Buscar en el registro

EES WERE ATTEMPTING TO UNCHOKE #2 CLAY SILO BY USING A PRYBAR & HAMMER WHEN EE STRUCK BAR WITH HAMMER A FOREIGN OBJECT FLEW INTO HIS LEFT EYE.

EE WAS SWINGING A 16 LB SLEDGEHAMMER ON AN UNEVEN SURFACE WHEN HE TWISTED HIS RIGHT KNEE.

EE WAS USING A PRY BAR TO OPEN A VALVE TO SILO. WHILE APPLYING SUBSTANTIAL PRESSURE, EE STRAINEDHIS RIGHT SHOULDER.

EE WAS USING PRY BAR ATTEMPTING TO UNCHOKE CHUTEWHEN PRY BAR SLIPPED SMASHING FINGER AGAINST CHUTE

INJURED WAS HANGING REBAR INSIDE DOME...IN MAN-BASKET OF P&H 50 TON CRANE. THE GROUND UNDER CRANES LEFT FRONT OUTRIGGER SUBSIDED AND THE CRANE LURCHED FORWARD, CAUSING BASKET TO EE UP AND DOWN . INJURED STRUCK HIS FACE ON STACK OF REBAR IN BASKET.

EMPLOYEE WAS PULLING ON A PIPE WRENCH TO FREE A PUMP RUNNER. WHEN THE RUNNER BROKE FREE, THE RESULTING JOLT INJURED EMPLOYEE'S SHOULDER.

EE WAS USING A SLEEVER BAR TO BREAK STEEL BAND ON PALLET. AS BAND BROKE, EE STUCK SELF IN (L) FOREARM WITH SHARP END OF SLEEVER BAR.

EMPLOYEE WAS INSTALLING BOLTS IN SLIP FLANGE OF SCREW CONVEYOR. AS HE WAS TIGHTENING THE BOLTS WITH A WRENCH, THE UPPER CONVEYOR'S WEIGHT SHIFTED, CAUSING THE SLIP FLANGE TO COLLAPSE, PINCHIN G EMPLOYEE'S LEFT HAND.

EE WAS ADJUSTING KILN BULL GEAR WITH HAMMER WRENCH & 4# HAMMER AND STRUCK LITTLE FINGER WITH HAMMER.

IMPROPER PLACEMENT OF HAND - BUILDING WOODEN FORMS USING HAMMER & NAILS TO SECURE WOOD.

EE WAS ASSISTING IN THE INSTALLATION OF DUST COLLECTION CHUTE FOR K-1152 AS THE CHUTE WAS BEING LIFTED IT CAME OFF THE COME-ALONG HOOK AND FELL ABOUT 8' TO THE DECK BELOW. AS THE CHUTE FELL, T HE FLANGED END CONTACTED EE'S (L) FOREARM, CAUSING A LACERATION.

EE WAS SWINGING A HAMMER WHEN IT BOUNCED BACK FROM THE WORK AND STRUCK HIM THE FOREHEAD.

EMPLOYEE WAS USING A BAR TO REMOVE CEMENT FROM AN OVERHEAD SCREW CONVEYOR. AS HE STRUCK THE CASING WITH THE END OF THE BAR, HE FELT A BURN- ING SENSATION IN HIS GROIN. THIS INJURY WAS DETERMINED WORK-RELATED ON 5/2/2000.

WENT TO CHECK ON #6 CLINKER FEEDER. IT WAS CHOKED OFF WITH CLINKER CHUNKS. HE STARTED WORKING ON IT HIMSELF WITH A PRYBAR. HE WAS GOING TO HIT THE CHUNKS ONE MORE TIME BUT AS HE PULLED THE BAR BACK HE JAMMED HIS THUMB ON THE SPRING THAT HOLDS THE FEEDER IN PLACE. AFTER 30 MINUTES HIS THUMB STARTED TO SWELL.

