Buscar en el registro

IP was prying mill balls out of the finish mill #5 screens when one of the balls shot lose and struck IP in the mouth chipping front tooth.

Alignment hand tool hit injured person in the chin while EE was attempting to free it.

Miner smashed finger with hammer.

IP and other employee where using a chain hoist to pick up an electric motor for the #2 Swing Mill into position for the mobile crane to hoist into proper placement. The IP claims the IP disregarded it in the beginning and finished the job but the days following the pain had increased.

Employee was preparing to setup to transfer cement. When preparing to loosen bolts on the cement line employee had a very sharp pain in left shoulder and bicep. Was seen by Dr on 6/19 & 6/26. Dr reported he had slight tear in left bicep/shoulder. Could continue to work without any restrictions. Employee reported he was still in pain. Returned to Dr and surgery is 11/12.

Employee was changing out the K410 DDC burner gasket. While installing the gasket between the 8" flanges the pry bar slipped and the flange closed together pinching the end of his index finger on his right hand. The end of the finger was cut off and surgery performed later that afternoon. Employee returned to the doctor on Thursday, 11/7 for evaluation. Could be off 2-4 weeks.

Employee was using a come-along when his hand slipped off handle causing him to strain left shoulder. Treated on date of injury and was released to return to full duty with no restrictions or prescriptions. On 05/11/2006 insurance carrier contacted employer about results on MRI with possible surgery.

While sweeping floor on kiln floor, the employee developed lower back pain and muscle spasms.

Employee was closing bottom doors on railcar with a 25 lb bar.

EE WAS ATTEMPTING TO LINE UP A BEAM USING A SLEEVER BAR. HAD CLIMBED UP ON A SAFETY LINE TO TIGHTEN IT UP. THE SLEEVER BAR SLIPPED CAUSING HIM TO LOSE HIS BALANCE & FALL TO THE SURFACE BELOW.

W0RKER TIGHTENING SOME 1" PIPE IN THE PREMILL AREA. WHILE WORKING HE IT HIS LEFT ELBOW ON METAL IN THAT AREA.

EE WAS PULLING GAS ANALYZER PROBE AND STRAINED LOWER BACK.

EMPLOYEE WAS TRYING TO LOOSEN NUT ON CHIPPING HAMMER WITH A PIPE WRENCH. NUT BROKE LOOSE AND CAUGHT HIS RIGHT FINGER IN A PINCH POINT BETWEEN A TABLE AND THE WRENCH. DISLOCATED FINGER, SURGICA LLY PUT IN PLACE.

EE WAS HOLDING COAL MILL ROLL AS A FELLOW EE SWUNG A SLEDGE HAMMER, THE HANDLE BROKE IN MID AIR. THE SLEDGE HAMMER STRUCK THE RIGHT THUMB OF THE INJURED EE-FRACTURED 1ST JOINT.

ANOTHER EE LOST HIS BALANCE PRYING A REDUCER AND FELL INTO EE PUSHING HIM AGAINST HANDRAIL. HEADACHE, STRAIN NECK AND BACK, LEG HURTS.

EMPLOYEE WAS TIGHTENING BOLTS ON CLINKER DRAG CONVEYOR AND AGGRAVATED INJURY OF 2-28-96 OF LOWERBACK.

EE WAS TRYING TO LOOSEN BOLT ON CYLINDER AND PULLED MUSCLE WHILE USING WRENCH ON BOLT.

EMPLOYEE WAS POSITIONING CHAIN FALLS ON TROLLEY BEAM AND FELT PAIN BETWEEN SHOULDERS. CHIROPRACTOR.

EE WAS USING PIPE WRENCH ON AIR HOSE COUPLINGS AND HURT SHOULDER.

EE WAS USING WRENCH TO LOOSEN NUT AND STRAINED UPPER BACK.

EMPLOYEE WAS USING PIPE WRENCH AND CHEATER TO HELP ANOTHER EMPLOYEE UNPLUG VANE FEEDER WHEN THE FEEDER BROKE LOOSE HE FELL TOT HE FLOOR AND PULLED A MUSCLE IN HIS BACK.

EMPLOYEE WAS INSTALLING VIBRATOR ON BOTTOM HOPPER OF RAIL CARS ALSO USING 5FT LONG STEEL BAR TO OPEN DOORS ON RAIL CARS & BAR SLIPPED & SNAPPED BACK STRIKING HIM ON LEFT THIGH

EE WAS USING BRUSH HOG TO MOW WEEDS WHEN A ROCK WAS THROWN INTO HIS LEFT CHEEK CAUSING A CONTUSION. EE ALSO DEVELOPED BRONCHITIS AND RHINITIS FROM BREATHING DUST WHILE MOWING WEEKS.

