Cyril Rock Quarry: 39 citaciones de la MSHA Metal/Non-Metal

Welders were replacing a section of flooring on the catwalk on the east side of the 5X14 screen and had cut an approximate 1' diameter hole. EE stepped onto the hole and lost his balance and fell. He struck his right shoulder on the handrail or screen, fracturing arm bone.

EMPLOYEE WAS USING A HOSE TO CLEAN UNDER THE JAW BELT CONVEYOR WHICH IS TWO FEET OFF THE GROUND. HE WAS STANDING BELOW & TO THE SIDE OF THE HEAD SECTION OF THE 5 1/2 DISCHARGE BELT & THE TAIL SECTION OF THE 5 X 14' CONVEYOR. THE BELTS WERE OPERATING & A ROCK FELL FROM ONE OF THESE BELTS APPROXIMATELY 10' & STRUCK HIS BACK. HE IS LOSING TIME.

EE STRAINED HIS BACK WHILE CHANGING SCREENS ON THE 5X14 DECK.

EE WAS CHANGING SCREENS ON THE 4 X 12 SHAKER. A SCREEN BECAME WEDGED AND WHILE HE WAS ATTEMPTING TO PULL IT LOOSE, HE INJURED HIS LEFT WRIST AND ARM.

EE JUMPED OVER A FOUR FOOT WALL TO GAIN ACCESS TO THE OLD SHOP FLOOR. HE STEPPED ON A BOLT AND TWISTED HIS ANKLE.

ON 7 FEB. 2003, EE COMPLETED AN ACCIDENT REPORT CLAIMING THAT HIS BACK WAS INJURED WHILE OPERATING A QUARRY TRUCK ON 20 JAN. 2003. HE DID NOT SAY ANYTHING ON 01-20-2003 AND WORKED THROUGH 1-28-03. HE TOOK OFF PART OF 1-28-03 AND 1-29-03TO MOVE HIS FAMILY OUT OF THEIR HOUSE. ON 1-30-030 HE COMPLAINED THAT HIS SEAT WAS BOUNCING. A MECH. CHECKED SEAT DROVE THRU 2-3-03 W/O COMPLAIN

EMPLOYEE WAS WORKING WITH OTHER EMPLOYEES TO TAKE THE CRUSHER APART. WHILE PUTTING A HOOK IN A LIFTING EYE, THE HOOK SLIPPED AND SMASHED HIS 4TH FINGER.

EMPLOYEE WAS REMOVING ROCK BY HAND FROM DIS- CHARGE BOX. A ROCK ROLLED AND CAUGHT HIS FINGER AGAINST ANOTHER ROCK.

EE WAS WORKING WITH OTHER EES TO LOAD BORE HOLES FOR BLASTING. EE LAID DOWN ON GROUND TO CHECK 2 BORE HOLES FOR WATER. HE PLACED HIS LEG IN FRONT OF RIGHT FRONT WHEEL OF PRILL TRUCK. WHEN THE PRILL TRUCK PULLED FORWARD TO THE NEXT HOLE, IT RAN OVER HIS LEG.

EE WERE UNBOLTING HEADACHE RACK ON TRUCK TO LOWER IT. WHEN LAST BOLT WAS REMOVED IT FELL ON TOP OF EE.

EMPLOYEE WAS USING A BAR TO LINE UP BOLT HOLES ON A SHAKER UNIT. HE STRAINED HIS BACK.

EE WAS ASSISTING ANOTHER EE IN PREPARING A PLATE FOR INSTALLATION INTO A CONE CRUSHER. HIS FOOT SLIPPED OFF THE PLATE AND HIS STRUCK THE PLAT. NO LOST TIME--STITCHES WERE REQUIRED.

EMPLOYEE ALLEGES THAT HE WAS WORKING ON A MOTOR FOR A TEREX TRUCK WHEN PAIN STARTED IN HIS BACK.

HE STRAINED HIS BACK WHILE PULLING WEEDS.

EE STEPPED IN A HOLE AT THE LOADER PARKING AREA.

HE TWISTED HIS SHOULDER WHILE LIFTING METAL. HE DID NOT REPORT ACCIDENT TO SUPERVISOR UNTIL 1-11-99.

HE STRAINED HIS BACK WHILE TAKING JETS OUT OF A WATER PUMP.

EE WAS PUTTING V BELTS ON A SHAKER UNTI. WHEN THE COUNTERWEIGHTS IN THE SHAKER GOT TO THE TOP, IT WENT ON OVER SMASHING THE MIDDLE FINGER ON HIS LEFT HAND.

AS HE STEPPED FROM HIS VEHICLE, HIS BACK CAUGHT ON THE TOOL BOX DOOR. HE SUFFERED A 5 INCH LACERATION ON HIS LEFT UPPER BACK.