EMPLOYEE WAS INSTALLING A SYMONS CONCRETE FORM. AS EMPLOYEE ATTEMPTED TO ALIGN FORM PANELS, HE STRUCK THE FORM PANEL WITH A HAMMER. THIS CAUSED THE MIDDLE SET OF LOCKING PINS AND WEDGES TO SEP ARATE. ONE OF THE WEDGES FROM THE MIDDLE SET, STRUCK THE EMPLOYEE IN THE MOUTH, CHIPPING RIGHT FRONT TOOTH AND FRACTURING RIGHT INCISOR TOOTH.

EE WAS PRYING A PIECE OF ROCK FROM BETWEEN ROLLER AND BELT, AND ROLLER SLUNG PIPE AND CAUGHT EE ACROSS THE JAW AND UNDER LEFT EYE.

EMPLOYEE WAS USING AN ADJUSTABLE WRENCH TO TIGHTEN A BOLT. THE WRENCH SLIPPED AND STRUCK HIM, HITTING HIS LOWER LIP.

USING A BAR (APPROX. 12' LONG) TO CLEAN 209 FEED HOPPER HE PULLED HIS RIGHT ARM. NOTIFIED SUPERVISOR 12/30/98 AND WENT TO HAVE IT SEEN BY DR.

TIGHTENING HEAD BOLT ON 625 PUMP, PULLING UPON WRENCH STRAINED BACK & LOWER NECK

REPLACED A SHAFT ON THE APRON FEEDER. USING A COME-A-LONG TO LIFT THE SHAFT INTO PLACE. IT SLIPPED DOWN THE ANGLE IRON PINCHING THE 3 FINGERS.

EE WAS PULLING A BEARING FROM A CEMENT PUMP HOUSING. IT POPPED LOOSE AND CRUSHED THE END OF HIS MIDDLE FINGER ON HIS LEFT HAND. IT ALSO TWISTED HIS WRIST.

EE WAS SWINGING A 10# SLEDGE HAMMER. HE MISSED THE WORK DURING A SWING AND HIS ARM WAS CAUGHT BETWEEN THE HAMMER HANDLE AND A STEEL RAIL WRIST REQUIRED SPLINT

REMOVING BEARING ON 625 F.K. PUMP WHEN TIGHTENING THE BOLT THE WRENCH SLIPPED OFF AND EE FELL BACKWARDS, BODY HIT WALL AND KNEE TWISTED.

EE WAS SQUATTING TO SERVICE A BEARING WHEN HE FELT PAIN.

EE WAS USING A STEEL BAR AND SLEDGE HAMMER TO REMOVE A MATERIAL BUILDUP FROM AN ELEVATOR FEED CHUTE. THE SLEDGE HAMMER SLIPPED, THE EE'S FINGER WAS CAUGHT BETWEEN THE HAMMER HANDLE AND THE BAR . FRACTURE WAS DIAGNOSED ON 9-18-97.

CUTING MIAG LINK IN TWO AND WAS HITTING THE LINK WITH 2 LB. HAMMER TO BREAK APART WHEN A A METAL FRAGMENT FLEW INTO LFT ARM, PIERCING LEFT UPPER ARM.

EE'S FINGER WAS CAUGHT BETWEEN A STEEL BAR, WHICH HE WAS USING TO OPEN RAILCAR DOORS, AND THE GROUND.

WORKING ON 160 COUNTERWIEGHT, TO RAISE WEIGHT OFF OF BELT SPLICE, PULLING CHAIN ON CHAINFALL ANDINJURED BACK. STRAINED UPPER BACK AND NECK.

