Buscar en el registro

A MECHANIC 1ST CLASS WAS INSTALLING A PROPEL CHAIN ON A DRILL. HE WAS USING A ROPE TO PULL THE CAHIN OVER THE PSROCKET. THE CHAIN PULLED TIGHT AND CAUSED THE ROPE TO BE PULLED THROUGH HIS THUM B AND FIRST FINGER. THE ROPE CUT HIS HAND AND REQUIRED STITCHES.

EE WAS CUTTING A BOX WITH A HOOK KNIFE. THE KNIFE SLIPPED AND CUT HIS LEFT HAND HE HAD ON TOP OF THE BOX.

PRINCIPAL WAS LOWERING THE COVER OF A HEAVY MEDIA PUMP TO THE FLOOR WITH THE USE OF A COME-A-LONG. THE PRESSURE OF THE WATER ABOVE THE PUMP BROKE LOOSE AND FORCED THE COVER SPINNING ALONG WITH THE COME-A-LONG. THE HANDLE OF THE COME-A-LONG STRUCK THE PRINCIPAL ON THE RIGHT SIDE OF HIS MOUTH.

PRINCIPAL WAS USING A NON-LOCKING POCKET KNIFE TO CUT A HOLE IN SKIRTING BELT TO HANG AROUND TAIL END OF RAW COAL BELTS. AS PRINCIPAL TRIED TO CUT A HOLE THE BLADE FOLDED OVER ON HIS RIGHT IND EX FINGER CUTTING IT.

AN EMPLOYEE WAS TIGHTENING A LOCK NUT ON A 2570-W DRAGLINE BELLY SUPPORT CABLE WITH A #4 HAMMER. A SUPERVISORS LEFT HAND RING FINGER WAS STRUCK BY THE HAMMER. THE FINGER REQUIRED SUTURING OF T HE WOUND.

EE AND COWORKERS WERE REMOVING A 7" PIN FROM THE DUMP RIGGIN OF A DRAGLINE. A BAR WAS BEING USED TO "TAP" THE PIN OUT. WHEN THE PIN CAME OUT, THE BAR WAS PINCHED BETWEEN THE RIGGING AND RECOIL ED INTO EE'S RIGHT CHEEK.

PRINCIPAL AND CO-WORKER WERE REMOVING A REAR TIRE FROM A FORD TRACTOR. THE PRINCIPAL STRUCK THE TIRE WITH A SLEDGE HAMMER. THE TIRE CAME OFF THE TRACTOR AND STRUCK HIM ON HIS RIGHT FOREHEAD.

PRINCIPAL AND CO-WORKERS WERE USING A B&O HAMMER AND SLEDGE HAMMER TO INSTALL A WHEEL BEARING ON 36030 DART COAL HAULER. A SLIVER OF STEEL BROKE AWAY FROM THE B&O AND STRUCK THE PRINCIPAL IN T HE RIGHT CHEEK. PRINCIPAL RECEIVED TWO SUTURES.

PRINCIPAL WAS ASSISTING COWORKERS REPLACING DRIVE MECHANISMS ON A COAL SCREEN AT THE PREP PLANT.HE AND COWORKERS PERFORMED NORMAL WORK ACTIVITIES SUCH AS PUSHING-PULLING-TWISTING-AND BENDING OVER AND USING A SLEDGE HAMMER. NEAR THE END OF THE SHIFT AT 11:00PM, HE STATED HIS BACK WAS SORE.

PRINCIPAL WAS CUTTING RUBBER BELTING WITH A KNIFE. WHILE CUTTING THE KNIFE SLIPPED FROM THE BELT AND STRUCK THE INSIDE AREA OF THE LEFT KNEE.

USING A PRY BAR TO HOLD A METAL PLATE AGAINST A SHAW BOX HOIST, THE PLATE SLIPPED AND STRUCK THE RING FINGER ON THE LEFT HAND. RECEIVED SIX SUTURES.

