Buscar en el registro

Unchoking a chute with limestone. Jammed right shoulder.

Using a large wrench and it slipped off a nut, momentum caused person to fall on back. After diagnostic visit (07/10) placed on restrictions.

Hammering on a block, the hammer skipped on the edge and ended up hitting the employee's right hand/wrist. Employee did not seek medical attention until 01/20/2025. With this appointment employee was placed on restrictions of 10lbs push/pull, 10lbs carry/lift with right wrist. Employee came back to work after appointment with brace on wrist.

Employee strained right shoulder while operating a come-a-long in an awkward position. Diagnostic treatment until rotator cuff surgery performed on June 22, 2023.

Was tightening bolts when one of the wrenches EE was using slipped off the bolt. The bolts were at eye level and the employee was standing while conducting this work. EE was using an adjustable spud wrench and a box end wrench to tighten bolts. Due to the force and angle, the spud wrench slipped and struck them under right eye.

While rebricking the kiln, a pogo slipped off the brick it was holding causing the brick to fall on the employee's finger.

EE was hitting a stiffener ring on a duct with a 16 pound sledge hammer. The hammer glanced off the ring pinching EE's finger between the ring and the hammer handle. EE was wearing gloves.

Trimming off black expansion material with utility knife and using the knife in an improper manner cutting towards self. Cut through the glove causing a laceration on EE's left hand.

EE was operating a chain hoist while looking up when dust fell from the hoist. Some of the falling dust got around EE's safety glasses and entered EE's right eye causing irritation.

Employee was tightening bolts on expansion joint at the chiller pad. Ratchet slipped and struck employee on EE's right cheek.

Employee was swinging a sledgehammer, when finger was caught between the handle and the manhead pin, resulting in broken finger. Physician prescribed restricted duty.

Employee was swinging sledgehammer to dislodge manhead for Ball Mill, sledgehammer bounced off of manhead. As Employee sought to control the hammer and keep it from falling, they strained a shoulder. Employee did not feel medical attention was necessary until a week later, as discomfort continued. Physician prescribed lifting restrictions and physical therapy.

EE was using heavy pry bar to clean material from clay shredder, when strain occurred. EE did not feel immediately necessary to be evaluated medically. approximately 1 week later, physician diagnosed as thrombosed external hemorrhoid. Procedure performed to drain, employee prescribed restricted duty.

Employee was chipping slag with a jitter bug. a piece of slag shot up and burned the area between the bridge of the nose and the left eye.

EE was driving shim between refractory bricks, when ee struck thumb with the hammer. Physician treated thumbnail and prescribed antibiotic/anti-inflammatory medication.

Employee was holding a pin as his partner was striking pin with hammer. The hammer hit the side of the pin, and struck the employee's hand. Physician prescribed anti-inflammatory medication. Employee was not limited in work duties.

As ee was striking the outside of a chute to clear material inside, the rubberized hammer he was using skidded/slipped off chute, causing employee to strain back. The incident was not reported, the employee continued to work, on 10/18 the employee called in without explanation, and did not work that day. On 10/19, after reporting the incident, physician prescribed limited duty.

Employee was removing seal from kiln trunion housing, when tool being used slipped out of the handle, straining right bicep muscle. Physician prescribed limited use of arm.

EE strained shoulder dislodging buildup with bar. EE requested medical examination approx. 1 1/2 month after incident due to continued discomfort. Physician prescribed anti-inflammatory medication but no restrictions. **EE underwent surgery for continued discomfort on 11/11/10. One lost workday and 60 restricted workdays resulted from this surgery.

EE attempting to move shaft with pipe wrench, which slipped causing EE to twist ankle and injure nose on handrail.

EE struck bearing with hammer causing a metal splinter to be expelled, striking EE and became embedded in forehead. Physician removed splinter.

EE was using a sledge hammer to tighten bolts on raw mill drive motor, and reportedly missed target, straining muscle in his back.

EE was cutting rubber hose with pocket knife, when knife slipped off hose and cut right hand. Physician applied 3 stitches.

Employee picked up a sledgehammer and knocked out a metal shim under a steel plate. Allegedly a metal shaving ricocheted off & struck employee in the abdomen embedding the fragment of metal.

The employee was installing a split rubber seal on a dust collector door under silo 50. He was cutting the seal material with hisutility knife when it hung up in a corner of the door. He reaced down with his left hand to free it and it came free cutting his left index finger.

While the employee was attempting to clear a choke in the preheater, hot material flushed out of a door burning his legs.

The ee was attempting to clean buildup in a chute with a punch bar. the punch bar slipped resulting in the ee right hand being mashed into the side of the chute. as a result his right fingers were injured.

The employee was attempting to remove an old chain link from a drag. The employee and his partner were using comalongs when the hook came off and hit the employee's thumb.

THE EE WAS REMOVING WOODEN COUPLING PINS FROM COMPRESSOR. THIS JOB REQUIRES DRIVING THE PINS OUT WITH A HAMMER IN TIGHT QUARTERS. HIS HAMMER HIT THE MOTOR NEXT TO THE COMPRESSOR, CREATING A GLANCING BLOW, CAUSING THE HAMMER TO STRIKE THE EE'S LEFT FINGERS.

