Buscar en el registro

Employee was diagnosed with a fractured wrist from an incident that occurred on 11/11. EE refused medical treatment at the time of incident. The employee was removing a lower roller when a bolt snapped, during loosening, causing the roller to push the hydraulic wrench and employees hand backwards. Employee continued to work until asking to seek medical attention due to swelling.

The employee was crimping hose fitting. As employee adjusted the feral, employee's foot inadvertently stepped on the deadman switch pinching two fingers. The employee was wearing gloves.

EE was dressing up an old road area by pushing dirt into a 3ft. washout when the blade aired out tipping toward the right front corner of blade causing the dozer to stop. Upon the verification that EE was wearing seatbelt correctly and because of EE's tall height and thin build allowed upper body to lunge forward causing head to hit the window latch.

EE was winching a generator into place (about 1 ft.) up to the Landoll Dropdeck Trailer to be loaded onto the trailer by an excavator when the chain connected to the generator in which the winch cable was hooked to broke.

Employee was operating pipe fusing machine. EE placed EE's hand on the hydraulic clamp to readjust. At the same time, using EE's other hand, EE operated the controls to close the clamp. The inside of EE's thumb was pinched between the pipe clamp and clamp support.

While grinding a weld off the bed of the dump truck utilizing leather gloves, repositioned ee to a squatting position while grinding in left hand requiring constant hand pressure, lost balance and caught himself with right hand on the deck of the dump truck. The grinder struck the floor and moved striking the top of right hand

Employee was using a hyd. jack with a 100lbs. metal spacer on top. When jack pressure was released the spacer fell hitting employees hand.

Employee was pressure washing a tractor. The tip of the pressure washer became clogged, and the employee swiped his hand over the tip of the wand and the pressure that was built up in the hose released and discharged water cutting his finger.

EE was grinding overhead and the grinding wheel came/broke off and cut through face shield, knocked eye safety glasses out of alignment and hit left eye

Two pumpers were connecting 6" pipe. The track hoe was connected to the opposite end of the connection. After communicating his intentions, the other pumper began to align the gasket. As he aligned the gasket, the track hoe operator was startled by material movement behind him. This made him hit the machine's swing, causing the two pipes to touch, pinching the employee's wrist.

He was using 6" boring equipment on the right outboard propel when the event happened. With the equipment on EE misplaced his hand causing it to become wedged between the smooth tube mount and the smooth drive drum. The distance between the tube and the drum is approx. 5/8". The employee was transported to the ER where he received 7 sutures to his right hand.

Employee was replacing cutting edges on a D6H Dozer blade. He was using a 3/4 inch impact with his right hand and his left hand was on top of the blade stabilizing himself. One of the plow bolts spun out and cut his left thumb - through his mechanic impact glove.

The operator was unloading the Cat 324D track hoe from the low boy trailer. When the operator got the machine to the back of the trailer he lifted the bucket off the ground and the track hoe tipped over on the boom side of the machine. The low boy was parked on uneven ground.

Employee was grinding in a small compartment when a flying particle entered his right eye.

Crew decided to place a rope spool on its side. As crane operator lifted, per signal person, top of load began to slighly lean towards the crane. Load was steadied by tagline. As he attempted to exit area, the bottom of load slid towards outrigger, hitting him in back of leg. The motion pushed his leg against outrigger, causing it to be pinched between the two.

Installing a carrier assembly in the right rear final drive. After I got the carrier assembly on the final I used the boom to hold the carrier assembly in place as I worked the carrier assembly inward. After the carrier assembly was bolted up I went to retract the boom and hit the work switch on the boom control. It swung the end of the boom into my face.

After grinding, the employee wiped his eye with his sleeved forearm. A small metal particle was found by the eye doctor in his eye.

Crew changing-out hoist ropes on 2570 W. Rope slipped free...swung forward and hit EE in the chest... throwing him backwards into the bucket pin. Rope hit EE from shoulder to hip and an abrasion in mid back.

An air motor on a lube pump tube had malfunctioned. The mechanic sprayed oil on the pistons to free them up. When he reattached the air line, the pump started running. His thumb was caught between the piston and the motor housing.

Operator of machine working in rough terrain when machine broke over a hump of dirt causing sudden jarring drop causing operator to receive upper back strain.

Employee was cutting trees 2" in diamiter. This particular tree was being cut 6" above his head. The weight & momentum if the saw caused him to swing down letting the saw come in contact with his leg. Causing him to hit his leg with saw.

THE EE WAS USING A 4 1/2" PORTABLE GRINDER DURING THE DAY. HE WAS WORKING IN THE CHUTE @ 2A TO 4 CONVEYOR ALSO @ THE TAIL OF #4 BELT. SOMETIME DURING THESE OPERATIONS, 2 METAL PARTICLES GOT IN TO HIS LEFT EYE. HE DID NOT NOTICE ANY IRRITATION UNTIL AFTER SHIFT WHEN HE WAS WASHING HIS FACE. THIS COULD HAVE CAUSED THE METAL TO BECOME STUCK IN HIS EYE. HE WAS WEARING CO. ISSUE SAFETY

EE WAS GRINDING WITH A 4 1/2" GRINDER. THE EE STATES THAT HE IS UNSURE WHAT HAPPEN. ON FURTHER INVESTIGATION THE GRINDER WAS FOUND TO HAVE A WIRE WHEEL BEING USED TO CLEAN BOLTS. IT APPEARS AS THOUGH THE GRINDER KICKED-BACK. EITHER THE EE ATTEMPTED TO CATCH THE GRINDER WITH HIS FREE HAND OR THE GRINDER KICKED BACKINTO HIS HAND. HE ALSO STATED THAT IT HAPPENED SO FAST HE WAS UNSURE.