Buscar en el registro

EE was using a sleever bar to line up a bolt hole for a brace in a truss that was set on the ground. While attempting to put a bolt in the other end, standing on a clip about 26" off the ground, his foot slipped causing him to fall against the sleever bar.

INSTALLING SUPPORT BEAM - SWINGING SLEDGE HAMMER TO INSTALL BEAM, HAMMER CAUGHT, SMASHING POINTING FINGER AND TWISTING KNEE.

EE WAS ATTEMPTING TO TRIM A TORN MUD FLAP WITH A POCKET KNIFE. THE KNIFE SLIPPED & CUT AN INCISION ACROSS ALL FOUR FINGERS ON THE LEFT HAND. ALL FOUR FINGERS REQUIRED STITCHES.

EE AND COWORKER WERE PERFORMING MAINTENANCE WORK ON A HEAVY MEDIA CYCLONE PUMP WHEN THE ACCIDENT OCCURRED. AS THE EE USED A 1-1/2 TON CHAIN FALL TO MAEUVER THE PUMP HOUSING, THE HOUSING'S I-BO LT STRIPPED OUT AND THE HOUSING FELL, STRIKING HIS RIGHT LEG. THIS RESULTED IN A FRACTURE TO HIS RIGHT KNEE.

EE WAS IN PROCESS OF STRIPPING INSULATION FOR A 14/3 POWER CABLE FOR AN OCENCO AR100 LIGHT FIX FOR FLETCHER RR11 ROOF BOLT MACH. AS EE WAS USEING POCKET KNIFE TO STRIP INSULATION KNIFE SLIPPE AND EE CUT RIGHT THIGH 1-1/2 IN L 1" DEEP CUT EE WENT TO EMERG OF LOCAL HOSP-SUTURES WERE REQ TO CLOSE WOUND. EE RETD TO WORK AND FINSHED REG SHIFT. NO TIME LOST

EMPLOYEE & A COWORKER WERE USING A SLATE BAR TO POSITION A TRAM MOTOR ON A JOY 14CM-9 CONTINUOUS MINER THE EMPLOYEE REPORTED A PAIN I NHIS BACK WHILE APPLYING PHYSICAL PRESSURE TO THE SLATE BA R THIS ACCIDENT DID NOT BECOME R EPORTABLE UNTIL10-04-94 WHEN EMPLOYEE BEGAN TO MISS WORK THIS EVENT SHOULD BE CATEGORIZED AS A DEGREE 3 CLASSIFICATION 10 ACCIDENT

CHANGING PROFILE SCREEN DRIVING WEDGES & HIT LEFT HAND WITH BALLPIN HAMMER

WHILE REPLACING THE TOP OF A REFUSE DRYER, HE WAS USING A SMALL LINE UP BAR TO CENTER UP THE TOP. HIS BAR SLIPPED CAUSING HIM TO FALL ABOUT 6 FEET OFF THE SIDE OF DRYER.

EMPLOYEE WAS USING A HAMMER TO POUND ON CLEVIS ON THE SAFETY CHAIN CONNECTED TO A SUPPLY CAR. AS HE WAS STRIKING THE CLEVIS WITH HAMMER THE HAMMER GLANCED OFF THE CLEVIS & STRUCK HIM ON THE L EFT KNEE RESULTING IN A CONTUSSION. THIS ACCIDENT SHOULD BE CLASSIFIED AS DEGREE 3 & CLASSIFICATION 10.

EE WAS USING A STANDARD METAL SLATE BAR TO PRY SOME ROCK DOWN FROM THE ROOF. THE SLATE BAR MOVED CAUSING THE EE TO STRIKE HIS RIGHT HAND ON THE COAL; RIB RESULTING IN A LACERATION THE RQUIRED SUTURES. THIS ACCIDENT SHOULD BE CLASIFIED AS A HAND TOOLS ACCIDENT SINCE THE MOTION OF THE HAND TOOL CAUSED THE INJURY.

ASSISTING ANOTHER EMPLOYEE THAT WAS USING HAMMER TO REMOVE PIN FROM BELT SPLICE. PIECE OF HAMMER CHIPPED OFF AND STRUCK RIGHT WRIST CAUSING PUNCTURE WOUND.

