Esta búsqueda
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
EMPLOYEE WAS CUTTING AN OLD TOOL BOX FROM BACK OF HIS VEHICLE WHEN THE LID CAME DOWN AND SEVERED HIS RT.HAND, LITTLE FINGER FROM THE FIRST JOINT.
EMPLOYEE WAS INSTALLING LIGHT BRACKET AND ADJUSTING BOLTS. THE SWITCH BOLTS SLIPPED AND CAUGHT LEFT HAND BETWEEN LIGHT SWITCH AND L GROOVE.
MINER HAD BEEN MOVED ACROSS PANEL ON NIGHT SHIFT, BUT CABLE HADN'T BEEN HUNG UP. 2 EE'S WERE HANGING MINER CABLE ACROSS THE ENTRIES, THE BACK IN THAT ROOM MEASURED 78"-84". EE STATED THAT HE F ELT BURNING SENSATION IN HIS GROIN AREA.
A PIECE OF 1/4" MILD STEEL PLATE 32"X 60" WAS BEING LOADED ONTO A WELDING VEHICLE. THE STEEL WEIGHED APPROX. 136 LBS. THE PLATE WAS LIFTED UP & LEANED AGAINST THE VEHICLE. EE PICKED UP THE EDG E THAT WAS AGAINST THE FLOOR TO SLIDE IT ONTO THE VEHICLE & HE FELT A SMALL TWINGE IN HIS BACK.
EE WAS UNLOADING BELT STRUCTURE FROM BELT SKID. WHILE RAISING UP; PICKING UP A STAND HE TURNED TO THE LEFT TO PLACE STAND NEXT TO BELT & HIS LEFT KNEE POPPED & GAVE OUT. HE STOOD UP & FLEXED H IS LEG BACK & FORTH. WHEN HE CLIMBED OVER THE BELT HE FELT A SHARP PAIN. THE KNEE BEGAN SWELLING & PAIN WAS FELT WHEN HE WOULD PUT WEIGHT ON IT. HIS KNEE WAS ICED & HE WAS TAKEN TO ER.
EE WAS HELPING TO INSTALL NEW ROPE AN #1 HOIST. EE USING A 2X12 BOARD UNCONTACT WITH SPOOL TO ACT AS A BRAKE. NEW ROPE WAS ATTACHED TO OLD ROPE USING 7/8" CHOKER WITH EYES CUT OFF AND TWO 1 3/ 4" CABLE CLAMPS ON EACH ROPE END. HOIST USED TO PULL NREW ROPE OVER CROWN SHEAVE & INTO HOIST HOUSE. THE CONNECTION GOT CAUGHT ON I BEAM, SOME 12-14' BELOW CROWN SHEAVE, ROPE FELL OFF SHEAVE.
EMPLOYEE BENT OVER TO PICK UP FULL WATER BOTTLE AND AS HE LIFTED HE FELT PAIN IN HIS LOWER BACK.
EE WAS PULLING 1 1/2" RUBBER HOSE UNDER THE D-40THICKENE TO THE 50'U/F WASHOUT. EE WAS PULLING THE HOSE AT HIS SIDE WHEN HE FELT A SHARP PAIN IN HIS LOWER BACK.(RX FOR PHYS.THERAPY DAILY FOR ONE WEEK).
EE WAS EXAMINING A 2'X 2"X 1/4" PIECE OF ANGLE STEEL. AS EE TURNED IT OVER THE RACK WAS JARRED AND A PIECE OF 2"X 2"X 1/4" PIECE OF SQUARE TUBING FELL FROM THE TOP RACK AND STRUCK EE ON RIGHT HAND AND THUMB GOT CAUGHT BETWEEN AND RECEIVED LACERATION TO RT. THUMB REQUIRING SUTURES.
EE WAS USING AN ARC TO REMOVE STEEL FRO AN OLD WELDING SKID TO REBUILD SKID FOR ANOTHER USE. HE HAD REMOVED A PIECE OF 8" DIAMETER PIPE 19" LONG. AS HE STOOD IT UP ON END AND CONTINUED TO CUT ANOTHER PIECE, THE WELDER LEAD WAS BEHIND THE PIPE AND KNOCKED THE PIECE OF PIPE OVER. IT FELL &STRUCK VICTIM'S LEFT FOOT BEHIND THE STEEL TOE OF HIS BOOT CAUSING A FRACTURE TO HIS BIG TOE.
WHILE OPERATING THE MINER IN AREA 8, EE STATES HE WAS USING THE CABLE HOOK TO MOVE THE MINER CABLE TOWARD HIM USING HIS LEFT ARM. HE STATED HE FELT A PULL IN HIS LOWER BACK.