PLACING BURNER PIPE. HELD UP WITH COMEALONG. WENT TO PLACE A BRICK UNDER PIPE. CHOKER ROLLED AND PIPE CAUGHT END OF FINGER CAUSING LACERATION OF FINGER.

EE WAS TORQUING BOLTS ON RAYMOND COAL MILL REDUCER WITH 1 5/8" COMBINATION WRENCH WHEN IT SLIPPED OFF BOLT AND HIT HIM ON RIGHT FOREHEAD.

EE WAS SWEEPING BURNER FLOOR WHEN HOT DUST BLEW INTO HIS EYES.

EE WAS TRYING TO UNCHOKE #2 SWING TANK, WHEN HE HIT THE HACKHAMMER WITH A HAMMER CAUSING A PIECE OF STEEL TO HIT HIM IN CHEST.

EE WAS USING A PRY BAR TO LINE UP RAYMOND COAL MILL WHEN THE BAR SLIPPED, HITTING 3RD FINGER, LEFT HAND.

EMPLOYEE WAS REMOVING JIB OUT OF MOBILE CRANE. EMPLOYEE KNOCKED ALL THE BOLTS OUT (4) CAUSING THE BOOM JIB TO COME LOOSE. IT DROPPED APPROXIMATELY TWO INCHES TO THE GROUND. EMPLOYEE NEGLECTED TO REMOVE HIS LEFT FOOT UNDER THE JIB BFORE REMOVING THE BOLTS.

EMPLOYEE WAS BEATING ON RAIL CAR DOOR, TRYING TO CLOSE IT, WHEN THE BAR THAT HE USED TO BEAT THE DOOR SLIPPED, HE FELT PAIN IN HIS BACK.

EMPLOYEE WAS SWEEPING UNDER THE TAILDRUM OF THE OVERLAND CONVEYOR BELT,WHEN HE HURT HIS BACK.

EMPLOYEE WAS USING A HAMMER TO TIGHTEN A BOLT ON THE ROLLER PRESS WHEN HE FELT PAIN IN HIS LOWER BACK.

EE WAS PULLING A BEARING AT THE CLAUDIUS PETERS PUMP WITH A BEARING PULLER, WHEN THE BOLT IN THE PULLER BROKE STRIKING EE IN THE LEFT EYE.

EMPLOYEE WAS HOLDING A GUARD AT #1 CLINKER BELT WHILE EE WAS HITTING THE GUARD WITH A HAMMER WHEN EE HIT EE FINGER WITH THE HAMMER THERE WERE DUSTY CONDITIONS

EMPLOYEE WAS USING KNIFE O SKIN A WIRE TO HOOK UP A COMPRESSOR WHEN THE KNIFE SLIPPED CUTTING HIS LEFT THIGH

54736YEE WAS USING A 2 POUND HAMMER TO CLEAN SCREEN IN #1 FINISH MILL WHEN A PIECE OF METAL INJURED HIS FINGER.

55061S STRIPPING THE ELEVATOR TRACTION WHEN HE STARTED TO TAKE THE BOLTS OUT OF THE BEARINGS HE CUT THME WITH A TORCH AND THEN HE HIT THEM WITH A B&O HAMMER TO KNOCK THEM OUT A PIECE OF METAL 38977ED OFF THE B&O HAMMER INJURING HIS FINGER.

EMPL INJURED LOWER BACK WHILE WATERBLASTING ON RPREHEATER RISER DUCT.

EMPLOYEE WAS CUTTING A DRIVE BELT WITH A KNIFE HE PULLED T HE KNIFE TOWARD HIMSELF WHILE CUTTING THE BELT KNIFE SLIPPED CUTTING HIS RT ARM

EMPLOYEE WAS USING A SLEDGTE HAMMER TO HIT THE MANHEAD ON #2 FINISH MILL WHEN HE CAUGHT HIS LEFT FINGER INDEX BETWEEN THE HAMMER & A BOLT HE HAD THE ACCIDENT ON 02-05-91 & WENT TO THE DOC ON 0 2-08-91

THE EMPLOYEE WAS IN BOTTOM OF DRAG HAVING TO TIGHTEN UP BOLTS THAT WAS OVER HIS HEAD,CAUSING A STRAIN IN HIS NECK.

HE WAS REOVING BOLTS FROM A FLANGE WHEN A WRENCH SLIPPED AN STRUCK HIM ABOVE THE EYE.

EMPLOYEE HAD PUT COUPLING ON SPEED REDUCER SHAFT AND WAS DRIVING THE KEY WITH EIGHT POUND HAMMER WHEN HE FELT SHARP PAIN IN HIS BACK. HIS BACK BEGAN GETTING SORE.

EMPL DRIVING SL9EVE ONTO SHAFT WITH HAMMER PIECE OF STEEL WENT THROUGH GLOVE HITTING RIGHT HAND.