Buscar en el registro

Employee reported accident occurred while clearing plugged starter steel on drill rig. Compressed air had been used unsuccessfully to clear debris. Air was bled off Workers waited 2 minutes before trying to clear plugged steel with a pry bar. Plugged material came free, releasing residual compressed air, water, mud and debris onto worker's right hand and coveralls.

EE was using a snap-on filter wrench with a 24" breaker bar to loosen a filter the breaker bar slipped out of the filter wrench socket and his left elbow struck a strut housing. No reportable medical treatment until 7/12/07.

Reported pain after the job was completed. Returned to regular duty on 4-26-07.

Unknown. No specific event cited in the incident report. " Injury by useing hand tool"

A PIECE OF SPROCKET BROKE OFF, STRIKING EE IN THE NECK.

Employee reported using long handle scraper to clean accumulated material from floor of service pit. Scraper struck raise edge of 1/4" hidden under material resulting in jammed right shoulder. Employee did not seek medical attention until friday July 29th at 7 pm.

EE was laying on his stomach on top of 36" pipe. Reached over to adjust the come-a-long - was wearing rain suit. Slipped off the pipe, fell into a hole approximately 8' deep. Offered medical care - EE declined. Then requested care on 12-22-04.

BOX CUTTER SLIPPED, CUTTING EE'S LEFT KNEE.

THE WRENCH HE WAS USING SLIPPED, CAUSING EE TO FALL OF THE RAMP BACKWARDS.

STRAIN / INJURY BY USING TOOL.

BOX SLIPPED AT THE AREA BEING OPENED ABEL LOST BALANCE FELL BACKWARD, LANDING ON LEFT ELBOW & JAMMING LEFT SHOULDER

STRUCK BY FALLING OR FLYING OBJECT. EE WAS DRIV-ING PIN INTO TOOTH ON LOADER BUCKET WITH HAMMER,HAMMER STRUCK THE PIN-PIECE OF METAL FLEW INTO EE'S CHEEK/JAWBONE AREA.

CUT LEFT HAND WHILE CUTTING OLD BELT PRESS BELT PRESS BELT OFF. THE WEIGHT OF THE BELT PULLED HAND ACROSS KNIFE. SEVERAL STITCHES FOR 3 CM LACERATION. Y

CUT/PUNCTURE/SCRAPE. HOLDING DEVICE TO STABILIZETOOTH WHILE PIN WAS HAMMERED OUT.(ON LOADER) STEEL WENT INTO HIS ARM ON UNDERSIDE HALFWAY BETWEEN ELBOW AND WRIST.

CUT/PUNCTURE/SCRA--KNIFE SLIPPED AND CUT PALM OF LEFT HAND

EE STRUCK AMETAL OBJECT WITH HIS HAMMER AND A PIECE OF METAL LODGED IN HIS THUMB. METAL REMOVED ON 11-11. EXPECT COMPLETE RECOVERY WITH NO PERMANENT DAMAGE AT NEXT DR. VISIT ON 1-05-99.

EE WAS PULLING ON A WRENCH TO REMOVE A BOLT WHEN HE FELT A SHARP PAIN [SIMILAR TO A BEE STING] IN HIS FINGER. THE SKIN WAS NOT BROKEN. THE NEXT DAY THE FINGER BECAME SWOLLEN & THE REDNESS MOVE D UP HIS HAND.

THE TRACK ASSEMBLY (A LARGE HEAVY CHAIN) WAS LAID DOWN FLAT ON THE GROUND. THE LEADING CHAIN LINK BECAME FOULED AND HE WAS USING A BAR TO HELP THE CHAIN ADVANCE OVER THE OBSTRUCTION. THE CHAIN JUMPED OR SLID AND MADE CONTACT WITH HIS ANKLE.

EE WAS APPLYING PRESSURE TO A JACK OR "PORTO POWER". THE JACK BUCKLED AND STRUCK EE IN THE MOUTH.