TTHE PRINCIPAL WAS USING A SLEDGE HAMMR TO REMOVE A TOOTH FROM A D9L RIPPER SHANK. A PIECE OF STEEEL BROKE FROM THE TOOTH AND STRUCK THE PRINCIPAL ABOVE THE CALF MUSCLE ON THE RIGHT LEG.

PULLING ON SPUD WRENCH WRENCH SLPPED END OF HANDLE STRUCK FOREHEAD

INJURED WAS REMOVING A STAUB PIN (6IN IN DIAMETER) OF A DOOR HINGE AS THE PIN BECAME FREE IT DROPPED STRIKING LEFT INDEX FINGER PINCHING IT BETWEEN THE PIN & THE FLOOR CAUSING A LACERATION

UNHOOKING CHOKER R HAND PINCHED AGAINST CRANE BLOCK, IT SHIFTED SLIGHTLY TO CAUSE CHOKER TO TIGHTEN

EE WAS UNLOADING PARTS CHAIN SLIPPED STRIKING SAFETY GLASSES CAUSING LACERATION ABOVE RIGHT EYE.

EMPLOYEE WAS HOLDING A KNIFE IN HIS RIGHT HAND ATTEMPTING TO CUT OPEN A CARDBOARD BOX. AS HE MOVED HIS HAND TOWARD THE BOX, HE BUMPED THE BOTTOM OF THE BOX CAUSING HIM TO LOSE HIS GRIP ON THE KNIFE, CUTTING HIS RIGHT INDEX FINGER.

EMPLOYEE WAS USING A SLEDGE HAMMER TO STRIKE A B & O BEING HELD BY ANOTHER EMPLOYEE,WHEN STRUCK A PICE OF METAL BROKE OFF THE B&0 STRIKING EMPLOYEE ON LIP BELOW NOSE.

REMOVING JACKET FROM WELDING LEAD TO QUICK CONNECT FEMALE END, USING POCKET KNIFE, KNIFE SLIPPED CAUSING CUT ACROSS BACK OF RIGHT HAND. (RECEIVED 6 STITCHES.)

EE WAS FASTENING DOWN A MOTOR ON LOW BOY TRAILER WITH CHAIN BINDERS, WHEN BINDER SLIPPED CAUSING PIPE BEING USED ON HANDLE TO HIT HIM ON FOREHEAD, BETWEEN EYES. RECEIVED FIVE STITCHES.

EMPLOYEE WAS USING A SLEDGE HAMMER ON FRONT BUMPER OF FUEL TRUCK.AS HE WAS SWINGING THE SLEDGE ,THE SLEDGE WENT UNDER BUMPER CAUSING HIS FINGER TO BE CAUGHT BETWEEN SLEDGE HAMMER AND BUMPER.

USING COME A LONG TO REMOVE ROD FROM INSIDE TOOL DOG JACKING WITH COME ALONG, SLING BROKE CAUSING TOOL DOG TO FALL ON TOP OF R FOOT

EMPLOYEE WAS REPLACING A 14IN WATER PIPE & WAS USING TWO COME-A-LONGS TO JACK UP THE PIPE AS THE WEIGHT OF THE COME-A-LONG TO ALSO SWING & IT STRUCK THE EMPLOYEE ON THE LEFT SIDE OF THE HEAD ( RECEIVED STITCHES)

INJURED WAS USING A B&O HAMMER TO REMOVE THE HOIST JACK YOKE OUT OF THE BOSS ON THE NUMBER 16 GRADER. AS HE STRUCK THE B&O HAMMER WITH A 2 LB SLEDGE HAMMER, A PIECE OF METAL BROKE OFF LODGING ITSELF IN TOP OF INJURED'S RIGHT HAND. LACERATION WAS LESS THAN 1/4 INCH IN WIDTH.

EMPL WAS DRIVING SPIKE AT RAILROAD SWITCH AT COMPLEX WHEN HE GOT THUMB BETWEEN SPIKE & A0 LB SLEDGE HAMMER.

EMPL TAKING BEARING OFF HITCH PIN WITH HAMMER AND PUNCH.PIECE OF STEEL CAME OFF PUNCH AND INBEDDED INTO LEFT WRIST.

