Buscar en el registro

EMPLOYEE WAS USING A SLEDGE HAMMER TO HIT THE MAGNETITE BIN IN AN EFFORT TO UNPLUG IT. ON ONE OF THE BACK SWINGS HIS LEFT, MIDDLE FINGER WAS PINCHED BETWEEN THE HAMMER HANDLE AND A METAL SUPPO RT. THIS RESULTED INTO A LACERATION THAT REQUIRED SUTURES.

EMPLOYEE WAS CUTTING A PLASTIC BAND ON A SKID OF BLOCK WITH A RAZOR KNIFE. THE RAZOR KNIFE SLIPPED PUNCTURING HIS RIGHT THIGH. STITCHES WERE USED TO CLOSE THE CUT MAKING THIS A REPORTABLE INCI DENT. HE WAS SCHEDULED TO VACATION 4-25-01 TO 5-01-01.

THE TRACK CREW HAD BEEN INSTRUCTED TO RESET SOME TIMBERS AT THE 6 LEFT SECTION TRACK RUN AROUND. EE WAS HOLDING ONTO ONE TIMBER AS ANOTHER EE ATTEMPTED TO STRIKE IT WITH A TRACK HAMMER TO DISL ODGE IT. THE HAMMER STRUCK EE ON THE TIP OF HIS LEFT MIDDLE FINGER, FRACTURING IT.

EMPLOYEE WAS USING A SLATE BAR TO ADJUST THE SKIRTING ON THE G2 SILO BELT. THE SLATE BAR SLIPPED AND HIS LEFT THUMB STRUCK THE BELT AND AN IDLER, RESULTING IN A CHIPPED BONE TO THAT THUMB. A R EPORT ON THIS INJURY WAS NOT MADE UNTIL 2-7-01.

EE WAS PULLING ON A SPANNER WRENCH REMOVING A CATHEAD FROM THE GATE BOX. THE WRENCH SLIPPED OFF THE CATHEAD AND HIT EE IN THE FOREHEAD RESULTING IN A LACERATION REQUIRING STITCHES.

EE WAS HOLDING A SMALL SECTION OF 10 INCH PIPE OVER HIS HEAD WHILE ANOTHER EE INSTALLED BOLTS IN THE END PHLANGES. WHILE DOING THIS HE EXPERIENCED SOME LOWER BACK PAINS. EE RECEIVED MEDICAL AT TENTION FOR THIS INJURY, SHORTLY AFTER IT OCCURED, WHICH DID NOT MEET THE REPORTING CRITERIA. SINCE THEN HE HAS RECEIVED SHIROPRACTOR TREATMENTS. THAT INFORMATION WAS LEARNED ON 12-5-00.

EE WAS CUTTING A PLASTIC TIE WITH A RAZOR KNIFE. HE WAS CUTTING TOWARD HISMELF AND CUT THE BACK OF HIS LEFT HAND REQUIRING STITCHES.

EE WAS CUTTING A PLASTIC TIE WITH A RAZOR KNIFE. THE KNIFE SLIPPED CUTTING EE'S LEFT LITTLE FINGER.

EMPLOYEE AND A CO-WORKER WERE INSTALLING A LARGER MANDOOR IN A STOPPING. HE WAS USING A SLEDGE HAMMER TO MAKE THE OPENING LARGER. HE WORKED THE REMAINDER OF THE YEAR 2000 AND WENT OFF WORK 1-5 -01 FALLING BACK TO THE 6-3-00 INCIDENT.

EE WAS PUTTING A PLASTIC TIE ONTO HIS BELT HARNESS THAT WAS TO BE USED TO ATTACH HIS DUST MASK. WHILE CUTTING THE END OFF OF THE PLASTIC TIE, HE LACERATED HIS LEFT MIDDLE FINGER NEAR THE KNUCK LE. THIS LACERATION REQUIRED THREE SUTURES TO CLOSE.

EE WAS SLEWING OVER A RAIL AT THE END OF THE 3R3NE SECTION TRACK. AS HE WAS LIFTING AND PUSHING WITH THE SLATE BAR HE FELT PAIN IN HIS LOWER BACK.