EMPLOYEE WAS USING PIPE WRENCH TO TIGHTEN PIPE UNION ON A WATER LINE & PULLED MUSCLE IN MIDDLE BACK

EMPLOYEE WAS USING LONG ROD TO UNPLUG MATERIAL INSIDE CONE OF PREHEATER. HE TWISTED HIS SHOULDER AND STRAINED HIS UPPER BACK.

EMPLOYEE WAS USING HAMMER TO POSITION CEMENT FORM ANCHOR. HAMMER SLIPPED OFF ANGLE IRON AND CUT FIRST FINGER OF LEFT HAND REQUIRING SUTURES.

EMPLOYEE WAS SHOOTING 8 GAUGE SHOT GUN SLUGS INTO KILM TO REMOVE BRICK WHEN A PIECE OF SLUG WENT THROUGH A SMALL OPENING IN THE SHIELD & STRUCK EMPLOYEE ON RIGHT CHEEK.

EMPLOYEE WAS HOLDING SEAL IN VALVE WHILE ANOTHER EMPLOYEE TIGHTENED NUT, CAUGHT THUMB IN PINCH POINT BETWEEN NUT AND PIPE, CONTUSION LEFT THUMB.

EMPLOYEE PULLED ON CHAIN OF CHAIN FALLS AND STRAINED BACK AND NECK.

EMPLYEE WAS TAKING A 2" UNION OFF OF AIR LINE WHEN OTHER END OF PIPE WHICH HAD A 2" VALVE ON IT UNSCREWED FROM PRESSURE SIDE OF THE CLOSED VALUE. PIPE BLEW OFF AND HIT EMPLOYEE ON LEFT FOOT. EMPLOYEE DID NOT HAVE WRENCH ON VALVE TO KEEP IT FROM LOOSENING.

EMPLOYEE CUT HER THUMB AS SHE WAS CLOSING BLADE ON UTILITY KNIFE. SUTURES REQUIRED.

EMPLOYEE PULLED ON CHAIN FALL AND STRAINED BACK.

TIGHTENING MOTOR BASE BOLTS IN AWKWARD POSITION AND STRAINED UPPER BACK.

54736YEE WAS CUTTING AIR HOSE WHEN HIS KNIFE SLIPPED LACERATION RIGHT THIGH.

54730TRYING TO UNPLUG FEED PIPE OF LODGED MATERIAL INSIDE AND THE HOT MATERIAL BLEW OUT HOLE AND BURNED EMPL RIGHT EAR,RIGHT SIDE OF FACE & NECK

PULLED TOO HARD ON WRENCH STRAINED RIB MUSCLE

EMPL RUNNING CHAIN ON CHAIN FALLS TO HOIST MOTOR AND HURT BACK. CO BELIEVES THIS AGGRAVATED PREVIOUS INJURY OF 6-24-92 COPY ATTACHED.

EMPLOYEE PULLED ON 4' BAR OPENING BOTTOM GATE ON HOPPER CAR. PULLED MUSCLE IN RIB CAGE.

EMPLOYEE WAS TIGHTENING CLINKER COOLER GRATE BOLTS AND STRAINED NECK AND SHOULDER MUSCLES.FIRST TREATMENT05-15-92.

EMPLOYEE WAS REACHING OUT TO MEASURE FOR CONDUIT AND HURT HIS BACK.

EMPLOYEE WAS CUTTING REINFORCING WIRE OUT OF A HOSE WHEN KNIFE SLIPPED.CUT LEFT INDEX FINGER.

PIECE OF SHOTGUN SHELL SLUG OR COATING OF KILN RICHOCHETED AND HIT EMPLOYEE ON ARM.

EMPLOYEE WAS MEASURING SILOS WITH A ROPE WHICH SLIPPED OUT OF HIS HANDS HE GRABBED FOR THE ROPE WITH HIS RT HAND & HIT THE MEASURING P ORT & BROKE RT LITTLE FINGER

EMPLOYEE WAS LOOSENING BOLT AND FELT PAIN BETWEEN SHOULDERS.

WRENCH SLIPPED AND HIT EMPLOYEE IN FACE. POSSIBLE TOOTH WAS KNOCKED LOOSE.

EMPLOYEE WAS CLEANING IN PREHEATER AREA AND GOT DIRT INTO HIS EYE.

EMPLOYEE WAS OPENING RAIL HOPPER CAR WITH BAR THE BAR STUCK & THEN RELEASED SUDDENLY HE FELT PAIN IN UPPER LEFT ARM & SHOULDER

PULLED ON CHAIN OF HOIST AND HURT BACK.FIRST TREATMENT 6-12-91.

WHILE EMPLOYEE WAS UNPLUGGING CHUTE, HIS KNUCKLE GOT CUT WHEN HE HIT A PIPE.

EMPLOYEE WAS SWINGING SLEDGE HAMMER AND STRAINED BACK.