Buscar en el registro

Employee was baring out S1 chute hit right shoulder, went to continue to bar when EE felt a pop in EE's shoulder.

Employee was surveying blast hole collar when survey rod hit something causing it to twist and tip back against thumb.

Mechanic was tightening the fitting on a steering cylinder when the wrench slipped hitting mechanic in left front tooth and causing a chip to the tooth.

On 10/19/21, employee hammered a loader tooth pin. Metal came off, struck the employee's cheek, causing a cut. First aid was provided. Injury became reportable 11/11/21 when employee requested medical attention for prolonged irritation in the wound. Foreign metal body was removed and sutures were applied.

Employee was changing a bit on a blast hole drill when left hand was struck by a wrench resulting in a laceration and fracture to the left ring finger. The laceration was closed with sutures

Employee was using a hammer to break up some material when the hammer handle failed causing the hammer head to come back and strike the employee in the face. The impact resulted in a laceration to the lip that required sutures.

Employee was hand stemming blast holes with a shovel. Employee felt a pain in lower abdomen and was taken to ER. It was stated that employee had a small muscle tear in lower abdomen.

Removing a pin on the barrel end of a Tilt Cylinder of a 992G loader and didn't have the linkage secured. When the pin came out the cylinder slid forward and the bar that was being used to push the pin out struck the Right hand pinky finger. Broken Finger

Employee was stripping electrical cable when the utility knife he was using slipped causing a laceration to the upper portion of his right hand (web area between thumb and index finger) requiring 5 sutures to close.

Employee was using a hand pry bar to unlodge a rock in the crusher chute. The bar slipped pinching his right thumb between the bar and chute wall.

Employee was using a razor knife to cut open an electrical loom when the knife slipped cutting his left middle finger.

Wrenching down a bolt when wrench slipped off bolt and struck employee on tooth, chipping the tooth. No other injury involved.

EE WAS CHANGING A BEARING ON A CONVEYOR SHAFT AND STRUCK HIS LEFT THUMB WITH A HAMMER CAUSING A LACERATION WHEICH REQUIRED SIX STITCHES TO DOSE. HE WAS TREATED AT THE HOSPITAL EMERGENCY ROOM A ND RELEASED BACK TO FULL DUTY. T

EE WAS INSTALLING A SCREEN PANEL WITH A SLEDGE HAMMER. HAMMER GLANCED OFF PANEL AND STRUCK LT. INDEX FINGER. THE INJURY REQUIRED SEVERAL STITCHES TO CLOSE.

EMPLOYEE WAS LOWERING A HEAVY POWER CABLE FROM ACONVEYER FRAME USING A CHAIN WHICH SLIPPED. THE CABLE FELL AND THE EMPLOYEE'S FINGER WAS PINCHEDBETWEEN CHAIN AND CONVEYER FRAME. WHEN HE PULLED HIS FINGER OUT OF THE PINCH POINT HE RECEIVED A LACERATION WHICH REQUIRED MEDICAL TREATMENT (SUTURES).

EE WAS STANDING NEARBY WHILE MECHANIC WAS REMOVING A BJUCKET TOOTH ADAPTER WITH A V HAMMER. A SLIVER OF METAL CAME OFF THE ADAPTER AND STRUCK THE EE ON THE LEG. THE PIECE OF METAL BECAME LODGE D IN THE LEG AND HAD TO BE REMOVED AT THE LOCAL HOSPITAL. EE INITIALLY INFORMED SUPERVISOR THAT INJURY WAS ONLY A CUT. EE DID NOT TELL ANYONE HA HAD GONE TO THE HOSPITAL UNTIL 7-13-99.

EE WAS STRIKING A TABLE BUSHING SLEEVE ON A DRILL WITH A 2 LB. HAMMER, WHEN A PIECE OF METAL BROKE OFF THE HAMMER AND STRUCK HIM IN THE CHIN. THE LACERATION REQUIRED 2 STITCHES TO CLOSE.

AS EMPLOYEE WAS DRIVING LOCK PIN INTO LOADER TOOTH A SLIVER OF METAL BROKE OFF THE PIN WHEN HE HIT PIN WIHT HAMMER. THE SLIVER FLEW UP AND STRUCK HIM IN THELEFT ARM LODGING INHIS LEFT BICEP. H E WAS TAKEN TO THE DOCTOR WHERE THE SLIVER HAD TO BE SURGICALLY REMOVED. THE CUT WAS BANDAGED AND HE WAS RELEASED BACK TO WORK.

HELPER THOUGHT A WRENCH NEEDED TO BE USED TO SET CASING DRILLER LOWERED CASING, NOT KNOWING HELPERS HAND WAS BENEATH JAWS.

EE WAS SHOVELING WITH A FIBERGLASS HANDLED SHOVEL WHEN THE HANDLE BROKE & A SLIVER [APPROX 1 1/2"] WENT INTO THE 4TH & 5TH FINGERS OF HIS RIGHT HAND.

STRIPPING INSULATION FROM WIRE AND KNIFE SLIPPED OFF THE WIRE CUTTING LEFT HAND THUMB, NEEDING STITCHES.

HOLDING PIPE WITH PIPE WRENCH. STRIKING PIPE WITH HANMMER. PIECE OF METAL FLEW OFF AND HIT HAND.

