Buscar en el registro

THE ELECTRICAIN WAS USING A HACKSAW TO CUT AN ALUMINUM LUG THAT WAS HELD BY A VISE. WHEN THE SAW BLADE CUT THROUGH, THE EMPLOYEE;S FINGER STRUCK THE EDGE OF THE LUG. IT TOOK 2 SUTURES TO CLOSE THE WOUND.

THE EE SLICKER PANTS WERE TORN AT THE BOTTOM. THE EE DECIDED TO CUT OFF A LOOSE PIECE SO WOULD NOT TRIP ON IT. USING A BOX CUTTER TYPE KNIFE, HE PROCEEDED TO DO SO AND SLICED THE HAND HOLDING THE PANT LEG. HE RECEIVED 3 SUTURES INT HE CUT, AND WAS RELEASED TO FULL DUTY THAT DAY.

WORKER WAS FABRICATING A METAL HOOK WHEN PLIERS SLIPPED AND METAL ROD LACERATED LEFT HAND BETWEEN THUMB AND INDEX FINGER. INJURY REQUIRED SEVEN STITCHES.

WHILE REPAIRING A HYDRAULIC CYLINDAR WITH A SPANNER WRENCH, THE WRENCH SLIPPED AND HE SMASHED THE END OF HIS LEFT MIDDLE FINGER CAUSING A FRACTURE ON THE TIP.

THE EE WAS USING BOLT CUTTERS TO CUT A PIECE OF CHAIN FROM AN AWKWARD POSITION. HE BRACED ONE HANDLE OF THE BOLT CUTTERS AGAINST HIS CHEST AND PULLED THE OTHER HANDLE TOWARDS HIM. HE FELT A "P OP" IN HIS CHEST AREA. THE DR. DIAGNOSED A SOFT TISSUE INJURY IN HIS CHEST AREA AND PLACED HIM ON RESTRICTED DUTY WITH A FOLLOWUP APPT. ON 6-1-01.

THIS MECHANIC WAS REPAIRING A MANTLE FOR A CONE CRUSHER A PAD EYE WAS WELDED TO THE MANTLE & A T3 TON CHAIN COMEALONG WAS ATTACHED & PRESSURE APPLIED TO LOOSED THE 5G NUT HOLDING THE MANTLE TOGETHER. THE WELD ON THE PAD EYE BROKE THE COMEALONG WHICH THE MECHANIC WAS OPERATING HIT HIS RT SHOULDER. THE INJURY RESULTED IN A AC SEPARATION THAT REQUIRED SURGERY. A SAFER METHOD USING

WHILE WORKING ON A CAT 789 HAUL TRUCK, LOOSENING A BOLT. THE WRENCH SLIPPED AND RIGHT RING FINGER WAS CUT ON THE HEAD OF ANOTHER BOLT. HIS KNUCKLE WAS CUT AND REQUIRED 4 SUTURES.

WHILE DOING SOME CLEANUP WITH A SHOVEL, HE STEPPED DOWN ON THE SHOVEL TO PUSH IT FURTHER INTO THE MUD. THE SHOVEL GLANCED OFF OF A BOLT IN THE MUD CAUSING HIM PAIN IN THE LEFT CALF MUSCLE. HE WAS PLACED IN A BOOT CAST UNTIL RECOVERY.

OTHER EE WERE ALIGNING HOLES FOR A PAIN, USING A 6 FOOT PRY-BAR AGAINST SPRING PRESSURE ON THE ROCK BREAKER. THE BAR TIP SHIFTED AND SLIPPED. EE'S FALL WEIGHT UPON THE BAR'S RELEASE, APPARENTL Y SPAINED AND SUBSEQUENTLY BROKE HIS RIGHT ANKLE

THE CREW WAS LIFTING THE END OF THE MOTOR WITH THE WINCH LINE ON THE RIG SO THAT THE LIFTING CLAMP COULD BE ATTACHED THE MOTOR WAS IN A METAL SHIPPING BOX. EMPLOYEE WAS PLACING A BLOCK UNDER THE MOTOR WHEN THE WINCH LINE SLIPPED, PINCHING AND SMASHING EMPLOYEE'S WRIST AND FINGERS. THE WINCH LINE WAS THEN RE-ATTACHED AND THE MOTOR RE-LIFTED TO RELEASE EMPLOYEE'S HAND. ELASPED TIM

EMPLOYEE WAS ATTEMPTING TO LOOSEN A BOLT WITH A WRENCH. HE HIT THE WRENCH WITH THE PALM OF HIS HAND. THIS ACTION HYPEREXTENDED HIS WRIST, CAUSING PAIN IN IT. X-RAYS REVEALED NO FRACTURES, HOWE VER, DUE TO POINT TENDERNESS AND PAIN, THE DOCTOR SPLINTED HIS RIGHT WRIST.