AS EE WAS USING THE SLEDGEHAMMER TO REMOVE THE ROCK, A CHIP OF THE ROCK FELW OUT AND HTI HIS FINGE RAND CAUSIGN HIS FINGER TO BLEED.

EE WAS CUTTING A 3/8IN RUBBER GREASE HOSE WITH AN EXACTO-TYPE KNIFE. THE KNIFE CUT THROUGH THE HOSE EASILY AND MADE CONTACT WITH EE'S THUMB.

WHILE EE WAS OPENING RAILCARS, THE METAL BAR GOT STUCK & THEN HIT HIM IN THE MOUTH.

EE WAS TRIMMING A PLASTIC BED LINER FOR A TRUCK WITH A KNIFE AS HE WAS DOING SO THE KNIFE SLIPPED & HE CUT HIS FINGER

HE WAS USING A PRY-BAR. THE BAR SLIPPED AND THE SHARP END HIT HIM IN THE FOREHEAD.

EE WAS SING A WRENCH TO TAKE BOLT OUT OF A SCREEN WHILE HE WAS TAKING THE BOLT OUT OF THE SCREEN THE WRENCH SLIPPED & THE BOLT TURNED IN THE PALM OF HIS HAND

EE WAS CUTTING SOME PLASTIC PIPE USING A RAZOR KNIFE. AS HE WAS DOING SO THE KNIFE SLIPPED AND CUT HIS THUMB.

INJURED WAS SHOVELING IN A BUNKER DRAIN TROUGH.AS HE WAS SHOVLEING INJURED BUMPED INTO A GRATE WHICH WAS LEANING AGAINST THE WALL.THE GRATE FELL ON HIS FOOT.

I.NAME HAMMERING ON A BEAM.PARTICLE OF DIRT FELL IN EYE-WAS GIVEN A RX.

I.NAME PUSHING A PRYBAR AROUND A PIECE OF CONDUIT.COWORKER WAS ABOVE I.NAME ALSO PUSHING PIECE OF PRYBAR AROUND A CONDUIT.HE DROPPED THE PRYBAR AND IT BRUSHED AGAINST I.NAME.

STRIPPING WIRE (NORMAL JOB-RELATED DUTIES) AND KNIFE SLIPPED.

EMPLOYEE WAS WORKING ON A TRUCK WITH A SCREW DRIVER THE SCREW DRIVER SLIPPED AND PUNCTURED THE SKIN ON HIS LEFT HAND THE FOLLOWING DAY THE WOUND DEVELOPED AN INFECTION.

WHILE WORKING O3 A NEW BASE ROCK TUNNEL ON A CRANE TRYING TO OPEN UP THE LOCKING LEVER, A BAR SLIPPED AND HE BUMPED HIS ELBOW ON A FRAME CAUSING NUMBNESS OF THE THUMB AND THREE FINGERS.

INJ ASSEMBLING 5RMCO STEEL SECTIONS INTO A TUNNEL.A PRY BAR USED BY INJURED SLIPPED AND CAUGHT INJ FINGER AGAINST STEEL SECTION.

INJURED USING P3PE WRENCH WHEN WRENCH SLIPPED & CAUGHT FINGER.

INJURED HELPING TO UNLOAD RAILCARS WHEN THE BAR HE WAS USING SLIPPED AND STRUCK JAW CAUSING HAIRLINE FRACTURE OF JAWBONE

INJ SPENT 1K MINUTES REACHING UP AND SWINGING 10 LB SLEDGE HAMMER THEN LOWERED A LADDER INTO A BUNKER INJ THEN LOWERED A FIRE EXTINGUISHER INTO THE BUNKER INJ IS UNSURE WHICH ACTION CAUSED THE INJURY BUT THE ONSET OF LOWER BACK PAIN OCCURRED WHEN LOWERING THE EXTINGUISHER