Buscar en el registro

Employee was cutting a piece of metal with an electric grinder when the cutting disk bound up causing the grinder to kick back and cut the top of their hand.

Individual was attempting to loosen a screw conveyor, while going through equipment checkout. procedure was to pull towards them with the pipe wrench. The screw would not loosen, subject attempted to move it in the opposite direction. The pipe wrench slipped off and individual fell forward injuring his arm with a minor laceration.

Employee fractured tip of left thumb, struck with hammer

While loosening a bolt, the wrench slipped and employee cut/bruised back of right hand

While cutting banding from a pallet of bags using a utility knife, the worker slipped and cut his left index finger.

While loosening a bolt using a breaker bar employee felt pain in his lower left rib. The pain continued and he sought medical assessment and received a work restriction of "light duty-limited lifting".

Employee was on the 1st floor PX 7000D mill. He was on a boom lift replacing the structural bolts by using a torque wrench to tighten them up. When he was tightening the first bolt the wrench fell off the bolt while he was pushing down causing his hand to be in the middle of the concrete block and the wrench.

Cut palm of left hand with utility knife while trying to cut rope.

Strained right elbow while shovelling wet product

Employee was swinging a hammer to loosen material & struck a flange with his hand, resulting in a pinch/laceration requiring sutures.

Employee and one other were using a bar to lift a ~150lb object. Felt pain in his back 3 days later & then went to a chiropractor on his own.

Employee was cutting a hose from Darbed fitting water running down everything. Knife slipped & employee lacerated the palm of left hand. 4 stitches required.

EE WAS DISMANTLING COWLES MIXER BLADE FROM A SHAFT. EE WAS USING A WRENCH AND SOCKET WITH RATCHET THAT WERE NOT THE CORRECT SIZE FOR THE JOB. THE BOLT CAME LOOSE, EE'S HAND SLIPPED AND HIT THE BLADE.

While employee was standing on a piece of dewatering equipment trying to free a bound rotating assembly with a bar, the bar slipped and employee lost his balance, fell and broke a bone in his leg.

CUT HAND WITH KNIFE WHILE CUTTING BULK BAG CONTAINING WASTE PRODUCT.

EE WAS CUTTING A BAND ON A CARTON OF PAPER. WHEN BAND BROKE, KNIFE SLIPPED AND STRUCK OTHER ARM.

EE WAS TIGHTENING FLANGE AND CUT HAND ON SHARP OBJECT.

HE WAS INSTALLING IMPELLER ON 3K WILLFLEY PUMP & WRENCH SLIPPED & HIS HAND HIT THREADED ROD ON PUMP Y

EE WAS MOVING A METAL CHUTE AND THE CHUTE POPPEDFREE & COMEALONG HIT EE IN THE FACE. EE RECD A BROKEN NOSE & 2 BLACK EYES

EMPLOYEE WAS CUTTING IN BAGS TO BRING BUL BAGGER UP OT CORRECT WEIGHT. EMPLOYEE CUT HIMSELF WITH A UTILITY KNIFE.

DURING THE REMOVAL OF TOP HATCH BOLTS ON A RR CAR, A BOLT WAS TOO TIGHT TO REMOVE BY HAND, EE THEN KICKED THE WRENCH WITH HIS FOOT, TRYING TO LOOSEN THE BOLT. A GLANCING BLOW RESULTED, BRUISIN G HIS HEEL. THE DR CALLED THE INJURY A FOOT HEEL CONTUSION. AFTER AN INJURY INVESTIGATION, IT WAS IDENTIFIED AN AIR ... MUST BE USED TO REMOVE THE BOLTS.

UPON FINAL FOLLOW UP, EE INFORMED ME THAT HE HAD STICHES IN THE TIP OF HIS FINGER WHICH HE CUT TWITHA DULL UTILITY KNIFE BLADE. HE WAS HACKING AT A PIECE OF PLASTIC STRIP WHEN HIS HAND SLIPPED .

SPLITTED L.S. STRAIN OF LEFT LITTLE FINGER.

EMPS WERE WORKING/HAMMERING ON A METAL SHAFT. METAL WAS BRITTLE AND A PIECE BROKE OFF AND EMBEDDED IN EMPS FOREHEAD.

TIGHTENING BAG SPOOL W/ALLEN WRENCH AND THUMB POOPPED OUTOF JOINT.

EMPLOYEE WAS TRYING TO FREE UP A 45B DISCHARGE PUMP USING A PIEP WRENCH AND PIPE EXTENTION.

EMPLOYEE WAS REMOVING INSIDE ROLLER BEARING RACE FROM SHAFT, TAPPING ON IT WITH A HAMMER, SMALL PIECE OF BEARING CHIPPED OFF AND STUCK INTO INSIDE OF LEFT LEG.

THE EMPLOYEE WAS UNPLUGGING THE CENTRIFUGE, CONSISTING OF TURNING THE LOCKED UP SCREWS BY HAND WITH A PIPE WRENCH UNTIL FREE. EE SAYS THIS TOOK FROM 3:30 PM UNITIL 6 PM CONTINUOUSLY, AS HE COU LD STOP ONCE STARTED OR THE SLURRY IN THE SCREW WOULD HARDEN AGAIN.

EMPLOYEE WAS REPAIRING LOADING DOCK LEVELER. RATCHET ARM WAS SPRING LOADE. EMPLOYEE RELEASED RATCHED ARM WHICH SPRUNG BACK AND INJURED HIS RIGHT THUMB.

EMPL RIPPING NAILS OUT OF A BOARD.SWUNG THE HAMMER CLAWS DOWN,OVEREXTENDED AND HIT HAND.

HE WAS HAMMERING A CYCLONE WHEN HIS RIGHT INDEX FINGER STRUCK A PROTRUDING TOOTH.

CUTITNG MEWAL WITH TIN SNIPS WHILE CUTTING THE TRACK HAND SLIPPED HE SLICED THE OUTSIDE OF HIS RIGHT THUMB HE ALSO PARTIALLY CUT A TENDON

EMPL WAS FREEING UP PUSHER BAR ON PALLETIZER. ONCE FREED PUSHER BAR MOVED BACK & PINCHED FINGER & BROKE FINGER.

EMPL CUTTING BOXES WITH RAZOR KNIFE CUTTING INCORRECTLY BY PULLING KNIFE TOWARDS HIS BODY.KNIFE SLIPPED AND CONTINUED ON INTO EMPL LEG.HIS LEG WAS CUT REQ 4 STITCHES.

EMPLOYEE WAS IN8TALLING A VALVE ON A GEAR BOX FOR AN OIL DRAIN. EMPLOYEE WAS TIGHTENING THE VALVE WITH A PIPEWRENCH AND EXPERIENCED A PAIN IN HIS BACK.

EMPLOYEE WAS WO9KING ON A VALVE & HIT AN ALLEN WRENCH WITH A HAMMER TO TURN A BOLT THE HAMMER BOUNCED BACK SHARPLY EMPLOYEE SUSTGAINED A TWISTED WRIST