Buscar en el registro

Load shifted and pinched EE's 2 fingers on right hand between the love joy plates.

EE hand was caught in the line of fire between cooler for crusher #2 and stationary I beam. EE sustained a laceration to left hand required 3 sutures to close the wound. EE had gloves on at the time of incident and work hazard assessment completed highlighting exposures and hazard mitigation plan.

Employee assisted by another employee repositioning roller back into CAT D6 Dozer. Load shifted causing 1 employee to bare burden of load. Employee treated conservatively by athletic trainer and worked at full capacity. Employee continued to have discomfort, MRI issued to discover rotator cuff tear. Surgery now scheduled.

Employee was pulling a 2" Thick x 10" W x 20' between mid rail and toe board. The board tilted causing hand to become caught between board and mid-rail.

Employee was welding, and it was hot outside. He wiped his face with a paper towel. Around 8 AM his right eye started to feel irritated. He asked a co-worker to flush his eye. He said it still felt like something was still in his eye. The employee was taken for medical treatment where a small particle was taken out of his eye.

Employee was getting a pipe from a material rack. When getting the pipe the one next to it shifted and pinched his pinky finger between the two pipes.

Attempting to install turbocharger on Co Id. #2339 Volvo water truck, when employee felt a pop/burning sensation in left shoulder region.

Miner was bending a belt lacer off and felt a pop in wrist.

The miner was securing a rubber screen blank to a rope when he lost grip of the rope releasing the screen. The miner attempted to catch the falling screen blank and put his body into an ackward position causing a strain to neck.

The employee was patching a conveyor belt and replacing some bad lacers. The employee reached around and to pull out one of the bad lacers, in which had a sharp edge, cutting his right index finger.

The miner was bending over to pick up a needle nosed plier off of a bench and proceeded to throw his back out.

Employee was helping to sort screens when the pile of screens shifted and hit his knee as he was trying to get out of the way.

EE WAS REMOVING A BELL PAN FROM UNDER A 980G. HE TOOK 3 OF THE 4 BOLTS OUT, WHILE REMOVING THE LAST BOLT, PAN FELL DOWN & HIT HIS KNEE.

EE WAS HELPING TO MOVE A BURNER. HE PUSHED THE BURNER TO RELOCATE HIS FINGER WAS SMASHED BETWEEN A WALL AND THE BURNER. (4 STITCHES).

EE WAS REPAIRING AN EQUALIZER ON DRY BULK TRAILER, EE WAS REMOVING A BLOCK OF WOOD FROM A JACK STAND THAT WAS SUPPORTING THE TRAILER FRAME, THE HYDRAULIC JACK SLIPPED ALLOWING THE FRAME TO DRO P, HIS FINGERS WERE PINCHED BETWEEN THE BLOCK AND FRAME.

EE WAS PUTTING A 3/4 OPENING WIRE CLOTH IN THE BACK OF A PICK-UP. HE PLACED HIS ARM UNDER THE SIDE OF THE SCREEN. WHEN THE SCREEN SLID IN HIS ARM WAS CUT.

EE WAS HANDING SCREENS FROM THE LIFT BASKET TO SOMEONE ON THE GROUND. HE LIFTED THE SCREEN OVER HIS HEAD AND HE HURT HIS NECK.

EE WAS INSTALLING A SCALE ON A STACKING CONVEYOR& WAS BENT OVER INSTALLING A WEIGHT ON SCALE. WHILE STRETCHING TO PERFROM THE TASK EE EXPERIENCED PAIN IN RIBS ON HIS LEFT SIDE Y

EMPLOYEE WAS WORKING AT THE STOCK PILE BINS OF OUR SECONDARY PLANT. HIS JOB WAS TO LOAD STOCK TRUCKS FROM THE HOLDING BINS. WHILE LOADING A TRUCK, THE CLAMGATE AT THHE BIN JAMMED. EE PULLED ON THE BIN LEVER AND TORE HIHS RIGHT BICEPS TENDON.

INJURY WAS NOT REPORTED TO SUPERVISOR UNTIL 1-24-95. EMPLOYEE WAS LIFTING A PUMP HOUSING ONTO THE MOUNTING SURFACE. EMPLOYEE DID NOT USE A COMEALONG AS HE WAS INSTRUCTED.

EMPLOYEE WAS SHOVELING PULVERIZED LIMESTONE TO CLEAN UP MILL AREA. HE SHOVELED ALONG WITH TWO OTHER EMPLOYEES WHO WERE NOT INJURED. HE NEGLECTED TO TAKE PROPER BREAKS AND CARE WHILE DOING HIS JOB.

EMPLOYEE WAS OPERATING BINS. THE CLAMGATE WAS DIFFICULT TO OPEN. HE USED EXCESSIVE FORCE & INJURED HIS BACK.

REPLACING DRIVE BELT ON MOTOR FEEDER.

PUTTING V-BELTS ON PRIMARY FEEDER USING FOOT TO HOLD UP WEIGHT.

PULLING 2A BIN WHILE IT WAS FROZEN SHUT. TRYING TO GET IT TO OPEN UP.

CLOSING BINS-GOT HIS THUMB BETWEEN HANDLE & BIN LEG

PUTTING SCREEN IN 5 X 16 SHAKER AND TWISTED WRIST.