EMPLOYEE WAS DISLODGING ROCKS WHICH HAD JAMMED ON CRUSHER FEED PLATE USING A LONG PRY BAR. ONE OF THE ROCKS HIT BAR AND HIS LEFT HAND WAS CAUSGHT BETWEEN BAR AND ACESS DOOR FRAME. SMASHED NDEX AND MIDDLE FINGER. INDEX FINGER WAS BROKEN.

EMPLOYEE WAS DOING VISUAL INSPECTION OF GYRATORY CRUSHER WHEN HE FOUND THREE ROCKS HUNG UP OF SPLITTER. HE THEN SHUT DOWN APRON FEEDER AND PROCEEDED TO BAR ROCKS OFF SPLITTER. ROCKS WERE STACK ED ON TOP OF EACH OTHER. HE HAD BAR BETWEEN BOTTOM ROCK AND SPLITTER EXERTING UPWARD PRESSURE WHEN ROCKS GAVE WAY ALL AT ONCE, CAUSING BAR TO ACCELL UPWARD PINCHING RING FINGER ON RIGHT HAND

EMPLOYEE STATES HE WAS INSTALLING A PORTABLE TANK ON SERVICE TRUCK TANK SLIPPED STRIKING MIDDLE & RING FINGERS ON RT HAND

EE WAS LOOSING NUT ON D-4 CAT. HE PULLED AND STRAINED HIS NECK HE WENT TO DR ON 9-6-91 THE DR DID AN ADJUSTMENT ON HIS NECK.

I NAME WAS IN THE BACK OF PUGMILL CLEANING DISCHARGE CHUTE WHEN A PIECE OF ORE CAME OUT HITTING HIS FOOT HE WENT TO DR ON 09-06-91 HE WAS GIVEN PAIN PILLS

EMPLOYEE WAS CHANGING OIL ON #C-89 DOZER,HE WAS USING HIS WRENCH WHEN IT SLIPPED CAUSING EMPLOYEE TO FALL STRIKING AND CUTTING HIS CHIN.

EMPLOYEE WAS REPLACING TEETH ON A 992 CAT LOADER BUCKET, AND THE INSTALL A TOOTH. THE EMPLOYEE HIT THE TIP WITH A 12 LB SLEDGE HAMMER, AT THIS TIME A PIECE OF METAL CHIPPED OFF THE TOOTH AND STRUCK HIS EYE SAFETY GLASSES AND THE GLASSES SHATTERED, GETTING CHIPS OF GLASS INTO HIS LEFT EYE.

USING HAND TOOL, METAL CUT EYE

HE WAS JUST PUSHING A SHOVEL INTO THE GROUND WHEN HE HURT HIS BACK.

EMPL CUTTING PIECE OF PIPE WITH CUT-OFF SAW WHEN PIPE WAS CUT THROUGH,IT TIPPED UP AND CUT EDGE STRUCK EMPL LEFT FOREARM.

EMPLOYEE WAS HOLDING A WRENCH USED TO TIGHTEN TRACK ON MOBIL CONVEYOR STACKER.ANOTHER EMPLOYEE WAS HITTING THE WRENCH WITH A SLEDHE HAMMER.THE WRENCH SLIPPED,HE GRABBED IT AND WAS STRUCK BY TH E HAMMER.

EMPLOYEE WAS CHANGING RIPPER SHANK ON D8L CHUNK OF STEEL BROKE OFF AND WENT INTO LEG.

EMPLOYEE WAS INSTALLING A LINER ON A SHAFT HOUSING HE WAS PRYING THE LINER WITH A STEEL PRY BAR THE PRY BAR SLIPPED AND STRUCK HIM IN THE MOUTH.

EMPL WAS COLLECTING CRUSHED HEAD SAMPLE & AS SAMPLE TROUGH WAS POSITIONED INTO TRANSFER POINT ROCKS BOUNCED OFF OF SAMPLE TROUGH & STRUCK HIM IN LEFT EYE KNOCKING HIS SAFETY GLASSES OFF & SOME OF DIRT WENT INTO HIS LEFT EYE.

EMPLOYEE WAS CHANGING ROLLERS ON A CONVEYOR BELT AS HE WAS TAKING A NUT FOOSE HIS WRENCH SLIPPED AND STRUCK HIM IN THE TEETH NOTE EMPLOYEE DID NOT GO TO SEE DR TIL 3-20-88 I WAS NOT NOTIFIED O F INJURY TIL 4-13-88 DIRECTOR REPORTING PRODCUDRE WERE EXPLAIN TO THIS EMPLOYEE.

CO-WORKERS WERE USING A 4 LB HAMMER AND A STEEL PUNCH TO KNOCK LOOSE A HANDLE ON A 8" VALVE WHICH WAS IN A VISE ON A WORK BENCH, HOLDING THE PUNCH WITHA VISE GRIP "C" CLAMP. INJURED PERSON WAS STANDING BACK AND TO THE SIDE ABOUT FIVE FROM THE WORK BENCH. WHEN THE CO-WORKER HIT THE PUNCH WITH THE HAMMER, THE PUNCH FLEW UP AND BACK HITTING THE INJURED PERSON IN THE MOUTH.

EMP WAS PRYING 2N A BOULDER WITH A 2" X 10' PIPE THE PIPE SLIPPED AND CAUGHT THE EMPLOYEES FINGER BETWEEN THE PIPE AND A BRACKET