Cada lesión y muerte que la MSHA tiene registrada. Filtra por estado, año, sector, clasificación, experiencia o cualquier palabra clave de la narrativa del investigador.
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
I WAS USING LIFTING JACK TO RERAIL TRACK JEEP WHEN I FELT SHARP PAIN IN MY GROIN AREA.
EE WAS USING A BELT KNIFE TO CUT CONVEYOR BELT IN PREPARATION TO INSTALL A SPLICE WHEN KNIFE SLIPPED AND STRUCK LEFT LEG APPROX. 2 1/2INCH ABOVE KNEE CAUSING A LACERATION. INJURY OCCURRED WHIL E SPLICING P-4 SECTION CONVEYOR.
EE AND OTHER WAS USING LIFTING JACK TO LIFT BELT CAR ABOVE TOP OF RAIL WHERE TRACK FROM ELEVATOR LANDING AND SLOPE LANDING INTERSECTS SO THAT THE UNDERSIDE OF BELT CAR WOULD CLEAR. WHEN BELT C AR BECAME FREE THE SLACK IN THE COUPLING CAUSED CAUSE JACK AN DBAR TO KICK OUT CAUSING DAMAGE TO EE RIGHT ANKLE AND FOOT.
EE AND COWORKER WERE SAWING COUPLING OFF OF END OF 6" AIR LINE THAT EXTENDED DOWN SLOPE TO SUMP AREA WHEN BOW SAW THAT COWORKER WAS USING SLIPPED AND STRUCK BACK SIDE OF HAND CAUSING A LACERAT ION.
EE WAS USING A 40 OZ. HAMMER WHILE WORKING ON AXLE. FOR MINE CAR WHEN HE STRUCK HIS LEFT MIDDLE FINGER WITH HAMMER.
EE WAS USING ROCK BAR TO PRY EE BY CHAIN INTO SPILL PLATE TRAVELWAY WHEN BAR SLIPPED AND CAUGHT EMPLOYEE'S 2ND FINGER LEFT HAND BETWEEN ROCK BAR AND SPILL PLATE.
EE & EE WAS LOSWERING WHEEL BARROW FROM DRYER FLOOR TO NEXT FLOOR USING CHAIN HOIST BLOCK ON HOIST HUNG & IN AN ATTEMPT TO RELEASE BLOCK AT LOCATION WHERE IT WAS HUNG EE RING FINGER ON LEFT HA ND WAS CAUGHT IN PINCH POINT
EMPLOYEE WAS PULLING ON A RATCHET WHEN HE STRAINED HIS LEFT SHOULDER. EMPLOYEE'S FIRST WORK DAY LOST BECAUSE OF INJURY WAS 10-13-94.
EE WAS HELPING SPLICE THE 6560 SEC. BELT AT THE TAIL PIECE WHEN THE BEL CLAMPS SLIPPE AND CAUGHT EE'S LEFT HAND CAUSING THE INJURY.
EE WAS CUTTING WIRE BAND FROM AROUND A BUNDLE OF ROOF BOLTS THE WIRE UNDER TENSION SPRANG LOOSE UPON BEING CUT AND STRUCK HIS KNUCKLE CAUSING A LACERATION
EE WAS ATTEMPTING TO PRY A ROCK FROM BETWEEN THE DUAL WHEEL OF A RAM CAR WHEN THE ROCK BAR SLIPPED & MASHED HIS LITTLE FINGER ON LEFT HAND
INJURED WAS STRIKING A STEEL WITH A SLEDGE HAMMER WHEN STEEL SLIPPED AND CUT HIS LEFT INDEX FIGNER.
EMPLOYEE WAS JACKING JEEP BACK ON TRACK WHEN THE JACK SLIPPED & EMPLOYEE FELL.
EE WAS UNLOADING ROLL OF BELT WITH ROCK BAR WHEN ROCK BAR SLIPPED & STRUCK FOOT
THE EMPLOYEE WAS DRIVING A BEARING ONTO MIENR WHEN HE HIT HIS THUMB WITH THE HAMMER.