EE WAS TRYING TO GET A TURNBUCKLE LOOSE ON A TAILPIECE. HE WAS PRYING UP ON IT WHEN HIS BACK STARTED HURTING. HE RETURNED TO WORK ON FRIDAY 2-11-00 BUT WENT OFF WORK THE NEXT WEEK MAKING THIS A LOST TIME INCIDENT.

EE WAS IN THE PROCESS OF PUTTING A DERAILED MANTRIP BACK ONTO THE TRACK. WHILE USING A LIFTING JACK AND BAR HE EXPERIENCED SOME PAIN IN HIS RIGHT LOWER BACK AND RIGHT ABDOMEN. RECENTLY HE STAR TED A SERIES OF PHYSICAL THERAPHY TREAMENTS FOR THIS INJURY.

EE WAS PUTTING A NAIL IN A HALF HEADER WHEN THE HAMMER HE WAS USING SLIPPED OUT OF HIS HAND AND STRUCK HIM ON THE LEFT SIDE OF HIS FACE BETWEEN HIS NOSE AND LIP.

EMPLOYEE WAS ASSISTING IN THE REPLACEMENT OF A 20 HP MOTOR ON A CLEAN COAL BELT HEAD. HE WAS USING A RED DEVIL TO LOWER THE MOTOR TO THE FLOOR WHEN THE CABLE GOT TANGLED UP ON THR REEL AND ALL OWED THE MOTOR TO DROP UNEXPECTEDLY AND STRIKE HIM. THIS RESULTED IN A LACERATION TO HIS LEFT ARM WHICH REQUIRED SIX STITCHES TO CLOSE THE WOUND

EMPLOYEE WAS WORKING WITH A CREW THAT WAS MOVING A TAILPIECE TO THE C-2 LONGWALL SECTION. THE LOWBOY BEING USED TO TRANSPORT THE TAILPIECE DERAILED AND THE CREW WAS ATTEMPTING TO PUT IT BACK ON TO THE TRACK USING AIR BAGS AND LIFTING JACKSEMPLOYEE USING A LIFTING JACK THAT KICKED OUT AND STRUCK HIM ON THE LEFT ARM AS THE LOWBOY WAS BEING RAISED. FRACTURE IN LEFT ARM.

EE WAS TIGHTENING BOLTS IN A SUB ASSEMBLY FOR A BELT SCRAPPER. HE SLIPPED OFF A BUCKET HE WAS STANDING ON AND STRAINED HIS LEFT HIP. EE RETURNED TO WORK BUT ON 11-20-99 HE REAGGRAVATED HIS HIP USING A STOPER DRILL AND MISSED 3 DAYS WORK.

EE WAS USING A UTILITY KNIFE RAZOR TO OPEN A CARDBAORD BOX THAT CONTAINED SOME MATERIALS THAT HE NEEDED. THE KNIFE SLIPPED AND STRUCK HIS RIGHT THUMB. THIS RESULT INTO A LACERATION THAT REQUIR ED SUTURES TO CLOSE.

EE WAS ASSISTING IN THE REPAIRING OF A CAT PAD FOR A D-6 DOZER. OTHER WAS USING A SLATE BAR TO LIFT THE PAD IN ORDER FOR EE TO TURN THE PAD OVER. THE SLATE BAR SLIPPED AND THE PAD DROPPED ONTO EE LEFT INDEX FINGER, LACERATING IT. SUTURES WERE REQUIRED TO CLOSE THE LACERATION.

EE WAS ASSISTING IN THE INSTALLATION OF A NEW BELT ON ONE OF THE RAW COAL SCREENS. HE WAS USING CHANNEL LOCKS TO PULL THE BELT IN PLACE WHEN THE CHANNEL LOCKS SLIPPED AND CAME BACK AND WHICH R EQUIRED 2 SUTURES TO CLOSE.

EE WAS HOLDING A TIMBER FOR ANOTHER EE . OTHE REE WAS TIGHTENING THE WEDGES TO HOLD THE TIMBER IN PLACE. EE ACCIDENTLY HIT THE TIP OF INJ EE'S LEFT MIDDLE FINGER FRACTURING THE TIP OF THE FIN GR. Y

EMPLOYEE WAS POSITIONING THE HEAD OF A PORTA-POWER TO PUSH A PIN OUT OF A STAB JACK ON A CONTINUOUS MINER. WHILE THE HEAD WAS BEING TENSIONED, EMPLOYEE'S FINGER WAS BETWEEN THE HEAD AND THE PI N THAT WAS TO BE REMOVED. TO MUCH PRESSURE WAS APPLIED TO THE PORTA-POWER AND THE END OF EMPLOYEE'S LITTLE FINGER ON LEFT HAND WAS PINCHED, FRACTURING THE TIP OF THE FINGER.

