Buscar en el registro

Employee stated the following by phone on 3-10-04. Employee was pushing drill steel into the hole and felt pain in his right shoulder. He continued to work but felt pain while pushing the levers of the battery car he was operating. Started losing time from work 3-6-2004.

CREW WAS DRILLING A ROOF BOLT HOLE INTO MINE ROOF ALONG A NEW SLOPE. THE VIBRATION CREATED BY DRILLING CAUSED THE BOLTER TO CREEP A LITTLE DOWN THE SLOPE. THIS CAUSED THE STEEL TO BEND AGAINST SIDE OF HOLE. WHEN ATTEMPTING TO ADD A 2' EXTENSION OF DRILL STEEL EE'S FINGER GOT CAUGHT BETWEEN DRILL STEEL AND MINE ROOF AT COLLAR OF HOLE CAUSING INJURY. STARTED MISSING 5-7-03.

EE WAS USING THE DRILL PRESS TO DRILL OUT A BEARING. THE DRILL BIT HUNG UP CAUSING THE BEARING TO SPIN AROUND. THE DRILL BIT BROKE & THE BEARING FLEW OFF & HIT HIM IN THE LEFT PALM. 4 STITCHES REQUIRED.

MOVING MINER TO NEW LONGWALL. INJURED WAS USING NAIL GUN TO SHOOT WIRECLIPS INTO TOP. WHILE COCKING NAIL GUN IT DISCHARGED INTO LEFT PALM AND FRACTURED A BONE IN 4TH FINGER.

LIFTING APPROX 21' DRILL STEELS TO JOIN ADDITIONAL STEEL WHILE DRILLING BEGAN LOSING TIME 11-26-01.

EE WAS PREPARING NAIL GUN TO SHOOT NAIL INTO SALT FORMATION. THE GUN DISCHARGED DRIVING PLUNGER INTO PALM OF RIGHT HAND. THIS INJURY REQUIRED 2 STITCHES.

HELPING MECHANICS TO CHANGE SCRUBBER TANK AGITATOR. AGITATOR MOUNTED, ATTEMPTING TO REMOVE SHAFT CLAMP, CUT BOLTS WITH TORCH, CLAMP SWUNG OUT STRIKING FINGER AGAINST PIPE HAND RAIL. STITCHES R EQUIRED AND BROKE BONE IN FINGER TIP.

EE WAS DRILLING HOLES INTO MINE ROOF & INSTALLING 1' BOLTS WITH CLIPS TO SUPPORT THE CONVEYOR BELT. HE REACHED FOR BOLT WRENCH & ACTIVATED THEVALVE FOR STABILIZER BAR THIS LOWERED STABILIZER A GROUZER ON THE BAR CAUGHT FOOT, CAUSING A PUNCTURE WOUND & FRACTURING BONE IN BIG TOE STARTED LOSING TIME 2/13/01

EE WAS BOLTING BACK WHEN THE DRILL STEEL BECAME STUCK IN THE TURN TABLE WHILE ATTEMPTING TO LOOSEN THE STEEL SHE TWISTED/SPRAINED LEFT THUMB. SHE WAS SENT TO DR ON 1/17/01 FOR XRAYS-THESE WERE NEGATIVE. SHE CONTD TO HAVE PROBLEMS, WAS TAKEN TO DR 2/7/01 BECAME A RESTRICTED DUTY WORK INJURY AT THIS TIME

EMPLOYEE WAS MOVING ROOF BOLTER BACK FROM FACE AREA. THE REAR OF THE MACHINE WAS GETTING VERY CLOSE TO FACE FAN AND RIB ON LEFT SIDE OF ENTRY.HE SPLIT THE TRAM LEVERS TO MOVE THE REAR OF THE BOLTER AWAY FROM THE RIB. IN DOIN SO, HE PINNED HIMSELF AGAINST THE RIB WITH THE LEFT FRONT OF THE BOLTER, INJURING HIS FOOT.

EE WAS INSTALLING ROOF BOLTS IN ARE 512 WEST. WHILE MOVING THE ROOF BOLTER FROM ONE BOLT LOCATION TO ANOTHER, THE BOLTER SWUNG TO THE LEFT AND THE STABILIZER BAR STRUCK THE INSIDE AREA OF HIS RIGHT FOOT ANKLE.