EMPLOYEE WAS SPLICING TRAILING CABLE FOR ROOF BOLT MACHINE. USING CRIPPING TOOL TO CRIP LUG ON POWER LEAD WHEN A PIECE OF CRIPPING TOOL FLAKED OFF WHEN STRUCK WITH HAMMER & BECAME EMBEDDED IN HAND.
INJURED WAS CHIPPING FLUX OFF OF A WELD AND A PIECE GOT IN HIS EYE.
EMPLOYEE PLACED OPEN POCKET KNIFE ON TOP OF DUST BOX AND TURNED AND CUT HIS ARM ON IT.
EMPLOYEE WAS SPLICING 40 #2 CONNVEYOR WHEN BELT KNIFE SLIPPED AND CUT RIGHT LEG.
ANOTHER EMPLOYEE WORK HOLDING PANEL WITH ROCK BAR WHEN IT SLIPPED AND HIT HIM IN EYE.
EE WAS CUTTING A PIECE OF CONVEYOR BELT WITH A BELT KNIFE AND THE KNIFE SLIPPED AND CUT HIS LEG.
EMPLOYEE WAS TAPPING A UNIVERSAL JOINT ONTO A DRIVE SHAFT WHEN A PIECE OF METAL STRUCK HIM IN THE RIGHT FOREHEAD.
INJURED WAS USING A HAMMER ON A BELT PUNCH WHEN A PIECE OF METAL STRUCK HIS LEFT ARM.
EMPLOYEE WAS USING A LIFTING JACK TO LEVEL 10 SOUTH NO 1 CONVEYOR.A "T" BOARD HAD BEEN PLACED UNDER BELT ROPE TO HELP MAINTAIN BELT LEVEL.A PASSING SPLICE STRUCK T BOARD KNOCKING IT OUT AND ON TO EMPLOYEES RIGHT HAND CAUSING THE LACERATION.
BUILDING A STRIP BRATTICE,EMPL HIT TOP WITH HAMMER IT BOUNCED BACK AND HIT IN MOUTH.,
I NAME WAS HELPING REMOVE A LARGE ROCK OUT OF THE BELT CHUTE WHEN THE ROCK DISLODGED & CAUGHT HIS HAND BETWEEN THE ROCK & CHUTE
EMPLOYEE WAS HOLDING SPLICE AND ANOTHER EMPLOYEE HIT HIS FINGER WITH A HAMMER.
EMPLOYEE WAS WORKING ON A 4160 VOLT CABLE. HE WAS USING A BELT KNIFE TO CUT OUT A BAD PIECE OF CABLE. THE KNIFE SLIPPED AND CUT HIS LEFT HAND.
EE WAS TIGHTENING A BOLT ON THE TAIL ROLLER OF THE 910 NO. 2 CONVEYOR THE RATCHET HE WAS USING SLIPPED AND HIS MIDDLE FINGER RIGHT HAND STRUCK FRAME OF TAILROLLER CAUSING INJURY.
THE INJURED STATED THAT HE WAS CUTTING SOME HOLES IN A PIECE OF RUBBER BELT WITH A BELT KNIFE WHEN THE KNIFE SLIPPED AND CUT HIS LEFT THUMB CAUSING THE INJURY.
INSTALLING HANDLE IN TRACK HAMMER USING HAMMER HIT L INDEX FINGER
EMPL WAS USING HAMMER TO SEPARATE COUPLING LINK ON JACKHAMMER. HE HIT LEFT THUMB WITH HAMMER CASUING LACERATION. HAND WAS STATIONED ON PIECE OF METAL WITH SHARP EDGE WHEN IT WAS STRUCK WITH HA MMER.
EMPLOYEE WAS HELPING SPLICE A BELT AND MASHED HIS FINGER WITH THE BELT SPLICING TOOL.
OTHER WAS USING TORCH TO CUT COVER OFF OF BOOM OF CONTINUOUS MINER. THE TORCH DID NOT THOROUGHLY CUT COVER OFF OR SOME OF THE HOT METAL PREVENTED IT FROM FALLING OFF. OTHER WAS USING A HAMMER AND CHISEL TO FINISH SEPARATING COVERED WHEN A PIECE OF METAL STRUCK EE IN THE LEFT THUMB.
