Buscar en el registro

Electrician was stripping wire with a box knife, when the electrician pulled the wire the knife caught pinky finger requiring 3 stitches.

Two employees were removing a pivot shaft seal using a pry bar and a utility knife. While one employee was prying on the seal the other employee was cutting the seal when the pry bar slipped off and struck the employee that was cutting the seal. Employee received three stitches in nose.

Employee was using a Hilti caulking gun to dispense epoxy into loose bolts. Employee failed to puncture the seal on end of tube and pumped pressure into the tube. When nothing came out, employee turned tube to look inside the end, the seal burst shooting epoxy onto safety glasses and into employees eye.

Employee was cutting a zip tie off of an extension cord. The blade of the pocket knife slipped and struck the employee in the left hand. The employee received 6 stitches on left hand.

Employee was using a pocket knife to cut a hole in and vent the bottom of a 1 gallon RV antifreeze bottle used to fill the water system of a blast hole drill. The bottle slipped from his hands, employee tried to catch it and in the process the knife cut his left thumb requiring seven stitches.

Person had is arm and hands between a fusion machine carriage using a crescent wrench. He was using this tool to wrench out the liner to help the liner pipe line up. staff member closed the carriage on his arm. This was caused from miscommunication between the two staff members. Tyrone was checked out a medical facility and had no breaks or cuts. He did have a bruise.

Employee was using a pry bar to dismantle and repair a light duty vehicle drive shaft when he sustained right shoulder pain. Was reported as a minor strain and employee would monitor improvement. Smoky Canyon received notification 12/12/11 from workmans comp that this injury was work related after an investigation was completed.

Employee was removing roller pin with a porta power from the under carriage of a D10 dozer. Pin became wedged,employee was tapping it with a 3lb. hammer. When the pin gave free it hit employee in the thigh bruising it. The next day employee's leg hurt, we sent him to the doctor. Examination showed possible blood clot, employee was admitted into the hospital for observation.

Employee was using a porta power to push a pin out of track frame, the pin slipped and porta power fell on employees right shoulder. There was damage to a tendon and surgery was done on 11/22/2010, first lost day was 11/23/2010.

Employee was removing a track roller off a 3600 Hitachi shovel, it was hung up and employee was prying on it with a pry bar. He felt a burning sensation in his groin area.

Employee was installing a rear gear on the end of a camshaft. He missed the punch with a hammer and hit his hand on stud between the middle and ring finger. He was taken to local medical facility. Hand was soaked in antibiotic liquid, ex-ray taken, and given a tetnus shot. Employee was given prescription for antibiotics and released to full time non restricted work.

EE was using a rubber mallet to remove wet product from a bucket. Felt a strain in the middle of the back.

EE WAS PRYING THE CAP OF AN AEROSOL PAINT CAN WHEN THE SCREWDRIVER SLIPPED & STABBED HIS LEFT HAND.

BEATING DENTS OUT OF BUCKET ON SMALL BACKHOE. SMASHED LITTLE FINGER BETWEEN HAMMER HANDLE & CONCRETE FLOOR.

USING A PRY BAR TO UNPLUG FEED CHUTE. BAR SLIPPED CAUSING EMPLOYEE TO TWIST BACK.

OPENING A CAN OF COFFEE. PULL TAB BROKE OFF OF LID. CONTINUED TO REMOVE LID WITH MULTI-TOOL & IT SLIPPED AND CUT HIS THUMB. HE RECEIVED 4 STITCHES.

WORKING ON TRACK DRILL. 2 EMPLOYEES WERE PULLING ON PIPE WRENCH WHEN THE WRENCH BROKE. ONE EE FELL ON THE OTHER'S KNEES. WENT TO DR. ON 6-11-02. BECAME REPORTABLE 6-17-02.

WHILE CHANGING OUT A SHOVEL BUCKET, EE WAS KNOCKING WEDGE WITH A 12LB HAMMER. THE EE LOST HIS FOOTING CAUSING THE EE TO FALL ON THE HAMMER HANDLE & HIT HIS SAFETY GLASSES SMASHING THE BRIDGE INTO HIS NOSE. THE NOSE CUT REQURIED 5 STITCHES

EE WAS REMOVING ROCKS FROM SCRUBBER WITH A PRYBAR. HE FELT A PAIN IN THE LEFT SIDE OF HIS NECK. THIS LEFT SIDE WENT NUMB DOWN TO HIS WAIST.

WORKING ON 13880, TAKING COVER OFF, TURNING WRENCH. HAND RUBBED AGAISNT A SHARP WELD CUTTING FINGER.

REPLACING SHOVEL TEETH, SWINING SLEDGE HAMMER. DRIVING PIN INTO SHOVEL TOOTH WHEN HAMMER HIT SOLID THEN FLIPPED SIDWAYS-JARRING ELBOW. FINGERS THEN STARTED TO GO NUMB.

