Esta búsqueda
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
Employee was cutting plastic tie wrap with razor knife; knife slipped and cut employee on left palm of hand.
EE COMPLAINED HIS ARM WAS HURTING AFTER USING HAMMER (5/19/04). ON 6/8/04 EE REQUESTED TO SEE A DOCTOR. THE DOCTOR FOUND NOTHING WRONG. ON 7/1/04 EE WAS REFERRED TO A PHYSICAL THERAPIST. EE WAS GIVEN THERAPY AND TOLD TO AVOID USING A HAMMER ON THE JOB (RESTRICTED USE OF HAMMER, BUT ALLOWED ALL OTHER DUTIES).
EE WAS ATTEMPTING TO CUT OFF THE OUTER JACKET OFA 480 FAN POWER CABLE. EE WAS CUTTING TOWARDS HIS LT. HAND WHEN THE KNIFE SLIPPED AND CUT HIS FINGERS. EE RECEIVED A TOTAL OF 12 STITCHES. HIS RESTRICTIONS DO NOT HINDER HIS ABILITY TO PERFORM HIS NORMAL JOB DUTIES.
EMPLOYEE CONTENDS HE REINJURED HIS LOWER BACK ON 2-13-03 ( NO SPECIFIC INCIDENT BUT WAS SORE AT THE END OF SHIFT) MANAGEMENT WAS NOT AARE OF THE RE-AGGRAVATED INJURY UNTIL 2-7-03. ORIGINAL INJ URY ON 12-29-02, EMPLOYEE WAS SHOVELING AND HIT A BOLT IN THE FLOOR CAUSING HIM TO FEEL A PULL IN HIS LOWER BACK. EE DID NOT SEEK MEDICAL ATTENTION AT THAT TIME.
EE USING SAFETY KNIFE TO TRIM FACE SHIELD TO FIT FACE SHIELD FRAME. MADE CUT TOWARDS SELF, CUT LEFT WRIST. INJURY REQUIRED 5 STITCHES.
EE ATTEMPTING TO CUT TIE-WRAP WITH KNIFE. KNIFE BLADE HIT BED OF VEHICLE ABRUPTLY STOPPING CAUSING EE'S HAND TO HIT KNIFE BLADE, CUTTING FINGER.
EE WAS USING PIPE WRENCH TO CHANGE OUT PIPE ON SPRINKLER SYSTEM. USED UPPER BODY TO ASSIST IN PUSHING ON WRENCH. FRACTURED SEVENTH RIB.
EE USING PUNCH TO REMOVE BOLT FROM SHEAVE WHEEL. SMALL PIECE OF BOLT BROKE OFF AND PENETRATED EE S LEFT LEG AT KNEE.
EMPLOYEE ATTEMPTING TO STRAGHTEN UP PILE OF PALLTS USING SCALING BAR. SCALING BAR SLIPPED CAUSING EMPLOYEE TO FALL.
EMPLOYEE USING SLEDGE HAMMER TO REMOVE PIN. FELT PAIN IN ELBOW.
MECHANIC USING METAL PUNCH TO REMOVE PIN ON UNDER CUTTER CHAIN. POINT OF PUNCH BROKE OFF AND HIT ANOTHER MECHANIC ON CHIN. CAUSING A SMALL CUT ON CHIN ONE STITCHES REQUIRED.
THE EE WAS ASSISTING IN THE REMOVAL OF A 55 GALLON DRUM FROM A PALLET, USING A MANUAL DRUM HOIST/DOLLY. THE DRUM WAS OBSTRUCTED, CAUSING THE SWING ARMS TO MOVE, PINCHING THE EE'S FINGER.
EE ATTEMPTING TO REMOVE U JOINT ON UNDERCUTTER, FAILED TO TAKE RETAINING SPRING OFF. ANOTHER EE USED HAMMER IN ATTEMPT TO REMOVE U JOINT. JAMMER GLANCED OFF AND HIT EE ON FINGER, BREAKING BONE AND INFLICTING BAD CUT.
EE WAS TAPPING A TROUGHING IDLER INTO POSTION WITH A SLEDGE HAMMER. HIS LEFT INDEX FINGER WAS PINCHED BETWEEN THE HANDLE OF THE HAMMER AND THE STEEL CHANNEL OF THE BELT STRUCTURE.
EMPLOYEE USING HAMMER TO INSTALL LINK ON CRUSHER CHAIN, SMALL METAL BROKE OFF OF HAMMER AND LODGED IN ENPLOYEE'S FINGER.
EE WAS LAODING A BULK TRUCK. THE HAND WHINCH USED TO RAISE AND LOWER CHUTE MALFUNCTIONED AND JAMMED EMPLOYEE'S HAND AGAINST HANDLE. ACCIDENT NOT REPORTED UNTIL 7-6-98.
EE WAS HAND SCALING IN THE FACE AREA. WHEN PRYING DOWN SALT WITH THE BAR HE FELT A SHORT PAIN IN HIS WRIST.
EE PULLED MUSCLE IN BACK WHILE SCALING LEDGE OF BENCH IN ROOM T-28.
THE EMPLOYEE ALLEGES HE WAS INJURED WHILE PULLING ON A PIPE WRENCH. IT WAS CONNECTED TO A OPEN WATER VALVE.IT WAS HARD TO TURN.
THE EE WAS BEATING ON A CHUTE FOR OUR ROCK PROJECT HOPPER WITH A 12# SLEDGEHAMMER. HE HIT HIS HAND AGAINST A PROTRUDING BOLT ON HOPPER.