EE WAS ATTEMPTING TO REMOVE A PLASTIC WIRE TIE WITH HIS POCKET KNIFE WHEN HE SLIPPED AND CUT HIS LEFT HAND BY THE INDEX KNUCKLE 2 CM LACERATION. REQUIRED SUTURES TO CLOSE.

EE WAS REMOVING A BROKEN STRIKER BAR FROM THE AIRTRACK DRILL. HE WAS TAPPING THE HAMMER NUT, A PIECE OF METAL FLEW OFF AND EMBEDDED IN HIS RT FOREARM. THE WOUND WAS CLEANED,METAL REMOVED AND S UTUED BY THE DR. INJURY DID NOT RESULT IN WORK IMPAIRMENT.

EE WAS REPAIRING GUARDRAIL WHEN HIS RT LITTLE FINGER BECAME CAUGHT BETWEEN THE HAMMER AND RAIL RESULTING IN THE LOSS OF HIS FINGERNAIL.

HE WAS ATTEMPTING TO CUT A 2" SUCTION HOSE WITH A POCKET KNIFE. THE KNIFE SLIPPED AND HE CUT HIS LEFT MIDDLE FINGER.

TIGHTENING BOLTS ON A RADIATOR WITH RATCHET WHEN IT SLIPPED OFF THE BOLT STRIKING HER ON THE R. SIDE OF HER NOSE.

WHILE DRIVING A SMALL 1/2 MOON BUSHING IN FOR ANIDLER CAB (D9N DOZER) A CHIP OF METAL CAME OFF THE EDGE OF THE HAMMER AND STRUCK THE RIGHT SIDEOF THE FACE, INBEDDING THE METAL CHIP IN THE CHE EK.

2 EE'S WERE CHANGING A 75 LB MOVEABLE HANGING WEAR PLATE ON A PORTABLE CONVEYOR FEED CHUTED. 1 EE WAS ATTEMPTING TO BEND THE PLATE HANGER WITH A HAMMER, WHEN IT BOUNCED AND FELL, HITTING THE R T THUMB OF OTHER EE. THIS CAUSED A LACERATION ON HIS THUMB OF ABOUT 2CM LONG, WHICH REQUIRED SUTURES. X-RAYS INDICATED NO FRACTURES.

A MINOR NON-REPORTABLE CUT BECAME INFECTED 6 DAYS AFTER THE INCIDENT AND HAD TO BE DRAINED BY THE DOCTOR. THE INITIAL CUT ON THE KNUCKLE CAME FROM A METAL BAND THE EMPLOYEE WAS CUTTING.

FINGER WAS PINCHED UNDER PRYBAR WHILE CLEARING FEEDERS IN THE MILL.

WHILE HITTING A CHISEL WITH A HAMMER, A SMALL PIECE OF METAL CAME OFF THE HAMMER STRIKING HIS CHEEK. THE DR. DECIDED TO CUT OPEN HIS CHEEK TO LOOK FOR THE METAL. HE DID NOT FIND ANY HOWEVER HE PUT A SUTURE IN THE INCISION HE HAD MADE LOOKING FOR THE METAL.

WHILE CUTTING A PIECE OF WOOD THE KNIFE SLIPPED AND CUT HIS LEFT INDEX FINGER.

EMPLOYEE WAS BREAKING QUILL ROD WITH CHEATER PIPE AND DEVELOPED BACK PAIN.

EE HIT HIS LEFT HAND WITH A HAMMER WHILE CHISELING OUT A NIPPLE THAT WAS RUSTED INTO A FITTING.

WRENCH SLIPPED FORWARD WHILE TIGHTENING A BOLT CAUSING RIGHT ELBOW TO STRAIGHTEN.

WHILE INSTALLING A TOOTH ON A BUCKET OF A 992 LOADER, HE HIT THE END OF THE TOOTH WITH A HAMMER CAUSING A CHIP TO BUST OFF THE TOOTH. THE CHIP HIT THE BACK OF HIS LEFT HAND CUTTING IT. THE H AND WAS SUTURES.

EE WAS WIGGLING A CHEATER BAR ON A CHAIN BINDER TO REMOVE IT. WHEN THE BAR, WHICH WAS UNHOOKED, POPPED UP UNDER PRESSURE.

EMPLOYEE WAS WORKING IN THE MILL TORQUING BOLTS ON A DOUBLE DECK SCREEN WITH A 600 LB TORQUE WRENCH. EMPLOYEE WAS STANDING BETWEEN TWO SUPPORT BEAMS HOLDING ONE SUPPORT BEAM WITH ONE HAND WHIL E PULLING ON THE WRENCH WITH THE OTHER WHILE PULLING ON THE WRENCH HE FELT PAIN BETWEEN HIS SHOULDER BLADES.

