Buscar en el registro

Employee was swinging a sledgehammer inside of a controlled environment garage.

While performing mechanical maintenance inside of a controlled environment garage, the employee used a sledgehammer to dislodge a brace when the sledgehammer broke the weld the iron angel spun and struck the base of the employees right thumb.

Working in the controlled environment of an enclosed garage when EE's hand slipped while installing a two-way radio into a company vehicle cutting hand between the thumb and pointer finger requiring stitches

During daylight hours in dry conditions the employee was attempting to loosen a bearing on a tail pulley with a hammer when employee struck the middle finger of left hand.

Employee was cutting zip ties off of plate press bags using a utility knife when they cut the palm of left hand requiring 3 stiches.

Using sledge hammer on drill step, missed step with sledge hammer and hit left hand; swelled immediately.

Employee was installing a discharge chute to a screen. Bolt holes did not line up. He inserted a pin pry bar to aid in lining up bolt holes. As he began to pry on chute, the pin pry bar slipped striking the employee in the forehead. He received 10 sutures.

EE was handling a large equipment jack when it slipped and cut his right middle finger. He recieved a couple of stitches and returned to work.

EE WAS CUTTING A BELT WITH A UTILITY KNIFE WHEN IT SLIPPED AND CUT THE HEEL OF HIS LEFT HAND.

WHILE THE MINER WAS TIGHTENING NUTS ON THE PRIMARY CRUSHER FEED HOPPER, THE RATCHET WRENCH SLIPPED OFF THE WORK AND CAUSED THE MANS RIGHT HAND TO STRIKE THE I-BEAM SUPPORT FOLLOWED BY THE RATC HET WRENCH ON TOP OF THAT. UPON XRAY 2 FINGERS OF THE RIGHT HAND WERE FOUND TO BE FRACTURED.

EE WAS LOOSENING UP PIPE FITTING ON CRUSHER, PIPE WRENCH CAME OFF AND STRUCK LEFT KNEE CAUSING IT TO SWELL UP. WENT TO WAYNE GENERAL OCCUPATIONAL HEALTH DEPT FOR TREATMENT

MECHANIC WAS HELPING CRUSHER OPERATOR CLEAR ROCK FROM CRUSHER JAW. MECHANIC WAS USING A LONG PRY BAR. BAR SLIPPED OFF ROCK AND CAUGHT HIS HAND BETWEEN BAR AND CRUSHER. MECHANIC TAKEN TO HOSPIT ALTO HAVE 12 STITCHES IN LEFT RING FINGER TIP, WILL GO BACK TO HOSPITAL 8-14-95, FOR FOLLOW-UP. NO LOST WORK TIME.

EMPLOYEE WAS TIGHTENING BOLT ON CRUSHER ROCKBOX WRENCH SLIPPED HIS ARM HIT A SHARP EDGE OF STEEL CAUSING A CUT ON HIS RT ELBOW (ABOVE JOINT) TOOK MAN TO ER IN HOSPITAL & THEY SUTURED THE CUT

EMPLOYEE STRAINED LUMBAR IN BACK WHILE PULLING ON WRENCH OVERHEAD. HE TOLD ME ABOUT WHAT HAPPENED ON MARCH 2 AND I TOOK HIM TO DR.DR. GAVE HIM MEDICATION & SAID HE COULD RETURN TO WORK AND SEE HIM AGAIN ON MARCH 6. MARCH 6 DR. TOLD HIM NOT TO WORK FOR 3 DAYS AND HE WOULD GIVE HIM THERAPY STARTING TOMORROW, MARCH 7.

MAINTENANCE MECH WAS INSIDE CRUSHER WORKING ON REMOVING A JAW PLATE FOR REPLACEMENT,COME-A-LONG HOISTS WERE FASTENED TO THE JAW BUT THE JAW WAS WEDGED IN THE FRAME.THE MAIN MECH WAS PRYING ON THE JAW WHEN SUDDENLY IT MOVED FORWARD PUSHING HIS LEFT LEG AGAINST THE OTHER CRUSHER JAW.THE MAN WAS ABLE TO FINISH HIS SHIFT BUT AT HOME HIS LEG PAINED HIM,WENT TO HOSPITAL WHERE THEY FOUND

EMPLOYEE WAS DRIVING A RETAINER PIN INTO A TOOTH ON THE BUCKET OF 988 LOADER THE HAMMER HE WAS U SING GLANCED OFF THE TOOTH AND STRUCK HIM IN THE LEFT KNEE THE INITIAL PAIN WENT AWAY BUT THAT SAME EVENING THE PAIN INCREASED AT 6;30 AM THE FOLLOWING MORNING HE REPORTED FOR WORK BUT WAS SENT TO THE HOSPITAL FOR X-RAYS FOTHING BROKEN BUT KNEE IS BRUISED WRAPPED WITH ACE BANDAGE AND T