Buscar en el registro

Maintenance Electrician pinched right index finger between pipe wrench and bench vice while tightening a pipe fitting causing a laceration requiring 3 sutures.

Employee had an accident yesterday while ee was assembling a electrical cord. EE was using a screwdriver to tighten a screw when the screwdriver slipped and punctured hand. EE immediately cleaned it and applied a dressing, but today hand is quite swollen.

Employee was using an air lance and pry bar to break material free in the impactor chute. The material broke free and employee hit elbow on the top of the chute door causing bursitis on the elbow.

A DMS builders LLC employee cut his leg and required stitches resulting from cutting plastic pipe.

While removing waste rock from shovel bucket, rock cut lower right leg

While cutting banding material on a bundle of pipe, banding popped up, hit leather glove first, then up left arm, and cut left forearm.

Employee was holding a pin while another employee was using a sledge hammer and the hammer glanced off and crushed his finger.

While working on pipe valve wrench hit employee in face.

WHEN LOOSENING PIPE WITH WRENCH, PIPE BROKE LOOSE AND EMPLOYEE FELT PAIN IN LOWER BACK.

EE AND ANOTHER EE WERE INSTALLING A "SHIN GUARD" ON THE BUCKET OF AN HITACHI 1800 SHOVEL. THE SECOND EE WAS HOLDING AN END WRENCH ON A NUT WHILE THE INJURED EE RAN AN IMPACT WRENCH ON THE BOLT . THE END WRENCH SLIPPED AND CAUGHT THE INJURED EE ON THE FOREHEAD ABOVE THE RIGHT EYE. THE EE WAS TRANSPORTED TO THE LOCAL E.R. WHERE HE RECEIVEDX STITCHES.

WHILE USING A PIPE WRENCH TO TURN THE PULLEY ON THE 1 SILO BLOWER, EE HAND SLIPPED AND WAS CAUGHT BETWEEN THE BELT AND THE SHEAVE.

WHILE CUTTING GASKET MATERIAL WITH RAZOR KNIFE THE KNIFE SLIPPED AND CUT THUMB ON LEFT HAND REQUIRING STITCHES.

WHILE WORKING ON EQUIPMENT, TIGHTENING BOLT, THE WRENCH SLIPPED AND ELBOW HIT WALL. EMPLOYEE DID NOT SEEK MEDICAL ATTENTION UNTIL 1-8-98. EMPLOYEE WAS DIAGNOSED WITH TENNIS ELBOW.

WHILE USING A CROWBAR TO ADJUST PINS ON A BULKHEAD EE WAS PRYING THE DOOR INTO THE NEXT SLOT WHEN THE DOOR SPRUNG AND POPPED THE CROWBAR OUT OF HAND AND STRIKING EE IN FACE.

EMPLOYEE WAS DUMPING A TUBE AND HIT HIS THUMB WITH MALLOT.

EE WAS ALIGNING BOLT HOLES ON A LIFT CYLINDER WHILE INSTALLING A HOIST CYLINDER SUPPORTED BY A PRY BAR. THE PRYBAR SLIPPED WHILE EE WAS CHECKING HOLE FOR ALIGNMENT WITH FINGERS.

EMPLOYEE WAS PUSHING A PALLET ON TO A STRETCH WRAP TURN TABLE & FELT A PAIN IN GROIN AREA AFTER SEVERAL WEEKS, EMPLOYEE SAW DR. & WAS DIAGNOSED AS HAVING A HERNIA.

EMPLOYEE WAS CONNECTING COMPUTER EQUIP. CABLES./ SCREW DRIVER SLIPPED AND CUT PALM OF LEFT HAND.

ELMPLOYEE WAS USING HAMMER TO LOOSEN ROCK FROZEN IN ROCK INPUT BIN. PULLED OR STRAINED BACK.

54736YEE WAS WORKING W/ANOTHER MAINT PERSON REMOVING BOLTS FROM P&H SHOVEL THE OTHER MAIN MAN PULLED ON A WRENCH TO GET SLACK IN HOSE WRENCH HIT EMPLOYEE IN THE MOUTH

EMPL WAS TRYING TO CUT A GLUE BUCKET WITH A KNIFE TO PUT A HANDLE ON IT THE KNIFE BLADE FOLDED AND HIS FINGER GOT CAUGHT BETWEEN THE BLADE AND THE KNIFE HANDLE CUTTING HIS FINGER

EMPLOYEE WAS ATTEMPTING TO UNPLUYG AN INPUT CHUTE USING A LONG BAR SWINGING IT IN AN UPWARD MOTION WHILE SWINGING THE BAR THE EMPLOYEE STRUCK THE CHUTE DOOR WITH H IS HAND

EMPLOYEE WAS RE4OVING SEALER OFF OF CYCLONE DOORWAY WITH POCKET KNIFE. EMPLOYEE WAS CUTTING TOWARD BODY. KNIFE SLIPPED CUTTING FINGER OF LEFT HAND.

EMPLOYEE WAS CUTTING LOOSE WIRE CONNECTORS FROM A DRIVE MOTOR. VISIBILITY WAS REDUCED DUE TO A DUSTING PROBLEM FROM NEARBY EQUIPMENT. ALSO EMPLOYEE WAS CUTTING TOWARD BODY. KNIFE SLIPPED CUTTI NG LEFT HAND REQUIRING STITCHES.

EMPLOYEE WAS ATTEMPTING TO SEPARATE SECTIONS OF A 360 DOWNHOLE HAMMER UJSING A SLEDGE HAMMER WHILE SWINGING THE HAMMER HE FELT PAIN IN LOWER BACK.

INJURED EE WAS ASSISTING ANOTHER EE IN OVING A LENGTH OF 14" CHANNEL. THEY WERE USING PRY BARS TO LIFT & MOVE CHANNEL. WHILE MOVING CHANNEL SLIPPED OFF OF THE B AR CAUSING IT TO FALL ON H