EMPL USING STEEL WRENCH TO TAKE STEELS OUT.WRENCH WAS IN WRONG POSITION BEHIND STEEL RACK.WHEN SHE LIFTED WRENCH SHE SUFFERED PAIN IN LOWER BACK.

RELEASING CHAIN BINDER FROM SET OF CHAINS SECURING BULL GEAR TO BOOM TRUCK.AT HALFWAY POINT,HANDLE OF BINDER RELEASED SUDDENLY.HANDLE STRUCK EMPL IN LEFT KNEE.LACERATION REQ 3 STITCHES.

EMPLOYEE WAS HOLDING BAR WHILE CO-WORKER WAS USING SLEDGE HAMMER TO DRILL TRACK PIN IN PLACE, WHEN SLEDGE HIT BAR A CHUNK OF METAL BROKE OFF AND STRUCK EMPLOYEE ON RIGHT FOREARM.

EMPLOYEE JACKING AFTEY CABLE ON LEGS DRAGLINE, DOWN AND AWY FROM A LEGS WHEN A PORTA POWER SLIPPED AND HIT HIM ON THE LEFT SIDE OF THE HEAD AND NECK INJURING MUSCLES IN NECK AND SHOULDER.

EMPLOYEE WAS RELEASING PRESSURE ON SAFTEY CABLE WHEN PORTAPOWER JUMPED OUT BETWEEN JACKING PLATE AND ANCHOR BLOCK HITTING HIS RIGHT SHOULDER.

LIFTING 1-1/2 IN PLATE STEEL WIHT COME-A ALONG CABLE WAS ACCIDENTLY RELEASED CAUSING THE PLATE TO FALL ON EMPLOYEE KNOCKING HIM DOWN AND LANDING ON HIS RT KNEE

TORQUING BOLTS AND ADAPTER ON WRENCH BROKE CAUSING EMP TO FALL BACKWARD SPRAINING L. ANKLE.

REMOVING A SECTION OF WALL AND FLOOR FROM REVOLVING FRAME OF THE 4250W SECTION APPROX. 3" THICK BY 4'. HAD FINISHED CUTTING WITH TORCH, PIECE HAD WEDGED. EMPLOYEE USED A SLEDGE HAMMER TO KNOCK IT LOOSE. WHEN THE PIECE CAME LOOSE, IT DROPPED ON DOWN TO THE TOP OF STUB. HIS FINGER HAD CAUGHT BETWEEN SOMETHING- EMPLOYEE DOESN'T KNOW WHAT.

EMPLOYEE WAS TIGHTENING A BOLT WITH A CRESCENT WRENCH, THE WRENCH CAME LOOSE FROM THE BOLT AND CAME UP AND HIT THE EMPLOYEE BETWEEN THE EYES ON THE FOREHEAD, CAUSING A CUT BUMP.

EMPL WAS SLEDGING PIN INTO BUCKET TOOTH USING SLEDGE HAMMER & B & O. SMALL PIECE OF STEEL FROM B & O BROKE OFF STRIKING EMPL'S LEFT FOREARM.

A PIECE OF STEEL ABOUT 100 LBS CAME OFF THE LIFTING JACK AND HIT EMPLOYEES LEFT LEG - STEEL DROPPED ABOUT 4 FT.

EMPL WAS HELPING TO HOOK UP CHOCKER TO D10 DOZER WITH RIPPER. HE BENT OVER TO HOOK IT UP & FEL HIS BACK GIVE OUT.

EMPLOYEE WAS HITTING A STEEL SUPPORT BRACE WITH SLEDGE HAMMER TO WEDGE INTO PROPER PLACE...CAUGHT HIS FINGERS BEHIND THE BRACE WHEN HE HIT IT WITH THE 10 LB SLEDGE.

