Buscar en el registro

While working on IR Drill pounding out a pin with a hammer, metal fragment broke off and cut into the palm of employees right hand.

While pulling on a wrench with left hand and pushing the ratchet with right hand to tighten a bolt for a v-belt guard on screen 31, employee felt his shoulder pop. Possible shoulder strain/sprain.

While working with two other employees ratcheting a come-a-long to lift a ripper claw, the chain on the come-a-long broke and the ripper claw fell and hit employee above the right knee.

While changing screens on screen #5, employee began pounding the wedge down on the screen when pieces of metal flew into his left eye. Employee was wearing safety glasses, however they were not the appropriate type for the work he was doing.

EE was assembling a hammer assembly for an air track drill. EE was attempting to screw the nut on a long bolt to hold the assembly together when the hammer dropped and smashed EE's finger on his right hand.

While standing on the rock shelf in C-13 head box cleaning build up with a long hooked rod, EE felt a pain in lower back.

While using a chisel and hammer to remove broken grease fitting from the rock buster hammer (equip# 2514) a foreign metal piece of material flew off and lodged into EE's left index finger.

While tightening the come-a-long, the pad eye broke off striking EE in the right leg, right below the knee. EE did not seek medical attention until 5/7/05.

While replacing middle hanger bearings and shaft, the shaft had to be removed by hammering it loose. While hammering the shaft, a piece of metal came off and lodged into employee's left hand.

EE was putting back a concrete form. He used a prybar to move the form and it slipped from his hand. He subsequently hit his hand on the concrete form.

Another employee was replacing mixer chutes on Mixer #518. Job scope required him to pound a chute bolt out. While pounding the bolt from the chute, the bolt flew out and struck injured employee in lower abdominal area. First aid was performed on the job site.

EMPLOYEE WAS POUNDING CHUTE TO REMOVE OLD CHUTE LINER. PIECES OF DUST AND RUSTY METAL STARTED TO FALL, GETTING INTO HIS RIGHT EYE.

WHEN EE WAS CUTTING FROZEN BEARING ON PULLEY, HAMMERED BEARING, CAUSING A PIECE OF METAL TO LODGE INTO HIS LEFT HAND BETWEEN THUMB AND INDEX FINGER.

WHILE REPAIRING CONVEYOR BELT #2, EMPLOYEE WAS HOLDING SCREW DRIVER ON BOLT FOR CLIP WHILE ANOTHER EMPLOYEE WAS TIGHTENING NUT WITH AIR IMPACT GUN. SCREW DRIVER SLIPPED & END OF BOLT CUT HIS RIGHT THUMB.

WHILE DISASSEMBLING A HOLE HAMMER, THE EMPLOYEE SPLIT THE CYLINDER AND USED A SLEDGE HAMMER TO REMOVE THE OUTSIDE CYLINDER. THE PISTON BROKE WHEN THE EMPLOYEE HIT IT WITH THE SLEDGE HAMMER AN D A PIECE PUNCTURED THE EMPLOYEE'S RIGHT LEG.

WHILE INSTALLING A 2" WATER PIPE TO THE C-12 HEAD PULLEY AND TRANSFER TOWER, THE PIPE WAS TEMPORARILY HELD IN PLACE WITH TIE WIRE UNTIL THE UNISTRUT SUPPORT COULD BE WELDED ONTO THE CONVEYOR. THE WIRE DID NOT HOLD AND THE PIPE FELL ON THE EMPLOYEE'S RIGHT HAND. THE PIPE SHOULD HAVE BEEN CLAMPED DOWN INSTEAD OF USING WIRE.

THE EE WAS ATTEMPTING [TO] FREE A CONVEYOR BELT WHICH GOT STUCK ON THE CHANNEL IRON. AS HE ATTEMPTED TO CUT THE EDGE OF THE CONVEYOR BELT, THE KNIFE SLIPPED & THE MOMENTUM OF THE KNIFE CAUSED A LACERATION TO THE EE'S LEFT ARM [FOREARM].

EMPLOYEE WAS ATTEMPTING TO CLEAN ROCKS FROM THE PRIMARY PLANT FEEDER WITH A HAMMER THE HAMMER STRUCK A ROCK WHICH IN TURN HIT HIM IN THE LEFT SHOULDER

AS THE EMPLOYEE WAS CHANGING THE BLOW BARS ON THE H.S.I. CRUSHER, HE ATTEMPTED TO HIT THE BLOW BAR PINS WITH A HAMMER. EMPLOYEE SWUNG AND ACCIDENTLY HIT SELF ON THE FOREHEAD.

WHILE ATTEMPTING TO REMOVE A ROCK THAR WAS WEDGED AT THE TOP OF THE SCREEN, THE BAR THAT EMPLOYEE WAS USING SLIPPED. EMPLOYEE WAS HIT ON THE LEFT SIDE OF HIS FACE ON THE UPPER CHEEK AREA.

INSTALLING A WHEEL STUD ON EQUIPMENT #1384. THE ELECTRIC PUMP BUTTON GOT STUCK AND EMPLOYEE'S LEFT HAND WAS CAUGHT BETWEEN THE HYDRAULIC RAM AND INNER WHEEL.

EMPLOYEE & HELPER WERE ATTEMPTING TO CHANGE KIHEI PLANT GATE SEAL HELPER WAS PUNCHING OUT PIN WITH A HAMMER MISSED PIN & HIT THE EMPLOYEES THUMB WITH THE HAMMER

EMPL WAS REMVOVING BROKEN BOLTS. AFTER CUTTING BOLT ATTEMPTED TO REMOVE BROKEN PIECE BY POUDING IT OUT. PIECE OF METAL FLEW OUT & STRUCK HAND,

WHILE USING A PRY BAR TO PRY AWAY RUBBER, PRY BAR SLIPPED AND STRUCK EMPLOYEE ON LOWER LIP AND CHEEK.

EMPL USING PRY BAR OPENING SCREEN GATE AND STRAINED BACK.

WHILE EMPLOYEE 4AS HOLDING ONTO CHAIN WHEN CHAIN HOIST DRIVE SIDE HOOK SLIPPED OUT OF HOOKED AREA. SAFETY LATCH ON HOOK WAS BROKEN.

CHANGING GATE U3DER S2 TO C23 HAND SLIPPED AND HIT LEFT HAND ON RAIL.USING A BAR TO TURN GATE.

FRAWCTURE 5TH F3NGER AND ROPE BURN ON R HAND WHILE REMOVING BEND PULLEY FROM CONVEYOR FRAME THE RATCHET HOIST HOOK CAME OUT OF THE CABLE SLING AND A FULL LOAD WAS SUPPORTED BY THE EMP HOLDING THE TAG LINE IN3HIS HAND

EMP WAS ATTEMPTING TO CLEAN CRUSHWER USING A HOIST HIS RIGHT HAND GOT CAUGHT IN THE CABLE SHEAVE RESULTING IN SEVERE LACERATIONS TO HIS RIGHT HAND (5TH FINGER) WITH BROKEN BONES AND CUT T TNEDONS