Avísenme cuando se presente un nuevo incidente de la MSHA en Alma No 2 Mine.
| Trimestre | Horas trabajadas | Citaciones | S&S | Por 1M hrs |
|---|---|---|---|---|
| 2021 Q2 | 0 | 0 | 0 | |
| 2021 Q1 | 0 | 0 | 0 | |
| 2020 Q4 | 0 | 0 | 0 | |
| 2016 Q4 | 0 | 0 | 0 | |
| 2016 Q3 | 0 | 0 | 0 | |
| 2016 Q2 | 0 | 0 | 0 | |
| 2016 Q1 | 0 | 0 | 0 | |
| 2015 Q4 | 0 | 0 | 0 |
Injured EE and another EE were setting timbers underground, injured EE strained a muscle in his shoulder while lifting timbers.
While making the weekly examination for this non-producing mine a fall was observed at the crosscut #14
EE, Mine Foreman was making the required weekly examinatin for Non Producing Status when he discoverd a fall had occured in the Intake--3crosscuts from spad #257--appx 25ft long and 19 ft wide and 2 ft thick. This fall was reported at appx 8:52 am
Water was in the return, needed to set a pump to get the water out. Mine is Non-Producing at this time. EE carried a P40 pump, approx 60 lbs. He carried it approx 100'. He continued to work his regular job without incident. Management was not aware of this incident until 5/13/09. EE said he thought the pain was from old injury and did not report this accident to management.
HAD ROOF FALL ON THE BELT LINE APPROX. 8FT TO 9 FT THICK, 1 BREAK INBY SPAD #94.
HAD A ROOF FALL IN PRIMARY ESCAPEWAY, SET JACKS AROUND FALL. WE RE-ROUTED THE AIRWAY AND PUT AIR LOCK DOORS UP.
DRAW ROCK FELL, SWUNG POT OVER ON KNEE.
INTERSECTION FELL OUT, WE SET JACKS ALL AROUND FALL.
Employee lifting on conveyor motor on buggy, had a sharp pain on left side of back.
Cross Cut fell out on 1st left panel in the return, Spad # 215. We set jacks around the fall.
Cleaning up cut rock fell from top in conveyor ran back come off side & hit miner man.
# 29 crosscut fell in approx. 8' to 9' thick. No equipment involved. Crib off all four corners on 1st right mains, moved mandoor to # 28 break.
Employee stated he was getting belt tools from the belt line and the belts came on.
Employee was starting to drill hole and a piece of draw rock fell on his shoulder.
Moving miner from #4 entry to #5 entry and the rib rolled off while he was moving the miner and hit him in the hip.
Employee was getting his tools off the mantrip and rock hit him in the back of the head twisting his neck sideways and making a popping sound in his neck he stated.
Employee was hanging miner cable and felt a pain in his neck and shoulder.
Employee was cleaning tailpiece and the anchor pin pulled loose and hit him in the leg.
The Employee was walking thru # 4 cross cut and the Rib popped off hitting him in the head and nose area.
Employee was drilling in the 4R cross-cut and a piece of draw rock fell out hitting him on the hand and arm.
Employee was helping on the bolter and a piece of draw rock fell and hit him on the arm. He did not go to the hospital
The # 2 entry cross cut fell in at spad 200. We set built cribs and set timbers.
Found roof fall during Pre-Shift in the # 4 Entry on Section.
Had a fall in the intake. There was no one injured. Move stopping line over and set timbers and dangered off.
Was carrying box of glue and had pain in lower back.
Drilling hole for anchor pin to anchor the tailpiece.
Employee was reaching down to pull a miner cable for the power move.
Letting belt off after splicing belt, when chain hit his right forearm.
When coming out of Entry #1, buggy slid into rib. EE's arm was pulled between shuttle car and rib.
Hooking pull rope on boom and mashed against rib.