Esta búsqueda
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
EE sustained a contusion to the right forearm and minor swelling when the drill rod fell from above striking EE after the yoke cotter pin broke connecting the mainline and the rod while laying the rod on the rod rack.
LOWERING MAST TO MOVE TO NEXT SITE, THE MAIN LINE GOT CAUGHT UNDERNEATH THE TAILGATE. THE MAIN LINE CAME UNSTUCK AND FLEW, HITTING EMPLOYEE IN THE FACE.
EMPLOYEE WAS CLEANING VEHICLE WITH CLEANER. EMPLOYEE TRIED TO UNCOIL STEAM RUBBER HOSE. EMPLOYEESPRAYED HIMSELF ON THE LOWER RIGHT LEG WITH HOT WATER. RECEIVED SECOND DEGREE BURN TO LOWER RIGH T LEG.
HE WAS USING A 3/4 DRIVER RATCHET WITH 1 1/2 SOCKET TO OPEN OR REMOVE FILL PLUG TO DRAIN OIL FROM A 777C TRUCK. THE SOCKET SLIPPED AS HE WAS PULLING THE HANDLE DOWN. HE SMASHED HIS FINGER WITH THE RACHET HANDLE ON THE WHEEL.
EE WAS REPLACING A LIENR IN A CONVEYOR CHUTE. EE INSERTED TH BOLT STHROUGH THE CHUTE AND A CO-WORKER WAS PULLING ON TEH NUTS AND TIGHTENING THE LINER. EE PUSHED A BOLT THROUGH THE LIENR THAT THAD A SHARP EDGE ON THE BOLT HEAD. WHEN THE CO-WORKER APPLIED THE NUT AND STARTED SPINNING THE NUT WITH AN IMPACT WRENCH THE BOLT SPUN IN EE'S HAND CUT HIS RIGHT THUMB. NO LOST TIME.
EE WAS BREAKING UP CONCRETE USING A #60 JACKHAMMER. HE HAD ON STEEL TOED BOOTS, FACE MASK, SAFETY GLASSES, AND FOOT GUARDS. EE WAS USING FOOT TOSUPPORT JACK HAMMER. INJURY CAUSED BY CONSTANT RUBBING AND VIBRATION ON FOOT AND ANKLE.
EMPLOYEE WAS REMOVING OLD TUBES FROM A HEAT EXCHANGER. A 6' BY 2" TUBE WAS BEING CUT OFF WHEN IT FELL STRIKING EMPLOYEE'S RIGHT HAND CAUSING HIM TO DEPRESS OXYGEN LEVER ON CUTTING TORCH BURNIN G LEFT FOREARM. THERMAL 2ND/3RD DEGREE BURN. ABOUT 3" X 2" MIDPOINT VENTRAL SIDE LEFT FOREARM.
DIRT GOT INTO EYES WHILE EMPLOYEE WAS IN AREA WHERE SANDBLASTING WAS BEING DONE.NO IMPAIRMENT-EYES WERE CHECKED,IRRIGATED AND RIGHT EYE PATCHED.
EMPLOYEE WAS ALLEGEDLY OPERATING LOOPER WHEN SHUTTLE WENT FORWARD & THE PUNCHES DID NOT COME DOWN LIKE IT WAS SUPPOSE TO OPERTAOR KNEW IT WAS THE LIMIT SWITCH OPERATOR THEN RESACHED IN THRU A HOLE TO ADJUST THE LIMIT SWITCH UNDERNEATH WHEN HE DID THIS THE PUNCHES CAME DOWN SHUTTLE AUTOMATICALLY RETRACTED ALLEGEDLY PINCHING OR SQUEEZING EMPLOYEES WRIST BETWEEN THE SHUTTLE & FRAME
EMPL WAS CLOSING SLIDE GATE OF #2 ROASTER #1 CALCINE DISCHARGE PORT. ROASTER WENT POSITIVE CAUSING HOT CALCINE TO PUFF OUT BURNING BOTH LEGS.
EMPL WAS OPERATING LOOPING MACHINE. HE HAD TO PULL HANGER BAR OUT OF DEFECTIVE STARTER SHEET. HE ALLEGEDLY GRABBED BAR JERKING IT SMASHING FINGER BETWEEN BAR & BAR CARRIER.
EMPL CLAIMS HE WAS ATTEMPTING TO REMOVE A PIECE OF TRIM THAT WAS CAUGHT BETWEEN THE DISCHARGE ROLLER AND THE CUTTING WHEELS HIS GLOVE GOT CAUGHT PULLING HIS FINGER IN BETWEEN THE TWO ROLLERS C AUSING NAIL AVULSION OF THE L RING FINER