EMPLOYEE WAS WORKING ON SETTING THE RAILS ON THE 2570 DRAGLINE ANOTHER EMPOLOYEE WAS CHIPPING SLAG NEAR HIM AND A PIECE OF SLAG WENT INTO HIS LEFT EYE BECOMING EMBEDDED

EMPLOYEE WAS GRINDING WITH A JET GRINDER AND LOST FOOTING AND GRINDER SLIPPED CUTTING HIS RIGHT WRIST WITH GRINDING DISC

PUSHED HYDRAULIC TRAMSMISSION FACK UNDER OIL COOLER OF RADIATOR HE HAD HIS RT HAND ON JACK THE RELEASE SCREEN WAS NOT TIGHT THE MOVEMENT OF THE JACK CAUSED THE ARM TO LOWER TO ITS LOWEST SECT ION CATCHING EMPLOYEES RT LITTLE FINGER

EMPLOYEE WAS ATTEMPTING TO TIGHTEN SWING CASE, HAD TO REMOVE DECK PLATE BOLTS HAD 12" CRESCENT WRENCH IN LEFT HAND TO HOLD NUT UNDER FLOOR IMPACT WRENCH IN RIGHT HAND, CAUSED CRESCENT WRENCH T O TURN CATCHING HIS FINGER BETWEEN CRESCENT WRENCH AND SWING CASE.

EMPLOYEE WAS CL9ANING THE GEAR SEGMENT WITH A PAINT BRUSH AND FOREIGN LIQUID MATERIAL GOT INTO HIS LEFT EYE...WASHED OUT AT JOB SITE AND THEN TOOK TO HOSPITAL FOR MEDICAL TREATMENT.

REMOVING SECTION AO WALL AND FLOOR FROM REVOLVING FRAME OF THE 4250 W SECTION APPROX 3 IN THICK BY 4F T HAD FINISHED CUTTING WITH TORCH LINE HAD WEDGED EMPLOYEE USED A SLEDGE HAMMER TO KNOCK I T LOOSE WHEN THE PIECE CAME LOOSE IT DROPPED ON DOWN TO THE TOP OF TUB HIS FINGER HAD CAUGHT BETWEEN SOMETHING EMPLOYEE DOESNT KNOW WHAT

EMPLOYEE HAD A 5 FT PRY BAR KNOCKING FROZEN BUILD UP AWAY FROM SCRAPER ON 7-2 BELT TO CHANGE OUT SCRAPER BLADE.WHEN HE RAISED BAR, THE MAGNET ATTRACTED BAR STRIKING HAND BETWEEN MAGNET AND BAR .

WAS ADJUSTING A3100 TON JACK UNDER A PIECE OF PLATE TO GIRDER OF 2570-W DRAGLINE GIRDER, JACK SLIPPED WHEN THE SEAL BUSTED AND CAUSED THE STEEL GIRDER TO SMASH HIS HAND BETWEEN THE GIRDER AND STEEL PLATE. 3

REMOVING A SECT3ON OF WALL & FLOOR FROM REVOLVING FRAME OF THE 4250W SECTION 3 THICK BY 4 SQUARE. HAD FINISHED CUTTING WITH TORCH PIECE HAD WIDGED EMP USED A SLEDGE HAMMER TO KNOCK IT LOOSE WH EN THE PIECE CA4E LOOSE, IT DROPPED ON DOWN TO THE TOP OF STUB. HIS FINGER HAD CAUGHT BETWEEN SOME THING HE DOESNT KNOW WAHT

EMPLOYEE WAS BO9ING SHEAVEON RADIAL DRILL WITH BORING BAR. HE WAS ADJUSTING TOOL IT WHEN BORING BAR FELL FROM SPINDLE ON DRILL, STRIKING HIM FINGER BETWEEN SHEAVE AND CUTTING TOOL.

EMPLOYEES WERE 9EMOVING SEGMENTS FROM A D8K DOZER DRIVE SPROCKET. COWORKER SWUNG SLEDGE HAMMER STRIKING THE SEGMENT WHEN A PIECE OF METAL BROKE OFF SPROCKET SEGMENT STRIKING EMP ON LEFT FOREA