EE WAS ASSISTING IN THE REMOVAL OF A MOTOR FROM A CLEAN COAL SCREEN. A "RED DEVIL" COME-A-LONG HAD BEEN USED TO RAISE THE MOTOR INTO THE AIR AND A CHAIN FALL WAS GOING TO BE USED TO MOVE IT FR OM THAT POINT. BEFORE THE CHAIN FALL WAS ATTACHED THE MOTOR SWUNG AROUND AND STRUCK HIS RIGHT LEG, LACERATING IT. TWO SUTURES WERE REQUIRED.

EE WAS USING A UTILITY KNIFE TO REMOVE THE INSULATION FROM ELECTRICAL CABLES THAT WERE TO BE USED FOR EXTENSION CORDS. THE KNIFE SLIPPED AND HE CUT HIS LEFT INDEX FINGER. THREE SUTURES WERE IN STALLED.

EE WAS ASSISTING IN THE REPLACING OF A SHEAR JACK ON A CONT MINER HE WAS USING A SLATE BAR TO LIFT & MANEUVER THE SHEAR JACK SO THAT A PIN COULDBE INSTALLED. WHILE DOING THIS THE SLATE BAR SLI PPED & EE'S RIGHT HAND WAS PINCHED BETWEEN THE BAR & THE FRAME OF THE CONT MINER

EE WAS CUTTING DOWN A TELEPHONE SUPPORTED BY PLASTIC TIES. AS HE WAS CUTTING THE TIES, THE PHONE FELL KNOCKING THE POINT OF THE RAZOR KNIFE INTO HIS LEFT FOREARM.

EE WAS REPLACING STUDS ON AN EIMCO SCOOP AXLE WHILE ANOTHER EE WAS CLEANING A "TACK WELD" OFF THE HUB USING A HAMMER & CHISEL. WHILE DOING THIS WORK A PIECE OF METAL ENTERED EE'S LEFT EYE WHIC H WAS REMOVED BY A DR. AND PRESCRIPTION MEDICATION WAS OBTAINED.

EE WAS INSTALLING A 4" VICTAULIC COUPLING ON A DEWATERING LINE, USING A 8" CRESCENT WRENCH THAT HE HAD ADJUSTED TO FIT THE HANDLE ON THE COUPLING. WHILE APPLYING PRESSURE ON THE HANDLE/WRENCH THE WRENCH SLIPPED OFF AND STRUCK HIM ACROSS HISUPPER LIP AND TEETH. THIS RESULTED INTO DAMAGE TO SEVERAL TEETH THAT WILL REQUIRE THE TEETH TO BE REMOVED LATER.

EE WAS ASSITING IN MAKING A SPLICE IN A CONVEYOR BELT. THE BELT HAD BEEN SQUARED AND EE HAD ROLLED TH EDGE OF THE BELT TO MAKE THE CUT. WHILE DOING THIS THE UTILITY KNFIE HE WAS USING CONTAC TED HIS LEFT INDEX FINGER AND LACERATED IT. THIS LACERATION REQUIRED FIVE SUTURES TO CLOSE.

EE WAS STANDING ON TOP OF THE 10 LEFT SECTION TAILPIECE USING A SLATE BAR TO PRY THE SKIRT RUBBER ON THAT TAILPIECE UP. WHEN HE PUSHED DOWN ON THE SLATE BAR, HE EXPERIENCED SOME PAIN IN THE RI GHT SIDE OF HIS GROIN. ON 11/30/98 HE BEGAN A SERIES OF PHYSICAL THERAPY TREATMENTS FOR A PULLED GROIN MUSCLE.

EE WAS USING A UTILITY KNIFE TO MARK A PIECE OF BELT FOR SPLICING AS PART OF A BELT MOVE. HE LIFTED THE CONVEYOR BELT UP TO MARK THE CENTER AND THE KNIFE CUT THRU THE BELT AND LACERATED HIS LE FT LITTLE FINGER. FIVE SUTURES WERE REQUIRED.

