Avísenme cuando se presente un nuevo incidente de la MSHA en Mine No 64.
EMPLOYEE WAS PICKING UP A ROOF BOLT & IT HAD A SHARP PIECE OF METAL STICKING OUT AND IT WENT THROUGH HIS GLOVE AND CUT HIS HAND.
EMPLOYEE WAS CLEANING UP AROUND THE TRACK & A TIE CAME UP ON ONE END & HIT HIM BELOW THE LEFT EYE
EE WAS OBSERVING A CONVEYOR CHAIN BEING REPAIRED WHEN OPERATOR STARTED THE CHAIN THE END OF THE CHAIN CAME OUT AND HIT EE.
EMPLOYEE WAS STANDING TOO CLOSE TO A SHUTTLE CAR CABLE & GOT HIT ON THE BACK OF THE LEGS
EE WAS HELPING MAKE A BELT SPLICE GOT HIS BELT CAUGHT ON A PLY CURTAIN.
EMPLOYEE WAS LOOSENING A BOLT ON A MOTOR WHEN HIS SOCKET SLIPPED CAUSING HIM TO FALL AND TWIST HIS ANKLE.
38920EMPLOYEE AWARDED A 7% HEARING LOSS,CLAIM #92-51844.
54736YEE WAS HELPING PUT AN ATRS SYSTEM ON A BOLTER AND GOT HIS FINGER CAUGHT BETWEEN ATRS AND THE BOLTER.
ROOF FALL IN INTERSECTION 3 CROSS CUTS OUTBY THE PILLAR LINE
EMPLOYEE WAS PULLING A SHUTTLE CAR CABLE AND FELT A SHARP PAIN IN HIS BACK.
EMPLOYEE WAS HELPING UNLOAD A BELT ROLLER AND CAUGHT HIS HAND BETWEEN ROLLER AND PORTAL BUS.
EMPLOYEE WAS HELPING LOAD MINE CABLES ON A SCOOP AND PULLED A MUSCLE IN HIS BACK.
EMPLOYEE WAS TRYING TO GET AN OLD PIN OUT OF AN AUGER CHAIN.A PIECE OF METAL FLEW OFF HIS HAMMER AND STRUCK HIS RIGHT INDEX FINGER.
EMPLOYEE WAS HELPING LIFT A PIECE OF BELT STRUCTURE AND A PAIN HIT HIM.
WALKING TO ANSWER PHONE SLIPPED AND PULLED LOWER BACK
ROOF FALL OCCURRED IN THE #1 INTAKE BROWN'S CREEK SIDE-WATER FAULT AREA-25' INBY SURFACE IN #3 ENTRY 18' TO 20'LENGTH 30' TO 40' WIDTH 4' TO 6' HEIGHT 6' COAL SEAM FIRECREEK.
BURSITIS IN SHOULDER WHEN HE SHOVELS COAL
EE WAS PULLING ON A SET OF COME LONGS WHEN THE CHAIN BROKE A LINK AND HIT HIM IN THE MOUTH.
EMPLOYEE WAS HELPING SPLICE BELT. A ROPE DOGE SLIPPED OFF AND HIT EMPLOYEE IN THE HEAD.
EMPL UNLOADING RAIL FROM FLAT CAR CAUGHT LEFT THUMB BETWEEN RAILS.
FALL OCCURRED IN INTERSECTION SPAD 458 INTAKE ENTRY DUE TO FAULT WATER COMING THRU TOP FALL APP 5FT THICK WIDTH 18FT LENGTH 4 0FT AREA ORIGINAL SUPPORTED 4FT DOUBLE BACK SHALE STRATA AREA NO I NJURIES
FALL OCCURRED AT SPAD 39 AIRWAY IN AN INTERSECTION 20'X30'X6'HIGH. THE FALL WAS DISCOVERED ON AN WEEKLY AIRWAY EXAMINATION. #1 ENTRY HOURSE BACK PRESENT IN AREA. BETWEEN 12 NOON 1-19-91 TIL L 10 PM 10-21-91.
EMPLOYEE WAS LIFTING A ROLL OF BELT ROPE.
LOADING SUPPLIES ON FLAT CAR TWISTED KNEE
2 BREAKS INBY SPAD 712 AFFECTING INTERSECTION FACE AREA FAULTY AREA STRATA STARTED CUTTING DURING CONTINUOUS MINER CUT. CREW WAS RETREATING CONT MINER & FALL COLLAPSED ONTO 1036 JEFFERY CONTIN UOUS MINER. NO PERSONS INJURED NO VENTILATION AFFECTED 4'5' & 5' DOUBLE BOLTS USED IN AREA.
FALL OCCURRED ON 3RD EAST PANEL APPROX 9:15 AM APPROX 1 B REAK OUTBY 704 SPAD 18' IN WIDTH & APPROX 35' IN LENGTH. NO VENT AFFECTED NO EQUIPMENT INVOLVED NO PERSONS INJURED.
EMPLOYEE BENT OVER TO MOVE A TIMBER AND FELT SHARP PAIN IN HIS BACK.
#2 ENTRY PARALLEL WITH SPAD 514 EXTENDING APP 420' FALL OCCURRED ON NORTHWEST MAIN EVALUATION INDICATED. WATER PRESENT DURING ADVANCING THIS AREA. FAULTY TOP. HEIGH OF FALL RANGED FROM 5' T O 8' IN H 17 TO 18' WIDTH NO VENT DISTRIRB NO TRAVELWAY BLOCKED.
EMPLOYEE WAS HELPING TO LAY TRACK AND PULLED HIS BACK.
EMPLOYEE WAS HELPING REPLACE A TIRE ON A SHUTTLE CAR.
EMPLOYEE WAS REMOVING CABLE FROM A HANGER WHEN THE HANGER DROPPED & CUT HIS HAND
UNLOADING STRAPS, CUT FINGER
EMPL WAS SHOVING ROOF STRAP ACROSS BOLTER WHEN STRAP CUT FINGER ON LEFT HAND,
WORKING IN SM CRAMPED AREA FELT BAD PAIN IN LOWER BACK
LIFTING BOLTER HEAD EMP FELT PAIN IN LOWER BACK
WHILE PUTTING A GUARD ON HIGH LINE CABLE,PIECE OF MUD FELL AND HIT EMPL IN EYE CAUSING CORNEAL ABRASION OF LEFT EYE.
WHILE OPERATING SHUTTLE CAR EE HIT A ROUGH SPOT CAUSING HIM TO BOUNCE UP AND AS HE FEEL DOWN ON SEAT HE HURT HIS RIGHT TESTICLE.
WHILE CARRYING A 5 GALLON BUCKET OF WATER EMPLOYEE FELT PAIN IN HIS RIGHT SIDE.
MOVING METAL BOXES INIDE OF MINES EMP MASHED L HAND BETWEEN TWO BOXES.
WHILE LIFTING SPILL BOARD ON BELT TAILPIECE EE FELT PAIN IN LOWER BACK.
ROOF FALL OCCURRED 001-0 SECTION ,4BRKS OUTBY FACE AREA SPAD #73 AREA OF BELT DRIVE.DIMENSIONS WERE 3-6' THICK X 23'WIDE X 50'LONG.4' & 5' DOUBLE LOCK BOLTS USED IN THIS AREA ALONG WITH METAL STRAPS.