EE WAS MOVING MINER, SETTING UP FOR NEXT CUT,INJEE SAW THAT THE MINER WAS ABOUT TO RUN INTO THE FACE FAN, HE REACHED FOR THE TRAM CONTROLS TO MOVE FAN BEFORE HE COULD MOVE FAN THE BOOM OF THE MINER STRUCK & MASHED HIS LEFT HAND INJURING THERING & LITTLE FINERS. STARTED LOSING TIME 4/21/00

EE WAS INSTALLING ROOF BOLTS IN AREA 310, WHEN A SPARE DRILL STEEL THAT WAS LAYING ON THE PLATFORM FOR VALVE BANK ROLLED OFF AND BECAME WEDGED BETWEEN BOOM AND FRAME. WHILE REMOVING STEEL HE S MASHED HIS LEFT INDEX FINGER BETWEEN THE DRILL STEEL AND FRAME OF BOLTER.

HE WAS CLEANING PIPE WITH AN ELECTRIC GRINDER WITH A WIRE BRUSH SO HE COULD WELD. THERE WAS POOR VENTILATION AND A RUST CLOUD FORMED AROUND THE WORKERS. A PIECE OF RUST WENT INTO EE'S RIGHT EY E. EE WAS WEARING EYE PROTECTION WITH FULL FACE SHIELD.

CUT INTO AN AIR POCKET WITH EIMCO MINER, WAS STRUCK ONTHE TOP OF HIS HARD HAT BY SOME MATERIAL FROMTHE BLOW AREA.

EMPLOYEE ATTEMPTING TO PRIME A PNEUMATIC PUMP THAT HAD LOST ITS PRIME. PUMP PRESSURED UP AND TYGON TUBING SEPARATED AT CONNECTION SPRAYING CLOROX SOLUTION INTO EMPLOYEES EYES AND FACE.

EMPLOYEE WAS USING A PNEUMATICE DIE GRINDER TO DEBUR A MOTOR HOUSING. EMPLOYEE STATED TO SUPERVISOR THE NEXT MORNING THAT HE HAD WHAT SEEMED TO BE A FOREIGN OBJECT IN HIS RIGHT EYE. EMPLOYEE T AKEN TO PHYSICIAN THEN TO OPTHAMOLOGIST FOR REMOVAL OF FORIEGN BODY. NO SIGNIFICANT DAMAGE IS EXPECTED TO EYE.

EMPLOYEE WAS HOLDING AN IRREGULAR SHAPED PIECE OF METAL WITH CHANNEL LOCKS WHILE GRINDING. IT FLIPPED UP & CUT HIS FINGER OF LEFT HAND. FOUR STITCHES WERE REQUIRED. THE TOOL RESTS WERE PROP ERLY ADJUSTED.

HE WAS USING AN IMPACT WRENCH TO REMOVE SOCKET HEAD CAP SCREWS THAT HAD BEEN WELDED IN PLACE. WHEN WELDS BROKE LOOSE, IT LEFT A SHARP EDGE THAT CUT HIS HAND WHEN TRYING TO REMOVE BOLT FROM ALL EN SOCKET.

WHILE CLEANING A GRINDER WITH AN AIR HOSE TRASH BLEW IN BEHIND EE S SAFETY GLASSES AND GOT INTO HIS RIGHT EYE CAUSING AN ABRASION TO THE OUTER LENSE. RECE3IVED A PRESCRIPTION OF POLYTRIM OPTH SOLUTION ON MAY 21, 1990.

WALKED UNDER A DOWNPOUR OF POTASH. THE POTASH WENT THROUGH THE SAFETY GLASSES AND INTO RIGHT EYE.

CUTTING BROKEN FLITE OUT OF BOTTOM SIDE OF SHUTTLE CAR. FLITE WAS BEHIND IT WITH PRESSURE. WHEN CUT IT TURNED LOOSE, STRIKING EMPLOYEE IN THE UPPER RIGHT SECTION OF HIS CHEST. CAUSED A 1 1/2" LACERATION.