EE WAS JACKING UP A NEW HEADFRAME USING A 5 TON JACK. HE WAS USING A 1" BOLTER STEEL AS A JACK HANDLE. AS EE AND A COWORKER PUSHING DOWN ON THE DRILL STEEL IT BROKE. EE FEL FORWARD STRIKING HI S HEAD ON A BEAM RESULTING IN A LACERATION REQUIRING STITCHES.

EE'S LOCKER & BASKET HAD BEEN MOVED TO ANOTHER LOCATION IN THE BATHOUSE. WHILE PULLING THE BASKET UP THE SHEAVE WHEEL BECAME LODGED CAUSING THE CHAIN TO BE JERKED HARD. THIS RESULTED INTO A ST RAIN TO HIS RIGHT LITTLE FINGER. EE RECD MEDICALTREAMENT WHICH DID NOT MEET REPORTING CRITERIA. DURING THE WEEK OF 1/18/99 HE BEGAN THERAPY TREATMENTS

EE WAS WORKING WITH A CREW THAT WAS UNLOADING CONVEYOR BELT ON THE B-6 LONGWALL TRACK. WHEN THE BELT WAS UNLOADED OFF OF THE SUPPLY CARS SOME OF THE BELT LANDED ON THE MINE TRACK. EE WAS USING A SLATE BAR ATTEMPTING TO MOVE THE BELT OFF OF THE RAIL WHEN HE EXPERIENCED PAIN IN HIS LWOER LEFT ABDOMEN.

HE WAS USING A HAMMER TO BREAK UP OVERSIZED COAL PIECES THAT WERE PLUGGING UP A FEEDER. WHILE DOING THIS HIS HAND STRUCK THE FEEDER FRAME, RESULTING INTO A LACERATION TO HIS RIGHT INDEX FINGER . FOUR STITCHES WERE REQUIRED.

EE WAS USING A RAZOR KNIFE TO UNLOCK A CABLE TIE. WHEN REHOOKING THE TIE IT SLIPPED APART. HE WAS STILL HOLDING THE KNIFE IN HIS RIGHT HAND WITH THE BLADE OPEN. THE BLADE STRUCK HIS LEFT HAND CUTTING IT BETWEEN THE INDEX FINGER AND THUMB (5 STITCHES).

EE WAS USING A HAMMER & A BELT PUNCH TO CUT HOLES IN A PIECE OF CONVEYOR BELT THAT WAS TO BE USED AS A FLAP. WHILE HITTING THE PUNCH A PIECE OF METAL ENTERED HIS LEFT HAND. THIS PIECE OF METAL WAS REMOVED FROM HIS HAND ON MAY 5, 1998.

EE WAS CUTTING A SPLICE KIT OFF OF A PUMP THAT HE HAD TAPED ON EARLIER. HE CUT HIS LEFT THUMB WITH A RAZOR KNIFE. THE CUT REQUIRED 5 STITCHES.

A PIECE OF RUBBER WAS BEING INSTALLED ON THE SOUTH MAINS TAILPIECE. A HOLE HAD TO BE CUT INTO THE RUBBER THAT WAS TO BE USED AS A BOLT HOLE. WHLE CUTTING THE HOLE, THE KNIFE SLIPPED AND LACERE TED EE'S LEFT HAND REQURING 2 SUTURES TO CLOSE.

EMPLOYEE WAS RELEASING A COME-A-LONG AND THE HANDLE HIT HIM ON THE LEFT HAND FRACTURING HIS LEFT LITTLE FINGER.

EE WAS USING A UTILITY (RAZOR)KNIFE TO CUT THE PLASTIC TIES THAT WERE BEING USED TO SECURE A 2" PVE PIPE TO THE MINE ROOF. WHILE DOING THIS THE KNIFE SLIPPED AND STRUCK EE ON THE LEFT FOREARM THIS RESULTED INTO A LACERATION WHICH REQUIRE FOUR SUTURES TO CLOSE.

