Buscar en el registro

Hand was caught between pry bar and motor

Bar came loose striking employee in the right leg.

Employee was using a pry bar on the screen deck motor when the bar slipped hitting EE in the face.

Knife slipped cutting knee. Had to have stitches in knee cap

Splicing a belt on conveyor when the clamp slipped and cut left hand

Employee was using a pry bar to pry a tire off a rim.

Employee was cutting boxes, the knife slipped and cut his right index finger. Required 3 stitches. No restrictions, no lost time.

Employee was working on a truck and pulled lower back. Went to chiropractor, released with no restrictions. Received report in office 4/27/2009.

Employee was lifting drive shaft from loader with chain hoist. Weight shifted and caught finger between shaft and loader.

On 9/23, EE was trying to get a rock unstuck from a dozer. When swinging the sledge hammer, his hand hit the dozer arm. On 9/26, he went to the doctor and had X-rays. Put him in a cast and released him back to work with lifting restrictions. Will re-evaluate in 2 weeks.

Employee was digging rock out of the breaker when a rock broke loose and fell on his hand causing bruising. Went to doctor & had x-ray, nothing broken. Did not receive report in office until 7/14/2008

EMPLOYEE WAS SCRAPING LIME DUST THAT WAS STUCK ON THE INSIDE OF THE MAIN SCREEN BIN. HE STATED THAT HE TWISTED HIS BODY TO REACH A CORNER AND STRAINED HIS BACK.

EE WAS WORKING ON TIRES. TIRES WERE SPARES FOR TEREX 3305B. EE WAS ASSEMBLING A TIRE AND HOLDING LOCK RING UP WITH BAR. WITH HIS LEFT THUMB HE WAS PUSHING "O" RING INTO PLACE AND THE BAR SLIPP ED AND LOCK SNAPPED DOWN ON THUMB.

EE WAS WORKING ON THE FRONT SPRING OF A MACK TRUCK AND SWINGING A SLEDGE HAMMER. HE TWISTED HIS BACK RESULTING IN A PINCHED NERVE.

EE WAS REMOVING A GASKET FROM THE REAR END PLATE OF AXLE. THE GASKET SCRAPER HE WAS USING SLIPPED, CUTTING HIM ON THE LEFT HAND BETWEEN THE THUMB & FOREFINGER. REQUIRED 2 STITCHES.

EE WAS USING A JACK UNDER THE SCREENING PLANT AND JACK SLIPPED OFF OF BLOCK AND CAUGHT HIS FINGER.

EE WAS USING A SLEDGE HAMMER WHILE CHANGING HAMMERS IN THE HAMMERMILL. THE EE HIT HIMSELF WITH THE HAMMER IN THE LEFT LEG.

EE WAS TURNING FAN BLADES ON A CAT D8 DOZER AND HIS HAND GOT CAUGHT BETWEEN THE SHOVEL AND THE FAN BLADE.

EMPLOYEE WAS WORKING ON A LOADER BUCKET AND USING APORTA POWER TO HOLD REINFORCEMENT IN PLACE WHILE WELDING AND THE PORTA POWER SLIPPED PINCHING HIS LEFT INDEX FINGER CRUSHING THE BONE.

EE WAS ATTEMPTING TO REMOVE A LOCKING COLLAR ON A SPPED REDUCER WITH A PIPE WRENCH. THE LOCKING COLLAR SUDDENLY BROKE LOOSE AND EE FELL(APPROX 5 FT) AND LANDED ON HIS LEFT WRIST AND HIP.

EE WAS HOLDING ONTO AN HYDRAULIC HOSE WHILE ANOTHER EE WAS CUTTING IT WITH A POCKET KNIFE. THE KNIFE SLIPPED CUTTING VICTAM BETWEEN THE RIGHT THUM & FOREFINGER Y

EE WAS WORKING ON CHANGING SCREENS IN CEDAR RAPIDS SCREEN UNIT #1815. EE WAS PULLING ON A BOLT WITH A WRENCH, IN A HARD TO REACH PLACE AND PULLED A MUSCLE IN HIS SHOULDER.

EE WAS WORKING UNDER LOADOUT FEED BIN #220. TIGHTENING A BOLT. WHILE COMING OUT FROM UNDER EQUIPMENT HE STOOD UP TOO SOON & HIT HIS BACK JUST BELOW THE NECK BETWEEN SHOULDER BLADES ON CROSS MEMBER

EE WAS USING A BALL JOINT FORK TO SEPERATE BALL JOINTS FOR REPLACEMENT. EE HIT THE FORK AND IT CAME LOOSE STRIKING HIM IN THE LEFT ANKLE CAUSING A PUNCTURE WOUND.

