WITH A 1/2" CAP PLATE. HE HAD DRILLED THROUGH 1/2" CAP PLATE, HE HAD STOPPED THE DRILL TO REMOVE THE 1/2" PLUG. WHEN HE CONTINUED DRILLING THROUGH THE BEAM, THE DRILL BIT CAUGHT AND BROKE THE MAGNIT FREE CAUSING THE HOUGEN DRILL TO STRIKE EMPLOYEE'S LEFT FOREARM.

EE WAS HANGING METAL STUD AND SHEETROCK WALLS. HE WAS APPLYING PRESSURE TO SCREW GUN WHILE SCREWING SHEET ROCK DOWN, STRAINING HIS RIGHT WRIST.

HE WAS JACKHAMMERING CONCRETE WALL WHERE THE FLOOR AND WALL COME TOGETHER. THE JACKHAMMER BROKE THROUGH ALL AT ONCE PULLING HIM AND JACKHAMMER INTO WALL.

EMPLOYEE WAS GRINDING THE INSIDE OF A METAL COLUMN ENCASEMENT. HE WAS WEARING A FULL FACE SHIELD. WHILE GRINDING A PIECE OF METAL FILING FLEW UP AND IMBEDDED IN HIS LEFT EYE.

EMPLOYEE WAS STANDING UNDERNEATH (10 TO 15 FEET)ANOTHER EMPLOYEE WHO WAS HANDLING THE SAWZALL. MATTER ENTERED LEFT EYE OF EMPLOYEE-THREE PIECES TAKEN OUT AT LOCAL HOSPITAL 2/3/93.

EMPLOYEE WAS REBUILDING GRINDING MILL (WELDING-CUTTING-GRINDING)EMPLOYEE DID NOT KNOW WHEN DEBRIS WENT INTO HIS EYE

DRILLING 3/4" HOLE IN STRUCTURAL STEEL. HE WAS IN A CONFINED AREA SO HE HAD HIS SIDE OF HEAD AND SHOULDER PRESSED AGAINST ABOVE DECKING AND WHEN HE WAS DIRLLING IT PUT PRESSURE ON HIS NECK PI NCHING A NERVE.

INJURED WAS GRINDING WELDS FROM A STEEL BEAM AND A CHIP OF METAL FLEW UNDER HIS SAFETY GLASSES AND EMBEDDED IN EYE.

EMP. WAS LEANING OVER ROOF & WATCHING WHILE CABLE WAS BEING LOWERED OVER SIDE OF BLDG. THE CABLE SLIPPED & WEDGED HIS THUMB BETWEEN ITS THE ROOF PARAPET.

EMP WAS WORKING NEXT TO A METAL GRINDING OPERATION DEBRIS SHOOTING OFF THE GRINDING WHEEL WENT PAST EMPS GLASSES & INTO HIS EYE BECAUSE OF HIS PROXIMITY TO THE GRINDING OP & HIS POSITION STANC E HE WAS SUSCEPTIBLE TO THE DEBRIS PARTICLES REACHING HIS LEFT EYE

EMP. WAS PAINTING OVERHEAD W/AIRLESS SPRAYER (INSIDE). THE OVERSPRAY SETTLED ON HIS FACE & SEEPED UP UNDER HIS SAFETY GLASSES & SETTLED ON HIS CHEEK BONES.

EMPL WAS OPERATING LIFT & LOOKING UP AT 2ND LEVEL OF DECKING FOR PROLONGED PERIOD. PAINTING OPERATION WAS GOING ON 3RD LEVEL OF DECKING & OVERSPRAY WAS ENTERING EMPLS WORK AREA. BECAUSE HE WAS LOOKING UP FOR SO LONG THERE WAS CONTINUED EXPOSURE TO SETTLING OVERSPRAY ON FACE.

GRINDING METAL INSIDE A BLDG HAD THROAT DISCOMFORT THAT AGGRA. BY THE GRINDING DUST.

EMPLLYEE WAS JACKHAMMERING CONCRETE FLOOR WHEN SECTION OF CONCRETE HE WAS STANDING ON GAVE WAY THE JACKHAMMER LURCHED FORWARD PULLING THE EMPLOYEE WITH IT HE EXPERIENCED PAIN IN HIS LOWER BACK BECAUSE OF THIS

EMPL REMOVING PAINT FROM A STEEL BEAM WITH GRINDER. GRINDER HAD WIRE BRUSH ATTACH. FOR PAINT REMOVAL BRUSH HIT 2 X4 DURING THIS ACTIVITY SPLINTED 2 X 4 DSUT AND SPLINTER WENT IN L EYE

EMPLOYEE WAS CHECKING FOR A KNOCKING SOUND IN COMPRESSOR. WENT TO REMOVE COVER., REMOVED 2 BOLTS AND COVER WOULDN'T COME LOOSE. USED PRY BAR. HAND WAS UNDER COVER TO CATCH. RESIDUAL AIR PRESSU RE FORCED COVER DOWN VERY RAPIDLY CAUSING INJURY TO LEFT HAND AND INDEX FINGER. MINOR SCRATCHES AND FINGER NEEDED STITCHES. (MIDDLE FINGER)