EE RIGGED A CHUCKER THRU ONE OF THE HOLES INT HE BACKUP RING ON THE FLANGE OF THE PIPE. HE SIGNUTED THE GRADELL OPERATOR TO PULLT HE PIPE OUT OF THE WAY TO BE ABLE TO GRAB THE INSTRUCMENT EE G RABBED INSTRUCTMENT T WITH HIS R HAND AND SIGNALTHE OPERATOR TO PULL THE PIPE ALL THE WAY OUT. WHEN THE PIPE CHEARED THE BOTTOM. FLANGE, IT ALLOWED THE PIPE TO TELT OVER. WHEN THE PIPE KILLED
EE WAS PULLING THE CALL BELL TO RELEASE THE SOUGHT CAGE AT #5 SHAFT AND HIS HAND STRUCK GREAST VENT THAT WAS INSTALLED IN THE GATE HINGE. THIS RESULTED IN EE RECEIVING A SMALL LACERATION TO BA CK OF RT. HAND THAT REQUIRED STITCHES. EE ABLE TO RETURN TO NORMAL DUTIES.
EE WAS IN THE PROCESS OF RECOVERING FLOOR MOUNTED BELT STRUCTURE ONT HE 700 LEVEL NEAR AREA 23. THE FLOOR STANDS WERE PARTICALLY BURN IN THE MUCK SO HE AND CO WORKERS WERE PUSHING AND PULLING ONE EACH STAND TO LOOSEN THEM SO THEY COULD BE PICKED UP. WHEN EE PULLED ON THE STAND HE FELT PAIN IN HIS RIGHT SHOULDER.
EE STATED HE LIFTED A TWO PIECE METAL PLATE GUARD COVER ON #693 DC SHUTTLE TO SEE HOW MUCH CABLE WAS LEFT IN CABLE REEL.WHILE LIFTING THE LEFT GUARD COVER TO UPRIGHT POSITION AND WHILE ATTEMPT ING TO LIFT THE OTHER GUARD COVER THE COVER ON LEFT SIDE FELL. EE GOT HIS LEFT HAND CAUGHT BETWEEN COVER DOOR AND SHUTTLE CAR RESULTING IN LACERATION THAT REQUIRED SUTURES.
EE HAD BEEN TIGHTENING BOLTS ON GEAR CASE AND LOADING OXYGEN TANK ONTO MANTRIP IN AREA 5. EE FELT PAIN IN HIS LOWER BACK.
EE WAS REROUTING CONDUIT. AFTER MOVING CONDUIT EE WAS ATTEMPTING TO CLAMP CONDUIT WHEN CONDUIT SLIPPED & PINCHED INDEXFINGER HE GOT L INDEX FINGER CAUGHT BETWEEN CONDUIT & THE HANDRAIL CAS UED LACERATION THAT REQUIRED SUTURES.
EE PICKED UP TWO BUCKETS OF BITS AND CARRIED THEM TO THE FRONT OF THE MINER. WHEN EE STARTED TO SET THEM DOWN, HE FELT SHARP PAIN IN THE MIDDLE OF HIS LOWER BACK AND BEGAN HAVING MUSCLE SPASMS .
REMOVING CONCRETE FORM FROM SHAFT. WHILE BREAKING FORM FROM CONCRETE, FORM BROKE LOOSE FROM CONCRETE AND STRUCK EE ON THE RIGHT ARM. LACERATION TO ARM BELOW ELBOW THAT REQUIRED STITCHES.
EMPLOYEE WAS DRYING A 400 ML GRIFFEN BEAKER WHEN HE CUT HIS FINGER ON CHIPPED EDGE. LACERATED RIGHT RING FINGER, REQUIRING 2 SUTURES.
EE WAS SLIDING A SMALL WORK TABLE OVER. THERE WAS A STEEL PLATE APPROX 12" X 12" RESTING ON THE TABLE. WHEN EE WENT TO MOVE TABLE, STEEL PLATE FELL OFF TABLE STRIKING EE ON TOP OF R FOOT WHICH CASUED A PUNCTURE/LACERATION TO TOP OF FOOT THAT REQUIRED 3 SUTURES. ON 8/15 EE WAS UNABLE TO WEAR BOOT AND BECAME RESTRICTED TO THE OFFICE.
EMPLOYEE WAS CHANGING MINER AREA 4 AND WAS LOADING USED BITS ONTO MANTRIP AND FELT PAIN IN HIS LOWER BACK.
