Buscar en el registro

EE WAS TIGHTENING A BOLT WITH AN END WRENCH WHEN HE FELT PAIN IN HIS BACK. EE WENT TO A CHIROPRACTOR FOR HIS CONTINUED BACK DISCOMFORT ON 3/26/97.

EE WAS PRYING ON A ROD IN THE ROD MILL, WHEN THE ROD SHIFTED SMASHING THE TIP OF HIS LITTLE FINGER ON HIS LEFT HAND.

EE WAS INSTALLING BALL MILL DRYING ON A LINER WITH A 5' BAR, THE BAR BROKE HITTING EE IN THE LEFT SHOULDER.

EMPLOYEE WAS POUNDING PIN INTO BOOM OF WELDING TRUCK AND FELT PAIN IN BACK.

EMPLOYEE WAS PRYING CHUNKS FROM CHUTE, EXPERIENCED PAIN IN LOWER STOMACH.

WHILE REMOVING A COUPLING HUB FROM A DRIVE MOTORTHE EMP STRUCK THE HUB TO HELP START IT MOVING, CAUSING A SLIVER OF STEEL TO FLY OFF AND BECOME IMBEDDED IN HIS RIGHT EYE.

THE INJURED WAS ADJUSTING THE COBBLER DRIVE USING A FIVE FOOT BAR TO ADJUST THE MOTOR. THE BAR SLIPPED AND PINCHED THE EMPLOYEE'S THUMB BETWEEN THE MOTOR AND BAR.

EMPLOYEE WAS PRYING ON TIRE RIM COMPONENT WHEN PRY BAR SLIPPED FROM HAND AND STRUCK EMPLOYEE ON LEFT FOOT BEHIND STEEL TOE.

EMPLOYEE WAS SEATED ON BOX, BENT OVER, USING A CHIPPING HAMMER TO CLEAN RINGS. WHEN HE STOOD UP FELT PAIN IN BACK. EMPLOYEE WAS COUNSELED BY SUPERVISOR PRIOR TO INJURY ABOUT HIS POSITION.

EMPOYEE WAS PULLING ON END WRENCH WHEN HIS BACK BECAME SORE

EE WAS ATTEMPTING TO REMOVE BEARING HALF WITH A HAMMER WHEN A CHIP FROM THE BEARING FLEW UP AND STRUCK EE IN RIGHT CHEEK. 2 SUTURES.

EMPLOYEE WAS REMOVING DISCHARGE LINE FROM PUMP WHEN WRENCH SLIPPED & EMPLOYEE STRUCK RT FOREARM ON MANUAL VALVE IN AREA

EE WAS POUNDING ON DRIVE SPROCKER SESMENUES ON D-9 CAR DOZER IN ATTEMPT TO LOOSEN THEM FOR REPLACEMENT CHIP OF STEEL FLEW UP FROM SEGAMENT AND STRUCK EE ON INSIDE OF RIGHT UPPER ARM.

EMPLOYEE WAS IN PROCESS OF CUTTING CONVEYOR BELT WITH KNIFE IN CONVEYOR BELT REPAIR SHOP. AS HE PULLED KNIFE TOWARD HIM, KNIFE SLIPPED AND CAUSED PUNCTURE WOUND TO RIGHT UPPER LEG.

EMPLOYEE WAS ATTEMPTING FREE STUCK CHUNKS, WHEN STANDING ON CHUNK, CHUNK BROKE IN HALF AND HOT DUST WENT UP LEFT PANT LEG.

EE WAS POUNDING WEDGE WITH SLEDGE HAMMER, WHILE POUNDING STRUCK LONG FINGER RIGHT WITH SLEDGE HAMMER.

EMPLOYEE WAS CHANGING FILTER SECTOR WHEN RATCHET SLIPED. EMPLOYEE STRUCK 3RD FINGER LEFT ON ADJACENT FILTER SECTOR.

EMPLOYEE WAS ATTEMPTING TO REMOVE DIFFERENTIAL BOLTS WHEN HE EXPERIENCED SPRAIN/STRAIN TO RIGHT CHEST AREA.

INJURED AND PARTNER WERE INSTALLING A SPRING WHEN PARTNER DROPPED HIS 4 POUND HAMMER HAMMER HANDLE STRUCK INJURED BRUISING LEFT ELBOW. NONFIED OF MEDICAL TREATMENT ON 2-28-94.

EE WAS IN THE PROCESS OF CHANGING BUCKET TEETH ON A 12 YD. LOADER--WHILE USING SLEDGE HAMMER TO POUND OUT WEDGES, CHIP OF STEEL FLEW UP AND STRUCK EE ON FOREHEAD.

EMPLOYEE WAS ATTEMPTING TO CUT VACUMN CLEANER HOSE WITH IHS POCEKT KNIFE. WHENKNIFE SLIPPED CAUSING LACERATION REQUIRING SUTURE TO RIGHT HAND.

EMPLOYEE WAS PUSHING DOWN ON 5' BAR IN ORDER TO REMOVE LINER WHEN HE EXPERIENCED PAIN IN RIGHT ARM.

EMPLOYEE WAS IN THE PROCESS OF REMOVING BRAKE BOLTS WITH A THREE QUARTER INCH RATCHET WHEN HE EXPERIENCED PAIN IN RIGHT ELBOW AND LOW BACK.