LOOSENING BOLTS W/A 3/4" RATCHET AND CHEETER PIPE. PULLING UP ON THE PIPE HANDLE, STRAINED LOWER BACK MUSCLES.

WHILE REMOVING REAR SUSPENSION ON 13710- ELECTRA HAUL, PORTA POWER PRESS SLIPPED AND SMASHED FINGER.

EE WAS CHANGING OIL IN DIFFERENTIAL IN 122100 LOADER, USING CHEATER PIPE ON WRENCH TO REMOVE DRAIN PLUG.

EMPLOYEE WAS CHIPPING SOME WELDING SLAG OFF A WELD, A PIECE OF SLAG GOT BEHIND HIS GLASSES. HE WAS WORKING INA WINDY CONDITION.

PULLING ON A WRENCH AND STRAINED HIS BACK.

EXTENSION FELL OFF A WRENCH HIT THE EMPLOYEE IN THE MOUTH BREAKING A TOOTH

REPLACING TRAVEL BROKE ON A 2300 PH ELEC TRIC SHOVEL MECHANIC WAS REPLACING LEFT LOWER BRAKE PAD WHEN THE PRY BAR SLIPPED & THE LOWER BRAKESHOE BELL ON THE MECHANIC RT HAND RT THUMB & FINGERSS

CUTTING PROTECTIVE WRAPPING FROM A PART.

MUSCLE STRAIN IN LEFT SHOULDER FROM LIFTING TORQUE WRENCH, AND TORQUEING BOLTS.

WORKING ON NO. 2 P.D. PUMP WRENCH SLIPPED HITTING HIM ON RIGHT ELBOW RESULT IN BROKEN RIGHT ELBOW.

WORKING UP THE RAILROAD TRACK CLOSING CAR DOORS. BAR SLIPPED AND HE FELL ON RIGHT WRIST FRACTURED RIGHT WRIST.

EE WAS INSTALLING SCARFIRE TEETH ON A PATROL.

INSTALLING METAL SLING TO LIFT UP SCRUBBER SLING SLIPPED OFF OF HYD JACKS HITTING I ANME WHILE HE WAS STANDING ON LADDER RESULTS BEING KNOCK TO THE CONCRETE FLOOR FRACTURE PELVIS AND L RING FI NGER BROKEN

EMPLOYEE WAS INVOLVED IN ANALTERCATION ABOARD A MINE TRANSPORTATION VEHICLE ON WAY TO THE WORKING SIGHT. ANOTHER EMPLOYEE USED A POCKET KNIFE TO CUT HIS FACE.

FELT PAIN IN LOWER BACK FROM MOPING & SWEEPING

ATTEMPTING TO REMOVE A RIPPER TOOTH, THE BLOW OF A HAMMER SENT A SMALL METAL FRAGMENT INTO LEFT LEG.

CHANGING BUCKET TEETH ON A SHOVEL, A METAL CHIP FLEW AND IMBEDDED ITSELF IN THE LEFT LEG BY THE KNEE.

CLOSING BOTTOM DOOR ON RAIL ROAD CAR WITH BAR BAR SLIPPED SMASHED FINGER BETWEEN CAR AND BAR

PULLING ON A BA9 AS A LEVER FELT DISCOMFORT IN ARM. REPORTED 4 17 87 DID NOT GO TO DR UNTIL 7 17 87 STARTED TO LOSE TIME DUE TO OPERATION N SHOULDER 7 27 87

I NAME WAS CHAN1ING SOME SHOVEL BUCKET TEETH. THE BLOW OF 16 LB SLEDGE HAMMER SHIPPED A FRAGMENT OF METAL OFF THE TEETH.

STRIPPING WIRE 3NSULATION WITH POCKET KNIFE KNIFE SLIPPED CUT FINGER 3 SUTURES

REMOVING SPROCKET FROM PORTA POWER.THE STRIKE OF HAMMER FLAKED METAL CHIP WHICH ENTERED NECK.THE DAY OF THE ACCIDENT,DR DECIDED TO LEAVE METAL IN HIS NECK AND HE ARETURNED THIS WORK.ON 6-28 T HE DECISION WAS REVERSED AND METAL WAS REMOVED.

LOWERING PUMP INTO SUMP PUMPSTOPPED GOING DOWN THEN TIPPED SIDEWAYS PINNING THUMB BETWEEN PUMP AND HAND RAIL

EMPLOYEE LEANING OUT HOLDING WEIGHT AGAINST PLUGGED PIPE, HIT PLASTIC PIPE WITH HAMMER PIPE BROKE EMPLOYEE FELL, PIPE AND ORE LANDED ON EMPLOYEE

HIT FINGER WITH HAMMER

TRYING TO OPEN FROZEN DOOR ON TOPOF RAIL CAR LOCKING BAR TO DOOR FELL ON INSTEP LEFT FOOT.

STRAINED BACK WHILE CHIPPING ICE BENEATH RAILRAOD CAR

PORTA POWER TOOL FELL AND HIT FOOT ABOVE STEEL TOE ON BOOT