EE STATES THAT HE HAD PERFORMED HIS JOB DUTIES WHICH INCLUDED LOADING CABLE ONTO A SLED & DROPPING PULL CORD CABLE FROM HEAD OF DRIVE WORKING TOWARD TAIL ROLLER. THEN AFTER LUNCH HE STATES H E FELT PAIN IN RIGHT LEG WHEN WALKING. REQUESTE TO SEE DR ON 3/16/00 BECAME RESTRICTED 3/21/00 Y Y
EE WAS ADJUSTING ON A SCREW GATE GOING TO THE #1 100'. AS EE WAS TIGHTENING GATE, HE COUGHED AND FELT PAIN IN HIS LEFT GROIN.
AS EE WAS ENTERING THE CAGE AT #2 SHAFT ON THE 800 LEVEL, THE CAGE BEGAN TO MOVE UPWARD. EE PULLED THE DOOR LATCH TO CLOSE THE DOORS. LATCH WAS DIFFICULT TO RAISE IN THE POSITION HE WAS IN. EE STRAINED TO MOVE LATCH THAT RESULT IN LOW BACK PAIN.
WHILE OPERATING A LOADER THE EE STEPPED OUT OF THE LOADER TO TALK TO A TRUCK DRIVER. WHEN EE STEPPED BACK INTO THE CAB, HE ALLEDGEDLY HURT HIS BACK. THIS EE HAS HAD A HISTORY OF BACK PROBLEMS.
AS EMPLOYEE REACHED DOWN TO PICK UP NYLON STRAP ON THE TRAILING CABLE OF THE MINER TO MOVE IT OUT OF THE WAY, EMPLOYEE PULLED CABLE WITH LEFT ARM WHILE OPERATING REMOTE WITH RIGHT HAND LOADING RAM CAR. HE FELT PAIN IN HIS LEFT SHOULDER.
EMPLOYEE WAS HELPING CHANGE OUT A SHAKER SCREEN. AS COVER TO SCREEN WAS MOVED, EMPLOYEE GOT FINGER CAUGHT BETWEEN SCREEN AND COVER.
AS EMPLOYEE WAS BENDING OVER TO REMOVE THE BELT GUARD ON THE TAIL ROLLER OF #2 BELT, SHE FELT PAIN IN HER LOWER BACK.
EE WAS INSTALLING CABLE TRAY WHILE EE WAS LIFTING TRAY WRIST CAME IN CONTACT WITH SHARP EDGE & CUT WRIST
EE PINCHED RIGHT INDEX FINGER BETWEEN AN OUTRIGGER AND A BLOCK WHILE TRYING TO BLOCK UP THE OUTRIGGER TO TRAVEL TO THE SHOP FOR REPAIRS.
WHILE ATTEMPTING TO OPEN THE FACE OF HIS CAP LAMP TO CHANGE THE LIGHT BULB, THE EE TWISTED THE LAMP & HEARD A "POP" IN HIS RIGHT HAND
THE EE WAS LIFTING AN APPROX 50 LB ROLL OF CURTAIN STRIP. AS HE LIFTED, HE FELT A PAIN IN HIS LOWER BACK.
A STRUCTURAL WELDER WAS WORKING ON THE HAND RAILS OF NORTH STAIR TOWER OF THE HEAVY MEDIA BUILDING. EE LEANED ACROSS THE TOP RAIL AND PULLED UP ON THE LOWER RAIL TO MAKE A FIT BEFORE WELDING H ANDRAIL TOGETHER STRAINED RIGHT SIDE OF CHEST THAT REQUIRE A RX MED FOR DISCOMFORT. COME-A-LONG AND CLAMPS WERE IN THE AREA TO FIT HANDRAIL TOGETHER BUT HE CHOSE NOT TO USE THEM.
CREW WAS SETTING STRUCTURAL STEEL IN LOADING DOCKET @ 850 LEVEL. THE CHUTE SIDEPLATE WAS SET IN PLACE AND EE WAS PUSHING WITH HIS LEG TO ALIGN. WHILE PUSHING ON SIDEPLATE, HIS LEG BROKE.
EE TRIED TO CLOSE WATER VALVE. VALVE HANDLE BROKE. EE FEL AND HIT HIS ARM ON BORKEN VALVE HANDLE. HE WAS TRANSPORTED TO ER AND WOUND WAS SUTURED.
EE WAS ON THE OUTSIDE OF A CONTROLLER CABLE BOX PUSHING ON A CABLE TO GET THE CABLE THROUGH THE STRAIN RELIEF. THE RESISTANCE GAVE WAY JERKING THE CABLE FORWARD. THIS CAUSED THE EE TO LOS HIS BALANCE AND HE FELT PAIN IN HIS LOWER BACK.