EE WAS PUTTING A PLASTIC TIE ON HIS TOOL POUCH. AS HE WAS CUTTING THE END OF THE TIE OFF HIS UTILITY KNIFE SLIPPED, LACERATING HIS RT THUMB. FOUR SUTURES WERE REQUIRED.

EE WAS HELPING TO REPLACE A BELT SCRAPER AT THE G3 BELT TRANSFER STATION. A PIPE WAS BEING USED TO HOLD THE SCRAPER WITH EE ON ONE END AND ANOTHER EE ON THE OTHER END/ OTHER EE DROPPED HIS END OF THE PIPE WHICH CAUSED EE 'S END OF THE PIPE TO RAISE UP EE'S RIGHT THUMB WAS PINCHED BETWEEN THE PIPE AND CHUTE FRAME LACERATING IT 5 SUTURES

EE WAS HELPING REMOVE THE CYLINDER HEAD FROM THEMOTOR OF A DART TRUCK. THE CYLINDER HEAD WAS STUCK TO THE MOTOR BLOCK AND EE WAS USING A PRY BARTO FREE THE HEAD. WHEN THE HEAD CAME LOOSE HIS F INGERS WERE SMASHED BETWEEN THE PRY BAR AND THE TRUCK FRAME. THIS RESULTED IN A FRACTURE TO HIS RIGHT LITTLE

EMPLOYEE WAS CUTTING A NOTH IN THE TROLLEY GUARDING,TO INSTALL A NIP STATION. THE RAZOR KNIFE SLIPPED CUTTING EMPLOYEE ON THE LEFT HAND.(STITCHES)

THE EE HAD USED A UTLITY KNIFE TO TRIM A PIECE OF "SKIRT" RUBBER AT THE TAIL OF THE G-2 BELT. AFTER COMPLETING THE JOB HE THOUGHT HE HAD CLOSED THE UTILITY KNIFE BUT HAD NOT. WHEN HE CLIMBED O FF THE SIDE BOARD THE KNIFE STRUCK HIS RIGHT LEG, BETWEEN THE KNEE & HIP, RESULTING IN A LACERATION WHICH REQUIRED SUTURES TO CLOSE.

HE WAS OBSERVING TWO EMPLOYEES WHO WERE REPLACING IMPACT ROLLERS AT A BELT TRANSFER. IN THE AREA WAS WAS A BUCKET (UNOPENED) THAT CONTAINED BELT CHAINS AND HE KNEW THAT THEY WOULD NEED SOME SO ON. WHILE ATTEMPTING TO CUT THE OPENING SLOT ON THE PLASTIC BUCKET LID, THE KNIFE BLADE PASSED THRY THE SLOT AND LID, LACERATING HIS LEFT MIDDLE FINGER. SUTURES WERE REQUIRED.

THE DTP WATER COUPLING BEARING ON THE LONGWALL TAILDRIVE HAD FAILED AND WORK WAS BEING DONE TO UNBOLT THE COUPLING FLANGE FORM THE CLUTCH. EE HAD HIS HAND ON THE WRENCH BEING USED TO SEE HOW M AY BOLTS WERE LEFT TO BE REMOVED, WHEN THE CONVEYOR CHAIN SUDDENLY MOVED. WHEN THIS OCCURRED THE WRENCH ALSO MOVE EE'S LEFT HAND WAS PINCHED BETWEEN THE WRENCH AND THE COUPLING HOUSING. FRACT

EE WAS ASSISTING IN TAKING SOME SLACK OUT OF THE R1 REFUSE BELT. THE SLACK HAD BEEN TAKEN OUT OF THE BELT AND HE WAS IN THE PROCESS OF TIGHTENING TH EBOLTS TO SECURE THE TAKE UP TO THE TAILPIE CE H BEAM. WHILE TIGHTENING THE BOLTS HE EXPERIENCED SOME LOWER BACK PAINS.

EE WAS USING A LIFTING JACK TO PUT A DERAILED CAR BACK ONTO THE TRACK. HE WAS PUSHING ON THE JACK BAR AND WAS NOT AWARE THAT THE JACK HAD REACH ITS FULL EXTENSION. THE BAR SPRANG BACK AND STRU CK EE ON THE RIGHT SIDE OF HIS JAW RESULTING INTO A LACERATION REQUIRING 2 SUTURES TO CLOSE.