EE WAS USING A BOOMSUPPORT FOR REMOVAL AND INSTALLATION OF COMPRESSOR HEAD FOR FULLER ROTARY COMPRESSORS. THE BOOM REQUIRES A BOLT TO BE THREADED INTO THE LIFTING THREAD OF THE COMPRESSOR FOR SUPPORT. EE WAS USING THE BOOM DURING THEINCIDENT TO INSTALL THE HEAD ON THE COMPRESSOR WHEN THE SUPPORT BOLT PULLED OUT FROM THE THREADS OF THE LIFTING HOLE. EE WAS KNOCKED BACKWARDS AND FE

EMP , MECHANICAL REPAIRMAN, WAS IN PROCESS OF HOOKING A WELDING TRAILER UP TO FOUR WHEEL CART. TONGUE OF WELDER CART WAS NOT A HINGED TYPE AND HAD TO BE PRYED UP INTO POSITION TO CATCH HOOK ON CART. DURING PROCEDURE, EMP STRAINED HIS LOWER BACK, PRODUCING LUMBAR STRAIN. WILL BE ON LIGHT DUTY UNTIL 10-1-96. REPORTED ACCIDENT 9-25-96.

EE AND OTHER EE WERE IN THE PROCESS OF REMOVING THE FULER KINYON PUMP SCREW FROM THE EAST KILN FEED PUMP 626. DURING THIS PROCESS EE HAD TO USE A PRY BAR TO WORK THE SCREW OUT OF THE BARREL HO USING. USING THE BAR, EE STRAINED HIS LOWER BACK. HE WAS USING THE PRY BAR WITH A BACK AND FORTH MOTION TRYING TO DISLODGE THE SCREW. HE IS ON RESTRICTED DUTY.

SUDDEN MOVEMENT OF WRENCH CAUSED PAIN IN RIGHT ELBOW. WAS REPORTABLE ON 8-21-96 WHEN HE RECEIVEDPHYSICAL THERAPY.

EMPLOYEE WAS WORKING IN THE CLINKER COOLER REMOVING COOLER SIDE CASTINGS WITH A CHAIN-FALL(CUM-A-LONG). THE HOOK ON THE CHAIN FALL WAS ATTACHED TO THE CASTING FOR REMOVAL. TENSION WAS APPLIED TO THE CHAIN AND DURING THIS PROCESS, THE CASTING FRACTURED & THE CHAIN & HOOK RETRACTED, STRIKING EMPLOYEE IN HIS RIGHT SHIN AREA. HE RECEIVED 6 SUTURES TO HIS RIGHT SHIN & THEN RETURNED TO W

EE CUT LEFT THUMB WITH A UTILITY KNIFE WHILE TRIMMING A PIECE OF RUBBER CASTING ON BOTTOM OF BLEULER MILL. CONTRIBUTING & DIRECT CAUSE WAS THE IMPROPER PLACEMENT OF HAND & CUTTING TOWARDS SAID HAND. 8 SUTUTES WERE REQUIRED TO CLOSE SAID WOUND. EE TO RETURN FOR FOLLOW-UP ON 1/15/96 FOR REMOVAL OF SUTURES & EXAM. NO RESTRICTIONS OR LOST DAY INCURRED.

EMPLOYEE WAS CLEANING A MATERIAL BUILD UP. FROM A CHUTE WHEN HE STRUCK HIS LOWER LIP WITH A STEEL BAR.

EMPLOYEE WAS USING A SLEDGE HAMMER TO STRIKE A STEEL CEMENT SILO CONE WHEN HE FELT A PAIN IN HIS BACK.

EE WAS PULLING ON CHAIN OF COME-A-LONG WHILE WORKING ON 1123 SCREW. HOOK OF COME-A-LONG SLIPPED AND IT CAME LOOSE AND CAUSED EE TO FALL. HIT HIM IN THE FACE. WHEN HIT ALSON FELL ON BUTTOCK, HU RTING BACK. BACK SPRAINED.

EMPLOYEE WAS SWINGING A SLEDGE HAMMER WHEN HE FELT PAIN IN HIS GROIN.

EMPLOYEE WAS USING A HAMMER TO STRIKE A DRIFT PIN WHEN HE MISSED THE PIN AND STRUCK HIS HAND.