EE WAS MAKING A HOSE ON THE HOSE MACHINE AND HIS HEADLIGHT HIT THE FLUORESCENT LIGHT, WHICH SHATTERED AND A PIECE OF GLASS WENT INTO HIS EYE.
EE HIT HIS HEAD ON A GREASE INJUCTOR WHILE CLEANING A BIN ROOM.
THE MINER CREW MOVED THE MINER AND PULLED THE SLACK CABLE OUT WITH A JEEP. AS THE EE WAS THROWING THE CABLE LOOP AGAINST THE RIB WITH A ROPE, HE FELT A PULL IN HIS LOWER ABDOMEN. THE EE CONTIN UED TO WORK UNTIL HE WENT TO A DR ON 9-9-98. AT WHICH TIME HE WAS DIAGNOSED WITH A HERNIA.
THE EE WAS TAKING DOWN OLD CURTAINS BY HAND AND AS HE PULLED ON A CURTAIN HE APPARENTLY WAS STANDING IN AN ANGLED POSITION AND PULLED A MUSCLE IN HIS BACK Y
THE HAULAGE TRUCK WAS SITTING HIGH, AND WHEN EMPLOYEE WENT TO GET INTO THE TRUCK HE PUT TOO MUCHWEIGHT ON HIS RIGHT KNEE AND STRAINED IT. THIS INJURY WAS NOT REPORTED TO US UNTIL 6.30.98.
EE WAS IN A FORKLIFT BASKET HELPING TO INSTALL A CHAIN HOIST (WEIGHING APPROX. 150 LBS.) ON A MONORAIL ON THE WEST END OF THE WET IMPACTOR DECK. A CRANE WAS HOISTING THE CHAIN HOIST, AND EE WA S LIFTING AND PUSHING THE HOIST ONTO THE MONORAI. HE FELT PAIN IN THE INNER ELBOW OF HIS RIGHT ARM.
EE HAD DESCENDED A LADDER INTO A TANK. AT THE FOOT OF THE LADDER, HE REALIZED HE HAD CUT HIS LEFT FORCARE ON THE SHARP EDGE OF THE TANK BAFFLE.
THE EE (A WELDER) WAS INSTALLING A ROLLED PIECE OF METAL ON THE OUTSIDE OF A DRYER TO ATTACH TO THE DRYER SHELL. HE WAS REMOVING AN L IRON CLAM AND AS HE WAS BENDING THE CLAMP TO BREAK IT LOOS E BY PULLING ON IT, HE FELT A PAIN AND HEARD A POP IN HIS RIGHT SHOULDER. THE EE CONTINUED TO WORK UNTIL 4-27, FIRST DAY LOST.
EE WAS LYING DOWN ON A METAL PLATFORM, WHILE GRINDING ON A WALL WHEN HE ROLLED OVER TO GET UP HE ROLLED OVER HIS BATTERY PACK 1 LIGHT PULLING A MUSCLE IN HIS LOWER BACK.
EE WAS WORKING ON THE BUCKET CONVEYOR & WAS REMOVING THE BRAKE FROM THE SPEED REDUCER. THE SPEED REDUCER ROLLED ON THE SHAFT & PINNED HIM BETWEEN THE I-BEAM & THE MACHINERY ITSELF.
TWO EMPLOYEE HAD PUT SEVEN DRUMS OF TRASH SAND ON WOODEN PALLETS AT ABOUT 6:00 PM. AFTER ONE EMPLOYEE GOT HOME THAT NIGHT HIS BACK GOT SORE AND STARTED HURITNG. ON 3/13/98 EMPLOYEE WENT TO THE DOCT. WITH HIS BACK. THE DOCTOR TOLD EMPLOYEE TO COME BACK TO WORK,ON LIGHT DUTY UNTIL HIS NEXT APPOINTMENT.
EMPLOYEE WAS MOVING THE BELT FOR THE CONTINUOUS MINER. AS HE LIFTED A TOP ROLLER, HE FELT PAIN IN HIS LOWER BACK. THIS WAS AN AGGRAVATION OF PRE-EXISTING INJURY.
EE WAS WORKING UNDER THE LOADER HEAD. AS HE CHANGED POSITIONS, THE BILL OF HIS HAT HIT THE UNDERSIDE OF THE LOADER HEAD AND KNOCKED A PIECE OF RUST INTO HIS RIGHT EYE.