WHILE BOUNCING ON UNI-LOADER ALL DAY, HE STRAINED A MUSCLE IN HIS LOWER ABDOMEN/ GROIN AREA.

LOADER OPERATOR SAID THAT STEERING HAD A JERK IN IT & CAUSED HIS BACK TO BE JARRED REOCCURRENCE OF 12-21-87 ACCIDENT FIRST DAY OFF 07-20-92

MECHANIC WAS KNOCKING OFF A WORN LOADER BUCKET TOOTH WITH A HAMMER AND A PIECE OF METAL CHIPPED OFF AND CUT HIS RIGHT LEG.

GRADER OPERATOR WAS HELPING MECHANIC WITH LOADER BUCKET TEETH AND HIT TOOTH WITH HAMMER TO DRIVE IT ON AND A PIECE OF METAL CAME OFF TOOTH AND CUT HIS LEFT LEG.

VICTIM WAS CUTTING HOLE TUBING WITH KNIFE BY PULLING KNIFE TOWARD HIS BODY WHEN IT STRUCK HIS LEG.

EE STATES HIS BACK WAS SPRAINED FROM CONSTANT JARRING FROM ROCK BREAKER.

FIRE BROKE OUT IN SECONDARY PART OF PLANT STARTING AT 4' DISCHARGE CONVEYOR. EIGHT CONVEYORS WERE AFFECTED. PLANT WAS CLOSED AT TIME. CYRIL FIRE DEPT WAS NOTIFIED BY PUBLIC AT 5:17 PM. THEY AR RIVED AT 6:00 PM.

INSTALLING TILT CYLINDER PIN IN LOADER HAMMER HEAD GLANCED OFF LOADER LEVER ARM STRUCK LEFT RING FINGER.

EMPLOYEE WAS PUTTING HYDRAULIC OIL IN LOADER HOSE BURST ON PUMP EMPLOYEE FELL BACKWARD FOOT CAUGHT IN LADDER.

EMPLOYEE WAS CL9ANING AIRLESS PAINT GUN BY RUNNING THINNER THROUGH IT, WHEN HE PUT HIS HAND IN FRONT OF THE SPRAY NOZZLE, LACERATION OCCURRED AND THINNER WAS INJECTED UNDER HIS SKIN.

OPENING STORAGE3DOOR TO GET A NEW CABLE SIDE OF CRANE HAD BROKEN LOOSE FROM THE BOTTOM ALLOWING THE DOOR TO PULL THROUGH

EMPL SLIPPED OVER FEEDER MOTOR AND TWISTED LEFT KNEE.

EE WAS CHANGING AN OXYGEN BOTTLE. HE WAS ATTEMPTING TO LIFT THE B OTTLE FROM A WELDING TRUCK & STRAINED HIS LEFT INGUIAL AREA.

EE WAS KNOCKING SHEAVE OFF GRIZZLY SHAFT & WHILE SWINGING SLEDGE HAMMER, HE MISSED THE SHEAVE & MASHED THE MIDDLE FINGER OF HIS RT HAND.

EMP WAS DOWN INSIDE GRIZZLY CHANGING BARS AN EMP WAS CARRYING PLATES DOWN TO HIM AND SOME ROCK GOT KICKED OFF INTO THE EMPLOYEE DISLOCATING HIS RT SHOULDER

EMP WAS MOVING A BATTERY OUT OF A 988 LOADER AND HE WAS STANDING IN THE WRONG POSITION WHICH CAUSED HIM TO STRAIN HIS BACK MUSCCLES

EMP WAS REMOVING HYDRAULIC LINE HE LAID DOWN ON THE PIPE AND PULLED THE WRENCH HE WAS USING WITH BOTH HANDS THE W R ENCH BRUISED HIS CHEST

EMPLOYEE WAS CHANING SPEED REDUCER ON 7\ REJECT CONVEYOR AND PULLED A MUSCLE IN HIS BACK.

THREE EMPLOYEES WERE ATTEMPTING TO SPLICE A DISCHARGE CONVEYOR BELT WHEN A PIECE OF METAL ENTERED THE LEFT EYE OF THE BELOW MENTIONED EMPLOYEE

EMPLOYEE WAS WALKING ON A ROCKY SURFACE AT THE PLANT AND STEPPED WRONG ON THE SURFACE CAUSING HIM TO THROW HIS BACK OUT OF PLACE

EMPLOYEE WAS PULLING A BEARING AND HOUSING OFF A 5 X 14 WITH A PORTA POWER JACK, WHEN THE BEARING CAME OFF THE SHAFT, THE PORTA POWER FELL AND STRUCK THE TOP OF HIS RIGHT FOOT.

SERVICING LOADER ON OUTSIDE OF SHOP,CRAWLED OVER TIRE TO CHECK MOTOR OIL.TIRE WAS WET,SLIPPED AND FELL HEAD FIRST,FOOT GOT HUNG UP ON BATTERY BOX.