INDIVIDUAL WAS DOWN ON HIS KNEES CUTTING A PIECE OF BELT FOR A GUARD AND WHEN HE BENT OVER TO CUT THE BELT, HE FELT A PAIN IN HIS LOWER BACK.

INDIVIDUAL WAS IN THE PROCESS OF SLIDING THE TRACK (RAIL) OVER (TOO CLOSE TO BELT LINE). THE 60-POUND RAIL FELL OFF THE JACK AND DOWN ON THE INDIVIDUAL'S LEFT ANKLE.

INDIVIDUAL WAS RAISING RUB RAIL WITH CHAIN RATCHET, CHAIN SLIPPED AND EE (RIGHT) WAS BETWEEN RUB RAIL AND BRACKET. (WAS PULLING KEEPER SHIM OUT WITH CHAIN HOIST).

95495IDUAL WAS WORKING ON CABLE SPOOLING DEVICE FOR SHUTTLE CAR CABLE GUIDE SLIPPED DOWN HITTING LEFT RING FINGER.

PULLING CHARGER INTO MANTRIP WITH CHAIN RATCHET.THE CHAIN SLIPPED OUT WHEN BEING RELEASED.THE HANDLE HIT THE INDIVIDUAL OVER THE RIGHT EYE CAUSING A LACERATION.

I WAS KNOCKING TIMBERS & ONE FELL & LANDED ON FOOT.

REMOVING PIN OUT OF MACHINE,HE WAS HOLDING A BAR FOR A CO-WORKER TO HIT WITH A HAMMER.WHEN THE PIN BROKE LOOSE,HIS FINGER WENT INTO THE HOLE AND WAS CAUGHT BY THE BAR.

USING A JACK TO PUT THE MANBUS BACK ON TRACK. WHEN HE PUSHED THE MANBUS OVER THE JACK FELL ON HIS HAND CRUSHING HIS LITTLE FINGER.

TRYING TO BREAK OFF A BOLT AND HIT HIS HAND WITH THE HAMMER.

DRAGGING MINER CABLE OUT OF ROADWAY WITH PICKHAMMER,IT SLIPPED OFF CABLE AND HIT HIS ANKLE.

HOLDING WATER LINE WHILE ANOTHER EMPLOYEE WAS SAWING THE LINE, SAW SLIPPED HITTING HIS HAND.

KNOCKING OUT AN OLD BIT WHILE HOLDING ANOTHER BIT IN ONE HAND AND HIT HIS HAND WITH THE HAMMER

HELPING MOVE A LARGE WATER PUMP TO SET IN POSITION TO PUT IN OPERATION HE WAS USING A BAR TO LIFT THE PUMP

DRIVING WEDGES 3N MINER DRUM AND THE HAMMER HANDLE BROKE CAUSING THE HAMMER TO HIT HIS LEFT ARM.

HE WAS RETRACKI3G CAT 215 EXCAVATOR WHILE USING A SLATE BAR TO PRY ON TRACK HE STSRAINED HIS BACK

HE WAS WORKING 2N A TRUCK. HE WAS UDER THE TRUCK PUTTING ON A STEERING JACK AND THE JACK SLIPPED. HE CAUGHT THE JACK TO KEEP IT FROM FALLING ON HIM.

HE WAS REPLACING A BEARING ON A ROLLER USING A SMALL ALLEN WRENCH & A HAMMER. HE HIT THE WRENCH WITH THE HAMMER THE WRENCH FLEW UP STRIKING HIM IN T HE EYE.

HE WRECKED BATTERY SCOOTER AND WAS JACKING SCOOTER BACK ON AND HURT HIS BACK

HE WAS USING JACK TO PUT MOTOR BACK - WHILE PUTTING MOTOR BACK ON THE TRACK, THE JACK BAR SLIPPED

WHILE KNOCKING A BIT OUT OF MINER HIT HIMSELF WITH THE HANDLE OF HAMMER IN GROINS

HE WAS SERVICING THE MINER WRENCH SLIPPED WHILE PUTTING OIL IN RIPPER HEAD AND HIT HIS ELBOW

PUTTING CAR DOOR UP WITH A BAR.