WHILE DRIVING OUT A PIN WITH A HAMMER, A PIECE OF METAL DISLODGED & WENT INTO THE LEG ABOVE THE KNEE ABOUT 2". THE PIECE WAS ABOUT 1/4" X 1/4" &EMBEDDED IN THE LEG ABOUT 1" UNDER THE SKIN.

EMPLOYEE WAS WORKIGN INT EH REFINERY MOVING A GOLD BAR FROM MOUCO TO THE COOLING TUB WITH LIFTING TONGS. WHILE MOVIN GHTE BAR SLIPPED FROM THE TONGS IN THE LOOKING TUB. WHEN THE EMPLOYEE RE- POSITIONED THE TONGS AND LIFTED THE BAR HE FELT PAIN IN HIS BACK.

WHILE STRIPPING A GASKET WITH A POCKET KNIFE THEKNIFE SLIPPED CUTTING THE LEFT INDEX FINGER AT THE SECOND KNUCKLE.

EE WAS REMOVING A BREAK CALLIPER WHICH HAD BEEN LOOSENED WITH A COME A LONG WHILE WRAPPING A CHAIN AROUND THE CALLIPER IT FELL AND HIS CLEVIS CAUGHT HIS FINGER.

EE WAS CUTTING DRIP LINE WITH A RZAOR KNIFE. THE KNIFE SLIPPED AND LACERATED HIS INDEX FINGER.

EE WAS CUTTING A RUBBER LINER WITH A POCKET KNIFE. THE KNIFE HAD A LOCKING BLADE BUT THE BLADE LOCK WAS NOT WORKING THE BLADE FOLDED OVER ONTO HIS INDEX FINGER.

WHILE DRIVING A PIPE INTO POSITION WITH A HAMMER, SHE MOVED HER HAN ONTO THE END OF THE PIPE AND THE HAMMER HIT HER FINGER.

WHILE CLEANIGN DISCHARGE CHUTE IN SECONDARY CRUSHER PINCHED FINGER BETWEENT HE END OF A SHOVEL AND THE DOOR TO THE CHUTE. REPORTABLE AS SUTURES WERE REQUIRED.

WHILE ASSISTING WITH THE REMOVAL OF A CLAMPING BAR THE EMPLOYEE WAS HIT ON THE TIP OF THE LEFT 4TH FINGER. LEFT 4TH FINGER REQUIRED REMOVAL OF THE FINGERNAIL AND ONE STITCHES.

EE WAS CUTTING A STENCIL WITH RAZOR KNIFE HE PUT HIS HANDS TOGETHER & LACERATED THE BACK OF HIS HAND

MAN WAS REPLACING SKIRTING AND WHILE HITTING THE SKIRTING WITH HIS SHOVEL HE STRUCK HIS HAND ON A PIECE OF METAL.

EMPLOYEE WAS DRIVING PIN FROM UNDERCARRAGE OF HAUL TRUCK. DIRT FELL INTO LEFT EYE.

THE CREW WAS INSTALLING NEW LEACH PAD LINER, INJURED WAS USING A KNIFE WITH A HOOK BLADE TO CUT A CIRCULAR PATCH FROM A PIECE OF HOPE PLASTIC. THE BLADE SLIPPED FROM THE PLASTIC & CUT INTO HIS LEFT INDEX FINGER.

WHILE DRIVING A PIN ON A D9 DOZER WIT H A 16 # HAMMER A S TEEL CHIP FLAKED OFF THE PIN STRIKING EE ON THE LEFT SIDE OF HIS FACE JUST ABOVE HIS CHEEK MSHA ;REPORTABLE AS SUTURES WAS REQUIRED

WAS WORKING A BOLT OFF A LOADER WHEN THE BOLT BROKE LOOSE, SMASHING HIS LITTLE FINGER BETWEEN THE WRENCH AND THE LOADER.

EMPLOYEE WAS REBUILDING A BUCKET AND BENDING A STEEL PLATE WITH HEAT AND A COME-A-LONG. THE COME-A-LONG SLIPPED AND THE STEEL FLIPPED UP AND HIT HIM IN THE JAW.

INSTALLING A VICE COUPLING & HIT HIMSELF WITH A HAMMER

TIGHTENING A NUT WITH A WRENCH,IT SLIPPED AND EMPL HAND HIT A SHARP EDGE.

MAN WAS TIGHTENING A BOLT AND THE WRENCH SLIPPED. MAN HIT HIS HAND INTO A PIECE OF METAL.

INJURED WAS MOVING TIMBERS WITH A PRY BAR OVERHEAD HIS HANDS WERE WET AND HE WAS WEARING LEATHER GLOVES THE PRY BAR SLIPPED AND HIT INJURED ON THE CHEEK.

HIT WITH HAMMER PC OF STEEL BROKE OFF IN LOWER JAW

MAN WAS CUTTING INSULATION FROM WIRE HE RECEIVED THE DIRECTION OF THE CUT AND THE KNIFE CUT HIS HAND.