EMPLOYEE WAS OPERATING MANUALLY A HOIST CRANKING IT DOWN THE HANDLE SLIPPED FROM HIS HAND & HE REACHED ACROSS TO PULL UP ON THE BRAKE WHEN DOING SO HIS INDEX & MIDDLE FINGER WERE SMASHED BETWE EN DRUM & HANDLE/RT INDEX & MIDDLE FINGERS REQUIRED STITCHES

EE WAS USING THE VICE. HE HAD IT TIGHTENED AND WAS PULLING ON THE HANDLE TO GET IT LOOSE. WHEN IT STARTED TO LOOSEN HAND SLIPPED. WHEN HAND SLIPPED THE VICE CAUGHT HIS LITTLE FINGER AND WRAPPE D IT AROUND THE VICE HANDLE. HE WAS INTO A STRONG PULL AND COULD NOT STOP BEFORE IT WAS TOO LATE. THE VICE DIRECTLY CAUSED DAMAGED TO EE S FINGER HIS LITTLE FINGER LAST JOINT RIGHT HAND SUFFE

AS EMPLOYEE WAS USING A 15" ADJUSTABLE WRENCH TO TIGHTEN BOLTS THE WRENCH SLIPPED CAUSING HIM TO FEEL PAIN IN THE LOWER LEFT SIDE OF HIS BACK.

INJURED EMPLOYEE WAS HOLDING A PIN WITH A SET OF LOCKING PLIERS. AS A FELLOW EMPLOYEE STRUCK THE PIN WITH A SLEDGE HAMMER THE PIN CAME FREE INJURING THE EMPLOYEE.

EMPLOYEE WAS PULLING ON A 30IN BAR TO LOOSEN THE BOTTOM LUG OF A SILO VALVE WHEN HE INJURED HIS BACK

EMPLOYEE WAS USING A WRENCH TO INSTALL A BOLT AND NUT WHEN THE WRENCH SLIPPED CAUSING AN ABRASION. FINGER LATER BECAME INFECTED WHICH THEN MADE IT REPORTABLE.

POKING MATERIAL BUILD-UP IN A STORAGE BIN TO GET MATERIAL TO FLOW. WAS REPEATEDLY USING A 3/4" ROD TO POKE WITH.

EMPLOYEE WAS PUSHING ON A STEEL BAR TO OPEN A SILO GATE WHEN HIS LEFT HAND SLIPPED FROM THE BAR THIS JOLT CAUSED A DULL PAIN TO BE FELT IN HIS NECK ON 07-19-93 HE WENT TO A DOC & WAS GIVEN RES TRICTED DUTY

WORK WAS TAKING PLACE ON THE NOSE RING OF THE KILN REMOVING NOSE RING CASTINGS. USING PRY BAR TO REMOVE WASHERS FROM BOTTOM OF CASTINGS, THE PRY BAR GLANCED OFF THE CASTING AND THE LEFT HAND L ITTLE FINGER STRUCK THE CASTING. EMPLOYEE STATES THAT WHILE REMOVING A WASHER FROM NOSE RING CASTINGS, HIS PRY BAR SLIPPED, MASHING HIS FINGER AGAINST THE NOSE OF THE KILN. SUTURES WERE REQUI

EE WAS USING PRYBAR TO SHUT FEEDER GATE BAR SLIPPED AND HIT RIGHT HAND ON HANDRAIL BETWEEN BAR AND HANDRAIL, CUTTING A BRAKING RIGHT MIDDLE FINGER INJURY REQUIRED EIGHT 8 SUTURES TO CLOSE.

EMPLOYEE STATES THAT WHILE REMOVING THE INNER RACE OF A BEARING FROM THE SHAFT, HE STRUCK IT WITH A HAMMER AND A PIECE OF THE INNER RACE BROKE OFF AND ENTERED EMPLOYEE'S UPPER LEFT LEG. LEFT U PPER LEG WAS INJURED WHEN METAL CHIP BECAME IMBEDDED IN LEG. FOREIGN BODY REMAINS IN EMPLOYEE'S LEFT UPPER LEG.