EMPLOYEE WAS TIGHTENING THE SLACK ADJUSTER TO SET THE BRAKES ON THE TEREX HAUL TRUCK. THE WRENCHSLIPPED AND CAUGHT HIS FINGER BETWEEN THE WRENCHAND ADJUSTER. HIS FINGER WAS CUT, REQUIRINGSIX S TITCHES.

EMPLOYEE WAS REMOVING A TRANSMISSION COVER PLATEON A CAT D8L. HE WAS USING A SMALL COMBINATION END WRENCH. AS HE PUT PRESSURE ON WRENCH IT SLIPPED OFF AND WHEN IT DID HIS RIGHT ELBOW STRUCK THE SIDE OF FRAME. ELBOW SWELLED UP AND SOME FLUID BUILT UP. WILL RETURN TO DOCTOR AT END OF MONTH FOR CHECKUP.

EE WAS PRYING A ROCK THAT WAS ABOUT TO ENTER THE IMPACT CRUSHER. EE SAW THE ROCK NEEDED TO BE TURNED SO HE POSITIONED THE PRYBAR BETWEEN THE SIDE OF THE IMPACT CRUSHER AND THE ROCK. AS HE PULL ED, THE BAR SLIPPED. THIS CAUSED SOME DISCOMFORTIN HIS SHOULDER AREA. EE WENT TO DR. AND WAS TOLD TO TAKE TWO SAYS OFF.

EE WAS INSTALLING NEW RUBBER FLASHING ON A DISCHARGE BIN. HE WAS PULLING THROUGH THE RUBBER FLASHING WITH A PAIR OF VICE GRIPS. AS HE WAS PULLING, THE VICE GRIPS CAME LOOSE AND HIS RIGHT HAND SLID ALONG THE SIDE OF THE METAL PLATE THAT HOLDS FLASHING IN PLACE. HIS SMALL FINGER WAS CUT WHEN IT CAME IN CONTACT WITH PLATE. (1" LACERATION.)

EE WAS HELPING MOVE A LARGE ROCK FROM THE THROAT OF A CEDAR RAPIDS IMPACT BREAKER. HE WAS USING A LONG PRY BAR TO TURN THE ROCK SO IT WOULD EVENTUALLY DROP DOWN AND GO IN THE BREAKER. EE WAS S TANDING ON THE CATWALK COMPLETELY TO THE SIDE OF THE THROAT AS THE ROCK WAS TURNED IT WENT INTO THE BREAKER, FRAGMENTED THEN A SMALL PIECE HIT THE CHAINS AND BOUNCED OFF AND HIT EE.

EMPLOYEE AND OTHER EMPLOYEE WERE DRIVING OUT RACES ON A GD ROCK DRILL. EMPLOYEE HAD A HOLD OF PUNCH. AS EMPLOYEE HIT THE PUNCH A SMALL PIECE OF STEEL CAME OFF AND HIT EMPLOYEE IN THE INDEX FIN GER. EMPLOYEE HAD GLOVES ON BUT STEEL WENT THROUGH. BY THE TIME THE DOCTOR PULLED THE STEEL OUT EMPLOYEE NEEDED 2 STITCHES. PUNCH WAS APPROXIMATELY 7" LONG (SNAP ON).

EE WAS STRIPPING DOZER MECHANIC WAS LINING UP A HHOLE WITH A 4' PRY BAR. AS HE WA APPLYING PRESSUR EON TEH BA WHEN IT SLIPPED AND HIT HIM ON IN THE EYE. SUSTAINED A SMALL CUT AND BLACK EYE. EE WAS WEARING SAFETY GLASSES BUT HAD TAKNE THE HOLE UP. THIS WAS A UNSAFE ACT. THIS IS AGAINST COMPANY POLICY.

CHANGING SCREENS ON PLANT.

EMPLOYEE IS A WELDER AND WAS LINING A LOADER BUCKET WITH 1/4" STEEL. HE HAD POSITIONED THE STEEL IN PLACE ON THE BOTTOM OF THE LOADER BUCKET. USING A PORTA POWER AND 1" ANGLE IRON EMPLOYEE PU T DOWNWARD PRESSURE ON THE STEEL PLATE. AS HEAT WAS APPLIED TO THE STEEL EMPLOYEE TOOK A 10 LB. SLEDGE AND HIT THE STEEL PLATE. AS HE DID SO THE ANGLE IRON POPPED LOOSE AND HIT HIM IN MOUTH.