INJURED WAS DRIVING RUBBER TIRED DOZER TO THE SHOP FOR REPAIRS, AND WAS NOT WATCHING WHAT HE WAS DOING. HE DID NOT LOWER HIS HEAD WHEN GOING UNDER AN AREA OF LOW ROOF. HE BUMPED HIS HEAD. THE INDIVIDUAL DID NOT GO TO THE DR UNTIL 2-6-89 ANDWAS GIVEN MEDICATION ON THIS DATE BY THE CO PHYSICIAN. INDIVIDUAL DID NOT START LOSING TIME UNTI 2-7-89.

EMPL WAS FIDING COLUMN UP TO CONNECT TO IRONWORK KNEE HIT A CLIP ON THE MAIN COLUMN CAUSING FOOT TO BE TWISTED

EMPLOYEE WAS REPAIRING AUGER HEAD.IN THE PROCESS OF BLOCKING UP THE AUGER HEAD,TO MAKE SURE THE AUGER AND BLOCKS WERE SQUARE,HE GOT OUT OF CAB.ON REENTRY HE LOST HIS FOOTING,FALLING FORWARD HE REACHEDOUT TO REGAIN HIS BALANCE.IN DOING SO MOVED LEVERS CAUSING THE MINER TO SET ON HIS LEFT FOOT.

KNEELING ON FLOOR USING DISC GRINDER TO BUILD TOOL-BOX,EMPL LAID GRINDER ON FLOOR OF SHOP WHILE GRINDER DISC STILL IN MOTION,EMPL CONTACTED WITH KNEE.

WHILE OPERATING FLETCHER ROOF BOLTER EMPLOYEE WAS DRILLING HOLES IN BACK FOR ROOF BOLTS. HE HAD FINISHED DRILLING HOLE AND WAS TAKING STEEL FROM HOLE. HE HAD LEFT HAND ON SECOND STEEL WEDGING IT AGAINST SIDE OF HOLE TO GETFIRST STEEL LOOSE. HE PUSHED BOOM LEVER WRONG WAY & CAUGHT LEFT THUMB IN HOLE.

ROY WAS WORKING ON AIR DOORS IN AIR COURSE HE CUT PIECE OF 8 IN CHANNEL AND WEDGED IT BETWEEN TWO BEAMS STOPPED TO CUT A 12 IN PIECE OF PIPE THE CHANNEL COOLED AND DROPPED STRUCK CROSS BEAM AND STRUCK HIM ON LEFT LEG CHANNEL WAS 30 IN LONG

FRANK PITMAN WAS PUTTING UP BELT CLIPS IN A-141 CALDERON WAS HELPING HIM WHILE DRILLING BOLT MACHINE MOVED CAUSING HOLE TO BE DRILLED OFF CENTER MACHINE WAS ON INCLINE WHILE PUTTING BOLT IN HO LE IT CAME OUT OF WRENCH CALDERON PUT BOLT BACK IN WRENCH AND MOTIONED TO FRANK WITH A NOD OF HEAD FRANK THOUGHT HE WANTED HIM TO PUSH BOLT UP AND DID SO AND CALDERONS FINGER WAS CAUGHT BETWE

DOZING UNDERPASS AT HEAD ROLLER 3RD 141 WITHY 9080 DOZER WAS LOW & TRANSFER MUCKED IN DOZER BUCKET HUNG ON FLOOR AND PUSHED OPERATORS HEAD UP INTO UNDERPASS GUARD SHOULDER SSTRAIN OR SPRAIN

CUTTING GALVANIZED GRATING AND INHALED SOME FUMES.DR DID NOT PERFORM PULMONARY FUNCTION TEST ...NECESSARY TO DIAGNOSE ZINC OXIDE POISONING-DIAGNOSIS BASED ON PATIENT HISTORY ONLY.EMPL ILL ON R EPORTING TO WORK.

EMPLOYEES WERE ROOF BOLTING IN AREA 141 USING A GALIS BOLTER. THEY WERE ATTEMPTING TO REMOVE SECTIONAL DRILL STEEL FROM A HOLE. THE STEEL GOT IN A BIND BETWEEN THE HOLE AND TURNTABLE ON THE GA LIS. GILLOCK WAS HOLDING THE STEEL AND BOATWRIGHT RAISED THE TURNTABLE TO FREE THE BIND. A PIN AT THE CONNECTION BETWEEN TWO SECTIONS OF DRILL STEEL CAUGHT GILLOCK\S GLOVE AND PULLED HIS FING