Buscar en el registro

Employee was changing the skid steer from loader bucket to forks and was using a cheater pipe to assist him. The pipe slipped and employee smashed his fifth finger on his right hand.

Employee was kneeling down cutting a conveyor belt with a knife. THe knife slipped and the employee cut his left thigh 2" deep above the knee.

THE WORKER WAS CLEARING G-CONE FROM A LOADER TOOTH BY STRIKING IT WITH A HAMMER. A PIECE OF METAL BROKE OFF AND ENTERED HIS THIGH.

THE EE WAS USING A SLEDGE HAMMER TO REMOVE TOOTHON THE LOADER BUCKET & IT SPLINTER OFF & HIT HISFOREARM

WHILE CLEANING OUT THE BARMAC CHUTE, THE EE HIS A PIECE OF ANGLE IRON WITH HIS RIGHT ELBOW.

CLEANING SCREEN OF ROCK BY HAMMERING & FOREIGN BODY ENTERED EYE UNDER SAFETY GLASSES

USING A HAMMER TO SPLIT APART A DRIVE COUPLING TO INSTALL A RUBBER WEAR SPYDER. THE EE DID NOT SEEK MEDICAL TREATMENT UNTIL 12/10/98 NOR DID HETELL ANYONE ABOUT HIS INJURY UNTIL 12/10/98

WHILE TENSIONING GEAR BOX WITH JOHNSTON BAR THE BAR SLIPPED DOWNWARD, CAUSING LOSS OF BALANCE AND PUNCTURED HIS LOWER LEFT FRONT LEG.

THE EE CRUSHED HIS RIGHT KNEE BETWEEN THE ROTOR BLOW BAR AND ACCESS DOOR WHEN THE WEDGE WAS REMOVED FROM THE LOCKING ROTOR IN PLACE TO SOON.

WHILE HAMMERING ON VERY BRITTLE CRUSHER PARTS A CHIP FLUNG OFF AND CUT RIGHT INDEX FINGER.

THE EMPLOYEE TRIED TO PRY OUT A ROCK BETWEEN THE GRIZZLEY WITH A 4' BAR. AS HE STRUCK THE ROCK, HE LOST HIS GRIP AND THE BAR STRUCK HIM IN THE SHOULDER.

THE EMPLOYEE WAS REMOVING THE TOOTH OFF THE BUCKET AND AS HE STRUCK THE TOOTH WITH THE CLAW HAMMER A FRAGMENT OF METAL CAME OFF THE BUCKET AND WENT INTO HIS LEFT UPPER LEG.

EE WAS PUTTING IN A NEW LINER IN THE CANICA CRUSHER. PRY BAR SLIPPED AND HIT HIS LEFT ELBOW.

REPLACING BUCKET TEETH ON 988B WHEEL LOADER. WASDRIVING NEW TEETH IN WITH 8LB HAMMER AND A PIECEOF METAL PENETRATED NECK.

AS THE EMPLOYEE REMOVED THE PINS THE HYDRAULIC JACK HANDLE SLIPPED OUT AND HIT HIM IN THE FACE.

THE EE WAS PUTTING THE SLEDGE HAMMER BACK INTO THE HOLDER. HE DID NOT RELAIZE THAT HIS FINGER WAS STILL NOT CLEAR ON THE LAST INCH OF THE EDGE AND WHEN THE SLEDGE HAMMER CAME DOWN IT CUT THE T IP OF HIS FINGER.

THE EMPLOYEE WAS CUTTING A BELT FOR THE CARROUSEL CRUSHER. AS HE WAS CUTTING THE UTILITY KNIFE WENT THRU THE BELT AND CUT HIS RIGHT LEG ABOVE THE KNEE.

AS THE EMPLOYEE WAS HAMMERING, HE HIT HIS LEFT THUMB WITH THE HAMMER BETWEEN THE WALL AND THE PLACING WEDGE.

THE EMPLOYE EWAS CUTTING A PLASTIC WATER HOSE. AS HE WAS CUTTING, THE UNTILITY KNIFE SLIPPED OUT OF HT EHOSE AND CUT HIS LEFT TOP OF HIS HAND BETWEEN THE INDEX FINGER AND THUMB.

THE EMPLOYEE WAS USING A SLEDGE HAMMER TO TIGHTEN UP A NUT ON TOP OF A CONE CRUSHER.

WHILE THE EE WAS ADMJUSTING THE SHORT HEAD CONE CRUSHER THE COME A LONG SLIPPED CAUSING PAIN IN HIS RIGHT ELBOW.

WHILE THE EMPLOYEE WAS CLEANING OUT THE CHUTE OF THE FEEDER WITH A 5/8"X6' BAR HE WAS MOVING IT UP AND DOWN TO CLEAN THE CHUTE AND AS HE WAS GOING UP WITH THE BAR HE HIT HIMSELF IN THE NECK WI TH THE BAR.

THE EMPLOYEE WENT TO RELEASE PINS ON A 600 WA BAY LOADER AND AS HE WAS DISCONNECTING THE BUCKET THE BRASS BAR SLID AND HIT HIM IN THE FACE.

WHILE PUSHING DRIVE DOWN ON A LOADER WITH A SHORT HANDLE SLEDGE HAMMER HE STRUCK AN OBSTRUCTION OVERHEAD CAUSING IT TO REBOUND AND HIT HIS LEFT ARM.

HE WAS REMOVING A PIN FROM A TRIPLE DECKER SCREEN THE PIN WAS UNDER PRESSURE POPPED OUT & STRUCK THE EMPLOYEE ABOVE THE LEFT EYE

THE EMPLOYEE WAS REMOVING RIPPER TEETH FROM A DOZER WHEN A PIECE OF METAL CHIPPED OFF AND ENTERED HIS LEFT CALF.

HE WAS WORKING ON A 359 GNERATOR WITH A WRENCH. HIS WRENCH SLIPPED OFF A NUT CAUSING DAMAGE TO HIS LEFT WRIST.