EMPLOYEE WAS REMOIVNG PUMP PACKING WITH PACKING REMOVAL TOOL WHEN TOOL BROKE. EMPLOYEE FELL BACKWARDS LANDING ON BACK.

SUPERVISE WAS ATTEMPTING TO OPEN CARDBOARD BOX WITH PICKET KNIFE WHEN KNIFE SLIPPED, LACERATING LEFT WRIST.

EMPLOYEE WAS IN PROCESS OF RLEMOVING THICKNER DRIVE BOLTS WITH WRENCH WHEN HE EXPERIENCED PAIN IN BACK.

HE WAS USING THE HYDRAULIC WRENCH TO TIGHTEN THE SECONDARY BOWL. WHEN HE LIFTED WRENCH INTO PLACE HE FELT PAIN IN HIS BACK.

85061S INSTALLING A CLAMP ON 18 LENGTH OF PIPE HE REACHED AROUND THE PIPE TO GRAB THE CRAMP AND FELT PAIN IN HIS BACK.

85061S PEENING A WELD AND GOT A PIECE OF SLAG IN HIS LEFT EYE.

HE WAS REMOVING A PIPE COUPLING WITH A 24" PIPE WRENCH. WHEN PULLING ON THE WRENCH HE FELT PAIN IN HIS BACK.

57759IENCED PAIN DURING AND AFTER REQUIRED DUTIES USING TOOLS. LAST DAY WORKED 05-17-92.

FITTINGS WERE SO TIGHT SO HE GOT INTO THE AREA TO APPLY PRESSURE TO HIS WRENCH HE FORCED PC OF SCRAP METAL THRU HIS FOOT

HE WAS CUTTING PLASTIC TY-RAPS TO REMOVE A TEMPORARILY WATER HOSE TO THE STEAM-JENNY. THE KNIFE SLIPPED AND CUT THE TOP OF HIS LEFT HAND.

HE WAS PUTTING A 50 TON HYDRAULIC RAM UNDER CHUTE INSERT WHILE STANDING ON LADDER HE FELT PAIN ON LEFT SIDE LOWER BACK.

HE WAS INSTALLING A LOWER TUBE ON MULTI TUBES WEST SIDE OF #2 GRATE WHEN THE CHAIN THAT WAS HOLDING THE TUBE SLIPPED PINCHING HIS MIDDLE FINGER ON HIS LEFT HAND BETWEEN THE CHAIN AND THE TUBE.

HE WAS STRIPPING METAL SHIELD FROM CABLE CONDUCTOR. KNIFE SLIPPED AND CUT HIS LEFT MIDDLE FINGER.

HE WAS REMOVING A 6 INCH ELBOW WHILE WORKING ON THE 2A VENTURI SPRAYS ON THE EAST SIDE OF 2 GRATE HIS RIGHT HAND WAS PINCHED WHILE WORKING IN A CONGESRED AREA.

HE WAS REMOVING 60" CRUSHER SPIDER NUTS WHEN THE WHOLE BOLT CAME FREE AND STRUCK HIM ON HIS LEFT THIGH.

HE WAS REMOVING STEERING CLUTCH FLANGE ON D-9 CAT DOZER WITH A PULLER. HE REACHED DOWN TO INSTALL THE DULLER & INJURED HIS LEFT SHOULDER.

HE WAS TIGHTENING BOLTS ON A PUMP CASE. WHEN HE PULLED ON THE WRENCH, HE FELT PAIN IN HIS GROIN AREA. REQUIRES SURGERY.

HE WAS USING A PRY BAR. AN OBJECT STRUCK HIM IN THE LEFT LEG CAUSING A SMALL PUNCTURE.

POSITIONING GRADER CUTTING EDGE WITH BAR,

HE WAS MOPPING FLOOR IN THE HOURLY DRY. HE FELT PAIN IN HIS BACK. RECURRENCE OF AN OLD INJURY. INJURY WAS REPORTED ON 10-19-90.

HE WAS ASSEMBLE GRH CHAIN HE HIT HIS LEFT HAND WITH A SLEDGE HAMMER WHEN LINING UP CHAIN LINKS.

REMOVING NUTS ON CRUSHER DROPPED NUT ON SM TOE R FOOT

HE WAS REMOVING NUTS ON BASE BOLTS OF CRUSHER WITH SLEDGE HAMMER & SLUG WRENCH WHILE SWINGING HAMMER HE FELT PAIN IN HIS BACK

HE WAS HELPING TO GUIDE A LENGTH OF 8" PIPE INTO THE HACKSAW VICE. HIS RIGHT HAND WAS OVER THE END OF THE PIPE. HIS SMALL FINGER ON HIS RIGHT HAND WAS CAUGHT BETWEEN THE VICE JAW AND PIPE.

HE WAS HELPING TO CHARGE ROD MILL. HE WAS USING A BAR TO MOVE RODS IN PLACE, SO MECHANIC COULD PUT ROD INTO MILL. A ROD WAS SUPPOSE TO DROP INTO THE CARRAGE, BUT GOT STUCK, HE DIDN'T SEE THA T IT WAS STUCK AND HE STARTED TO BAR ANOTHER ROD INTO POSITION.

HE WAS PRYING LIFTER BARS AWAY FROM THE WALL OF BALL MILL WITH A BAR.

CUTTING RUBBER HOSE WITH KNIFE KNIFE SLIPPED CUT R KNEE Y Y