EE WAS USING A HAMMER TO DRIVE A BOLT OUT OF A CONVEYOR CHAIN ON A BRIDGE UNIT WHEN HE STRUCK HIS LEFT HAND WITH A HAMMER.
EMPL WAS PULLING ON COMALONG CHAIN WHEN COMALONGS SLIPPED OFF ROD THEY WERE HUNG ON. THEY STRUCK HIM ON HEAD CUTTING RIGHT EYEBROW.
THE INJURED EMPLOYEE WAS HOLDING WRENCH ON NUT ON MOTOR WHEN WRENCH SLIPPED HITTING HIM IN NOSE.
THE INJURED EMPLOYEE WAS USING ROOF BOLT TO DISLODGE BELT FROM SHIRT RUBBER WHEN IT SLIPPED AND CUT HIS HAND.
EMPL WAS JACKING BELT TAIL PIECE WITH LIFTING JACK USING BAR. HE WAS PUSHING BAR WITH FOOT FOOT SLIPPED OFF BAR CAUSING BAR TO FLY UP & HIT HIM IN MOUTH.
THE INJURED STATED THAT HE AND W NAME WERE CHANGING OUT SOME DEWATERING PADS IN THE DISCHARGE END IN THE BUMP CRAL WASH BOX I NAME WAS KNOCKING THE PADS INTO PLACE WITH A HAMMER WHEN THE HAMME R GLANCED OFF OF THE SIDE OF THE WASH BOX STRIKING HIS #2 FINGER CAUSING THE INJURY
THE INJURED STATED THAT HE WAS KNOCKING A BIT OUT OF THE HEAD ON THE #3 MAIN WITH A PUNCH WHEN A SMALL PIECE OF METAL CHIPPED OFF THE END OF THE PUNCH STRIKING THE INJURED IN THE CHIN CAUSING THE INJURY.
I N AME WAS HOLDING A PIECE OF STEEL AND ANOTHER EMPLOYEE WAS HITTING WITH HAMMER CAUGHT FINGER BETWEEN PIECE OF STEEL AND MINER.
THE INJURED STATED THAT HE WAS PUTTING A CABLE PULLER ON THE #3 MINE AND DROPPED IT ON HIS RIGHT FOOT CAUSING THE INJURY.
HE WAS ATTEMPTING TO FREE A DRILL STEEL FROM THE CHUCK BY USING A METAL PUNCH AND HAMMER. WHEN HE STRUCK THE PUNCH A PIECE OF IT FLEW UP AND STRUCK HIM IN THE EYE.
THE INJURED EMPLOYEE WAS USING SLEDGE HAMMER ON SHAFT TO KNOCK GEAR OFF AND CAUGHT HIS HAND ON SHARP EDGE.
THE INJURED STATED THAT HE AND (NAME) WERE TAKING THE PLUG OUT OF THE CUTTING HEAD OF THE #4 JOYSLIPPED OFF AND STRUCK THE INJURED ON THE 4TH FINGER LEFT HAND CAUSING THE INJURY .
THE DUMP CABLE 2N THE DRAGLINE BUCKET WAS CAUGHT IN THE DUMP SHEAVE EMPLOYEE HOOKED A CHOKER CABLE TO FREE THE DUMP CABLE THE CHOKER CABLE SLIPPED OFF AND STRUCK HIM ON THE ARM
THE INJURED STA7ED THAT HE WAS CUTTING A PIECE OF WIRE WITH A PAIR OF WIRE CUTTERS WHEN ONE END OF THE WIRE FLEW UP AND STRUCK HIM IN THE RIGHT EYE. CAUSING THE ACCIDENT.
INJURED EMPLOYE9 WAS LIFTING HYDRAULIC RAM CAR JACK WHEN IT SLIPPED OUT OF HIS HAND AND CAUGHT FINGERS AGAINST FRAME
THE INJURED STA7ED THAT HE WAS IN THE PROCESS OF TIGHTENING UP TWO CAP BOARDS OVER THE TOP OF A TIMBER.WHEN HE STRUCK THEM WITH A HAMMER ONE OF THE CAP BOARDS FLEW BACK AND STRUCK HIM IN THE M OUTH CAUSING TH9 INJURY.