EE WAS REPLACING A DRIVE BELT ON A SMALL CONVEYOR BIN. HE HAD SET THE NEW BELT INTO POSITION AND PROCEEDED TO TURN THE HEAD PULLEY USING A PIPE WRENCH AND A CHEATER PIPE. AS EE WAS ROLLING THE HEAD PULLEY, THE CHEATER PIPE SLIPPED CAUSING EE TO LOSE HIS BALANCE AND FALL APPROX. 10' TO THE FROZEN GROUND BELOW. EE SUFFERED BRUISES TO HIS LEFT SHOULDER AND RIBS.

OPERATING A BREAKER WHENA LARGE ROCK STOPPED THE FLOW OF ROCK INTO THE FEEDER. THE ROCK WAS APPROX 2 1/2 FOOT THICK 3' WIDE AND 4' LONG AND WEIGHTED INT HE AREA OF 1500 LBS. INJURED TOO A 6' PRY BAR PROCEEDED TO PRY THE ROCK UP IN THE HOPES OF MOVING HT EROCK TO ANOTHER POSITION. AS HE WAS PRYING TH EROCK UP THE BAR SLIPPED OUT CAUSING HIS RIGHT FOOT TO MOVE FORWARD AGAINST A 4"

EMPLOYEE WAS REPAIRING FLOOR OF A LOADER BUCKET.A NEW SECTION OF STEEL FLOOR WAS BEING PRESSED DOWN WHITH A 10 TO PORTA-POWER. A CHAIN WAS SECURELY ATTACHED TO THE SIDES OF THE LOADER BUCKET. PORTA-POWER WAS POSITIONED BETWEEN THE CHAIN & SHEET OF METAL. INJURED PLACE HIS LEFT HAND ON TOP OF THE CHAIN ABOVE THE PORTA-POWER, WHICH SLIPPED. [SEE ATTACHED FOR REST OF NARRATIVE]

A 40 LB ROCK HAD WEDGED IN THE BREAKER. HE WAS LYING ON HIS SIDE TRYING TO PRY THE ROCK IN A DIFFERENT POSITION. HE WAS BENT OVER PULLING ON A PRY BAR WHEN HIS BACK POPPED. HE WILL BE IN- STRUCTED ALONG WITH THE FOREMAN NOT TO USE THIS PROCEDURE ANY MORE. THEY WILL BE INSTRUCTED TO USE A CHAIN AND LOADER TO EITHER PULL THE ROCK OUT OR TO CHANGE ITS POSITION.

9?514E IS IN CHARGE OF MAINTAINING CRUSHING PLANT. EMPL BACK BECAME SORE AT NO SPECIAL TIME. GRADUALLY OVER A PERIOD OF YEARS OF CLIMBING ON & OFF EQUIPMENT AND USING A PRY BAR. BACK HAS BECOM 50269E. I.NAME INSTRUCTED BY DR TO TAKE 2 DAYS OFF. I.NAME BACK TO WORK AND FEELING GOOD.

THE INJURED JUST FINISHED GREASING THE PLANT. HE FIRED UP ALL THE EQUIPMENT FOR THE CRUSHER PROCEDURE. HE NOTICED THAT THE TUB ON THE SCREENING PLANT WAS NOT TURNING SO INJURED TOOK A 6 FT B AR HOOKED THE FLAT END OF THE BAR ON A BOLT AND TRIED TO HELP THE TUB ROTATE. IN DOING SO THE BAR SLIPPED, HITTING INJURED ON THE SHOULDER. THE ACCIDENT WAS INVESTIGATED BY THE SAFETY DIRECT

THE PLANT WAS SETTING UP TO BEGIN OPERATIONS AFTER MOVING AND WAS SHUT DOWN AT THE TIME OF THE ACCIDENT THE INJURED PERSON WAS ADJUSTING THE SUPPORT BRACKETS FOR THE CONVEYOR BELT ON A BIN HE WAS STANDING IN THE BACK OF A PICK UP TRUCK USING A SOCKET RATCHET WRENCH WITH A CHEATER PIPE ON THE HANDLE OF THE WRENCH THE CHEATER PIPE SLIPPED AND HE FELL TO THE GROUND

HIT ON RIGHT LEG WITH SLEDGE HAMMER WHILE WORKING ON TRACK FRAME ON 155 KOMATSU DOZER

MECHANIC WAS BENDING A PIECE OF STEEL WHEN STEEL HIT MECHANIC IN HEAD